Merge branch 'master' of git://git.denx.de/u-boot-net

arch/arm/cpu/arm926ejs/lpc32xx/devices.c

@@ -45,7 +45,12 @@ void lpc32xx_mac_init(void)
 {
 	/* Enable MAC interface */
 	writel(CLK_MAC_REG | CLK_MAC_SLAVE | CLK_MAC_MASTER
-		| CLK_MAC_MII, &clk->macclk_ctrl);
+#if defined(CONFIG_RMII)
+		| CLK_MAC_RMII,
+#else
+		| CLK_MAC_MII,
+#endif
+		&clk->macclk_ctrl);
 }
 
 void lpc32xx_mlc_nand_init(void)

drivers/net/davinci_emac.c

@@ -598,7 +598,8 @@ static void davinci_eth_close(struct eth_device *dev)
 	debug_emac("+ emac_close\n");
 
 	davinci_eth_ch_teardown(EMAC_CH_TX);	/* TX Channel teardown */
-	davinci_eth_ch_teardown(EMAC_CH_RX);	/* RX Channel teardown */
+	if (readl(&adap_emac->RXCONTROL) & 1)
+		davinci_eth_ch_teardown(EMAC_CH_RX); /* RX Channel teardown */
 
 	/* Reset EMAC module and disable interrupts in wrapper */
 	writel(1, &adap_emac->SOFTRESET);

drivers/net/e1000.c

@@ -126,6 +126,7 @@ static int e1000_detect_gig_phy(struct e1000_hw *hw);
 static void e1000_set_media_type(struct e1000_hw *hw);
 
 static int32_t e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask);
+static void e1000_swfw_sync_release(struct e1000_hw *hw, uint16_t mask);
 static int32_t e1000_check_phy_reset_block(struct e1000_hw *hw);
 
 #ifndef CONFIG_E1000_NO_NVM
@@ -729,7 +730,10 @@ void e1000_release_eeprom(struct e1000_hw *hw)
 		eecd &= ~E1000_EECD_REQ;
 		E1000_WRITE_REG(hw, EECD, eecd);
 	}
+
+	e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM);
 }
+
 /******************************************************************************
  * Reads a 16 bit word from the EEPROM.
  *
@@ -992,10 +996,6 @@ e1000_get_software_semaphore(struct e1000_hw *hw)
 
 	DEBUGFUNC();
 
-		swsm = E1000_READ_REG(hw, SWSM);
-		swsm &= ~E1000_SWSM_SMBI;
-		E1000_WRITE_REG(hw, SWSM, swsm);
-
 	if (hw->mac_type != e1000_80003es2lan)
 		return E1000_SUCCESS;
 
@@ -1102,6 +1102,7 @@ e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw)
 	return E1000_SUCCESS;
 }
 
+/* Take ownership of the PHY */
 static int32_t
 e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask)
 {
@@ -1115,10 +1116,7 @@ e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask)
 		if (e1000_get_hw_eeprom_semaphore(hw))
 			return -E1000_ERR_SWFW_SYNC;
 
-		if (hw->mac_type == e1000_igb)
-			swfw_sync = E1000_READ_REG(hw, I210_SW_FW_SYNC);
-		else
-			swfw_sync = E1000_READ_REG(hw, SW_FW_SYNC);
+		swfw_sync = E1000_READ_REG(hw, SW_FW_SYNC);
 		if (!(swfw_sync & (fwmask | swmask)))
 			break;
 
@@ -1141,6 +1139,21 @@ e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask)
 	return E1000_SUCCESS;
 }
 
+static void e1000_swfw_sync_release(struct e1000_hw *hw, uint16_t mask)
+{
+	uint32_t swfw_sync = 0;
+
+	DEBUGFUNC();
+	while (e1000_get_hw_eeprom_semaphore(hw))
+		; /* Empty */
+
+	swfw_sync = E1000_READ_REG(hw, SW_FW_SYNC);
+	swfw_sync &= ~mask;
+	E1000_WRITE_REG(hw, SW_FW_SYNC, swfw_sync);
+
+	e1000_put_hw_eeprom_semaphore(hw);
+}
+
 static bool e1000_is_second_port(struct e1000_hw *hw)
 {
 	switch (hw->mac_type) {
@@ -4004,7 +4017,7 @@ e1000_wait_autoneg(struct e1000_hw *hw)
 	DEBUGFUNC();
 	DEBUGOUT("Waiting for Auto-Neg to complete.\n");
 
-	/* We will wait for autoneg to complete or 4.5 seconds to expire. */
+	/* We will wait for autoneg to complete or timeout to expire. */
 	for (i = PHY_AUTO_NEG_TIME; i > 0; i--) {
 		/* Read the MII Status Register and wait for Auto-Neg
 		 * Complete bit to be set.
@@ -4438,6 +4451,7 @@ e1000_phy_hw_reset(struct e1000_hw *hw)
 
 		if (hw->mac_type >= e1000_82571)
 			mdelay(10);
+
 	} else {
 		/* Read the Extended Device Control Register, assert the PHY_RESET_DIR
 		 * bit to put the PHY into reset. Then, take it out of reset.
@@ -4462,6 +4476,8 @@ e1000_phy_hw_reset(struct e1000_hw *hw)
 		E1000_WRITE_REG(hw, LEDCTL, led_ctrl);
 	}
 
+	e1000_swfw_sync_release(hw, swfw);
+
 	/* Wait for FW to finish PHY configuration. */
 	ret_val = e1000_get_phy_cfg_done(hw);
 	if (ret_val != E1000_SUCCESS)

drivers/net/e1000.h

@@ -2460,7 +2460,7 @@ struct e1000_hw {
 #define MII_CR_SPEED_100		0x2000
 #define MII_CR_SPEED_10		0x0000
 #define E1000_PHY_ADDRESS		0x01
-#define PHY_AUTO_NEG_TIME		45	/* 4.5 Seconds */
+#define PHY_AUTO_NEG_TIME		80	/* 8.0 Seconds */
 #define PHY_FORCE_TIME			20	/* 2.0 Seconds */
 #define PHY_REVISION_MASK		0xFFFFFFF0
 #define DEVICE_SPEED_MASK		0x00000300	/* Device Ctrl Reg Speed Mask */
@@ -2496,7 +2496,6 @@ struct e1000_hw {
 #define ICH_GFPREG_BASE_MASK       0x1FFF
 #define ICH_FLASH_LINEAR_ADDR_MASK 0x00FFFFFF
 
-#define E1000_I210_SW_FW_SYNC 0x5B50 /* Software-Firmware Synchronization - RW */
 #define E1000_SW_FW_SYNC 0x05B5C /* Software-Firmware Synchronization - RW */
 
 /* SPI EEPROM Status Register */

drivers/net/fm/eth.c

@@ -520,6 +520,7 @@ static int fm_eth_recv(struct eth_device *dev)
 	u16 status, len;
 	u8 *data;
 	u16 offset_out;
+	int ret = 1;
 
 	fm_eth = (struct fm_eth *)dev->priv;
 	pram = fm_eth->rx_pram;
@@ -533,7 +534,7 @@ static int fm_eth_recv(struct eth_device *dev)
 			net_process_received_packet(data, len);
 		} else {
 			printf("%s: Rx error\n", dev->name);
-			return 0;
+			ret = 0;
 		}
 
 		/* clear the RxBDs */
@@ -559,7 +560,7 @@ static int fm_eth_recv(struct eth_device *dev)
 	}
 	fm_eth->cur_rxbd = (void *)rxbd;
 
-	return 1;
+	return ret;
 }
 
 static int fm_eth_init_mac(struct fm_eth *fm_eth, struct ccsr_fman *reg)

drivers/net/lpc32xx_eth.c

@@ -151,7 +151,7 @@ struct lpc32xx_eth_registers {
 #define SUPP_SPEED 0x00000100
 
 /* MCFG register bitfields/masks and offsets (see Table 292) */
-#define MCFG_CLOCK_SELECT_MASK  0x0000001C
+#define MCFG_RESET_MII_MGMT     0x00008000
 /* divide clock by 28 (see Table 293) */
 #define MCFG_CLOCK_SELECT_DIV28 0x0000001C
 
@@ -168,9 +168,10 @@ struct lpc32xx_eth_registers {
 #define COMMAND_RXENABLE      0x00000001
 #define COMMAND_TXENABLE      0x00000002
 #define COMMAND_PASSRUNTFRAME 0x00000040
+#define COMMAND_RMII          0x00000200
 #define COMMAND_FULL_DUPLEX   0x00000400
 /* Helper: general reset */
-#define COMMAND_RESETS        0x0000001C
+#define COMMAND_RESETS        0x00000038
 
 /* STATUS register bitfields/masks and offsets (see Table 283) */
 #define STATUS_RXSTATUS 0x00000001
@@ -201,6 +202,7 @@ struct lpc32xx_eth_device {
 	struct eth_device dev;
 	struct lpc32xx_eth_registers *regs;
 	struct lpc32xx_eth_buffers *bufs;
+	bool phy_rmii;
 };
 
 #define LPC32XX_ETH_DEVICE_SIZE (sizeof(struct lpc32xx_eth_device))
@@ -359,7 +361,10 @@ int lpc32xx_eth_phy_write(struct mii_dev *bus, int phy_addr, int dev_addr,
 
 static struct lpc32xx_eth_device lpc32xx_eth = {
 	.regs = (struct lpc32xx_eth_registers *)LPC32XX_ETH_BASE,
-	.bufs = (struct lpc32xx_eth_buffers *)LPC32XX_ETH_BUFS
+	.bufs = (struct lpc32xx_eth_buffers *)LPC32XX_ETH_BUFS,
+#if defined(CONFIG_RMII)
+	.phy_rmii = true,
+#endif
 };
 
 #define TX_TIMEOUT 10000
@@ -459,8 +464,22 @@ static int lpc32xx_eth_init(struct eth_device *dev)
 	struct lpc32xx_eth_buffers *bufs = lpc32xx_eth_device->bufs;
 	int index;
 
-	/* Release SOFT reset to let MII talk to PHY */
-	clrbits_le32(&regs->mac1, MAC1_SOFT_RESET);
+	/* Initial MAC initialization */
+	writel(MAC1_PASS_ALL_RX_FRAMES, &regs->mac1);
+	writel(MAC2_PAD_CRC_ENABLE | MAC2_CRC_ENABLE, &regs->mac2);
+	writel(PKTSIZE_ALIGN, &regs->maxf);
+
+	/* Retries: 15 (0xF). Collision window: 57 (0x37). */
+	writel(0x370F, &regs->clrt);
+
+	/* Set IP gap pt 2 to default 0x12 but pt 1 to non-default 0 */
+	writel(0x0012, &regs->ipgr);
+
+	/* pass runt (smaller than 64 bytes) frames */
+	if (lpc32xx_eth_device->phy_rmii)
+		writel(COMMAND_PASSRUNTFRAME | COMMAND_RMII, &regs->command);
+	else
+		writel(COMMAND_PASSRUNTFRAME, &regs->command);
 
 	/* Configure Full/Half Duplex mode */
 	if (miiphy_duplex(dev->name, CONFIG_PHY_ADDR) == FULL) {
@@ -477,20 +496,6 @@ static int lpc32xx_eth_init(struct eth_device *dev)
 	else
 		writel(0, &regs->supp);
 
-	/* Initial MAC initialization */
-	writel(MAC1_PASS_ALL_RX_FRAMES, &regs->mac1);
-	writel(MAC2_PAD_CRC_ENABLE | MAC2_CRC_ENABLE, &regs->mac2);
-	writel(PKTSIZE_ALIGN, &regs->maxf);
-
-	/* Retries: 15 (0xF). Collision window: 57 (0x37). */
-	writel(0x370F, &regs->clrt);
-
-	/* Set IP gap pt 2 to default 0x12 but pt 1 to non-default 0 */
-	writel(0x0012, &regs->ipgr);
-
-	/* pass runt (smaller than 64 bytes) frames */
-	writel(COMMAND_PASSRUNTFRAME, &regs->command);
-
 	/* Save station address */
 	writel((unsigned long) (dev->enetaddr[0] |
 		(dev->enetaddr[1] << 8)), &regs->sa2);
@@ -562,6 +567,8 @@ static int lpc32xx_eth_halt(struct eth_device *dev)
 #if defined(CONFIG_PHYLIB)
 int lpc32xx_eth_phylib_init(struct eth_device *dev, int phyid)
 {
+	struct lpc32xx_eth_device *lpc32xx_eth_device =
+		container_of(dev, struct lpc32xx_eth_device, dev);
 	struct mii_dev *bus;
 	struct phy_device *phydev;
 	int ret;
@@ -582,7 +589,11 @@ int lpc32xx_eth_phylib_init(struct eth_device *dev, int phyid)
 		return -ENOMEM;
 	}
 
-	phydev = phy_connect(bus, phyid, dev, PHY_INTERFACE_MODE_MII);
+	if (lpc32xx_eth_device->phy_rmii)
+		phydev = phy_connect(bus, phyid, dev, PHY_INTERFACE_MODE_RMII);
+	else
+		phydev = phy_connect(bus, phyid, dev, PHY_INTERFACE_MODE_MII);
+
 	if (!phydev) {
 		printf("phy_connect failed\n");
 		return -ENODEV;
@@ -604,7 +615,7 @@ int lpc32xx_eth_initialize(bd_t *bis)
 	 * Set RMII management clock rate. With HCLK at 104 MHz and
 	 * a divider of 28, this will be 3.72 MHz.
 	 */
-
+	writel(MCFG_RESET_MII_MGMT, &regs->mcfg);
 	writel(MCFG_CLOCK_SELECT_DIV28, &regs->mcfg);
 
 	/* Reset all MAC logic */
@@ -630,7 +641,7 @@ int lpc32xx_eth_initialize(bd_t *bis)
 	eth_register(dev);
 
 #if defined(CONFIG_PHYLIB)
-	lpc32xx_eth_phylib_init(dev, 0);
+	lpc32xx_eth_phylib_init(dev, CONFIG_PHY_ADDR);
 #elif defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
 	miiphy_register(dev->name, mii_reg_read, mii_reg_write);
 #endif

drivers/net/macb.c

@@ -54,6 +54,7 @@ struct macb_dma_desc {
 #define DMA_DESC_BYTES(n)	(n * sizeof(struct macb_dma_desc))
 #define MACB_TX_DMA_DESC_SIZE	(DMA_DESC_BYTES(MACB_TX_RING_SIZE))
 #define MACB_RX_DMA_DESC_SIZE	(DMA_DESC_BYTES(MACB_RX_RING_SIZE))
+#define MACB_TX_DUMMY_DMA_DESC_SIZE	(DMA_DESC_BYTES(1))
 
 #define RXADDR_USED		0x00000001
 #define RXADDR_WRAP		0x00000002
@@ -93,6 +94,9 @@ struct macb_device {
 	unsigned long		rx_ring_dma;
 	unsigned long		tx_ring_dma;
 
+	struct macb_dma_desc	*dummy_desc;
+	unsigned long		dummy_desc_dma;
+
 	const struct device	*dev;
 	struct eth_device	netdev;
 	unsigned short		phy_addr;
@@ -525,6 +529,30 @@ static int macb_phy_init(struct macb_device *macb)
 	return 1;
 }
 
+static int gmac_init_multi_queues(struct macb_device *macb)
+{
+	int i, num_queues = 1;
+	u32 queue_mask;
+
+	/* bit 0 is never set but queue 0 always exists */
+	queue_mask = gem_readl(macb, DCFG6) & 0xff;
+	queue_mask |= 0x1;
+
+	for (i = 1; i < MACB_MAX_QUEUES; i++)
+		if (queue_mask & (1 << i))
+			num_queues++;
+
+	macb->dummy_desc->ctrl = TXBUF_USED;
+	macb->dummy_desc->addr = 0;
+	flush_dcache_range(macb->dummy_desc_dma, macb->dummy_desc_dma +
+			MACB_TX_DUMMY_DMA_DESC_SIZE);
+
+	for (i = 1; i < num_queues; i++)
+		gem_writel_queue_TBQP(macb, macb->dummy_desc_dma, i - 1);
+
+	return 0;
+}
+
 static int macb_init(struct eth_device *netdev, bd_t *bd)
 {
 	struct macb_device *macb = to_macb(netdev);
@@ -565,6 +593,9 @@ static int macb_init(struct eth_device *netdev, bd_t *bd)
 	macb_writel(macb, TBQP, macb->tx_ring_dma);
 
 	if (macb_is_gem(macb)) {
+		/* Check the multi queue and initialize the queue for tx */
+		gmac_init_multi_queues(macb);
+
 		/*
 		 * When the GMAC IP with GE feature, this bit is used to
 		 * select interface between RGMII and GMII.
@@ -712,6 +743,8 @@ int macb_eth_initialize(int id, void *regs, unsigned int phy_addr)
 					   &macb->rx_ring_dma);
 	macb->tx_ring = dma_alloc_coherent(MACB_TX_DMA_DESC_SIZE,
 					   &macb->tx_ring_dma);
+	macb->dummy_desc = dma_alloc_coherent(MACB_TX_DUMMY_DMA_DESC_SIZE,
+					   &macb->dummy_desc_dma);
 
 	/* TODO: we need check the rx/tx_ring_dma is dcache line aligned */
 

drivers/net/macb.h

@@ -60,6 +60,13 @@
 
 /* GEM specific register offsets */
 #define GEM_DCFG1				0x0280
+#define GEM_DCFG6				0x0294
+
+#define MACB_MAX_QUEUES				8
+
+/* GEM specific multi queues register offset */
+/* hw_q can be 0~7 */
+#define GEM_TBQP(hw_q)				(0x0440 + ((hw_q) << 2))
 
 /* Bitfields in NCR */
 #define MACB_LB_OFFSET				0
@@ -309,5 +316,7 @@
 	readl((port)->regs + GEM_##reg)
 #define gem_writel(port, reg, value)			\
 	writel((value), (port)->regs + GEM_##reg)
+#define gem_writel_queue_TBQP(port, value, queue_num)	\
+	writel((value), (port)->regs + GEM_TBQP(queue_num))
 
 #endif /* __DRIVERS_MACB_H__ */

drivers/net/phy/broadcom.c

@@ -137,6 +137,24 @@ static int bcm5482_config(struct phy_device *phydev)
 	return 0;
 }
 
+static int bcm_cygnus_startup(struct phy_device *phydev)
+{
+	/* Read the Status (2x to make sure link is right) */
+	genphy_update_link(phydev);
+	genphy_parse_link(phydev);
+
+	return 0;
+}
+
+static int bcm_cygnus_config(struct phy_device *phydev)
+{
+	genphy_config_aneg(phydev);
+
+	phy_reset(phydev);
+
+	return 0;
+}
+
 /*
  * Find out if PHY is in copper or serdes mode by looking at Expansion Reg
  * 0x42 - "Operating Mode Status Register"
@@ -264,11 +282,22 @@ static struct phy_driver BCM5482S_driver = {
 	.shutdown = &genphy_shutdown,
 };
 
+static struct phy_driver BCM_CYGNUS_driver = {
+	.name = "Broadcom CYGNUS GPHY",
+	.uid = 0xae025200,
+	.mask = 0xfffff0,
+	.features = PHY_GBIT_FEATURES,
+	.config = &bcm_cygnus_config,
+	.startup = &bcm_cygnus_startup,
+	.shutdown = &genphy_shutdown,
+};
+
 int phy_broadcom_init(void)
 {
 	phy_register(&BCM5482S_driver);
 	phy_register(&BCM5464S_driver);
 	phy_register(&BCM5461S_driver);
+	phy_register(&BCM_CYGNUS_driver);
 
 	return 0;
 }

drivers/net/phy/marvell.c

@@ -303,30 +303,58 @@ static int m88e1518_config(struct phy_device *phydev)
 	 * As per Marvell Release Notes - Alaska 88E1510/88E1518/88E1512
 	 * /88E1514 Rev A0, Errata Section 3.1
 	 */
+
+	/* EEE initialization */
+	phy_write(phydev, MDIO_DEVAD_NONE, 22, 0x00ff);
+	phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x214B);
+	phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x2144);
+	phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x0C28);
+	phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x2146);
+	phy_write(phydev, MDIO_DEVAD_NONE, 17, 0xB233);
+	phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x214D);
+	phy_write(phydev, MDIO_DEVAD_NONE, 17, 0xCC0C);
+	phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x2159);
+	phy_write(phydev, MDIO_DEVAD_NONE, 22, 0x0000);
+
+	/* SGMII-to-Copper mode initialization */
 	if (phydev->interface == PHY_INTERFACE_MODE_SGMII) {
-		phy_write(phydev, MDIO_DEVAD_NONE, 22, 0x00ff);	/* page 0xff */
-		phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x214B);
-		phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x2144);
-		phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x0C28);
-		phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x2146);
-		phy_write(phydev, MDIO_DEVAD_NONE, 17, 0xB233);
-		phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x214D);
-		phy_write(phydev, MDIO_DEVAD_NONE, 17, 0xCC0C);
-		phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x2159);
-		phy_write(phydev, MDIO_DEVAD_NONE, 22, 0x0000);	/* reg page 0 */
-		phy_write(phydev, MDIO_DEVAD_NONE, 22, 18);    /* reg page 18 */
-		/* Write HWCFG_MODE = SGMII to Copper */
+		/* Select page 18 */
+		phy_write(phydev, MDIO_DEVAD_NONE, 22, 18);
+
+		/* In reg 20, write MODE[2:0] = 0x1 (SGMII to Copper) */
 		m88e1518_phy_writebits(phydev, 20, 0, 3, 1);
 
-		/* Phy reset */
+		/* PHY reset is necessary after changing MODE[2:0] */
 		m88e1518_phy_writebits(phydev, 20, 15, 1, 1);
-		phy_write(phydev, MDIO_DEVAD_NONE, 22, 0);     /* reg page 18 */
+
+		/* Reset page selection */
+		phy_write(phydev, MDIO_DEVAD_NONE, 22, 0);
+
 		udelay(100);
 	}
 
 	return m88e1111s_config(phydev);
 }
 
+/* Marvell 88E1510 */
+static int m88e1510_config(struct phy_device *phydev)
+{
+	/* Select page 3 */
+	phy_write(phydev, MDIO_DEVAD_NONE, 22, 3);
+
+	/* Enable INTn output on LED[2] */
+	m88e1518_phy_writebits(phydev, 18, 7, 1, 1);
+
+	/* Configure LEDs */
+	m88e1518_phy_writebits(phydev, 16, 0, 4, 3); /* LED[0]:0011 (ACT) */
+	m88e1518_phy_writebits(phydev, 16, 4, 4, 6); /* LED[1]:0110 (LINK) */
+
+	/* Reset page selection */
+	phy_write(phydev, MDIO_DEVAD_NONE, 22, 0);
+
+	return m88e1518_config(phydev);
+}
+
 /* Marvell 88E1118 */
 static int m88e1118_config(struct phy_device *phydev)
 {
@@ -539,6 +567,16 @@ static struct phy_driver M88E1149S_driver = {
 	.shutdown = &genphy_shutdown,
 };
 
+static struct phy_driver M88E1510_driver = {
+	.name = "Marvell 88E1510",
+	.uid = 0x1410dd0,
+	.mask = 0xffffff0,
+	.features = PHY_GBIT_FEATURES,
+	.config = &m88e1510_config,
+	.startup = &m88e1011s_startup,
+	.shutdown = &genphy_shutdown,
+};
+
 static struct phy_driver M88E1518_driver = {
 	.name = "Marvell 88E1518",
 	.uid = 0x1410dd1,
@@ -569,6 +607,7 @@ int phy_marvell_init(void)
 	phy_register(&M88E1118R_driver);
 	phy_register(&M88E1111S_driver);
 	phy_register(&M88E1011S_driver);
+	phy_register(&M88E1510_driver);
 	phy_register(&M88E1518_driver);
 
 	return 0;

drivers/net/phy/phy.c

@@ -554,7 +554,7 @@ static struct phy_driver *get_phy_driver(struct phy_device *phydev,
 }
 
 static struct phy_device *phy_device_create(struct mii_dev *bus, int addr,
-					    int phy_id,
+					    u32 phy_id,
 					    phy_interface_t interface)
 {
 	struct phy_device *dev;
@@ -763,11 +763,13 @@ struct phy_device *phy_find_by_mask(struct mii_dev *bus, unsigned phy_mask,
 		phy_interface_t interface)
 {
 	/* Reset the bus */
-	if (bus->reset)
+	if (bus->reset) {
 		bus->reset(bus);
 
-	/* Wait 15ms to make sure the PHY has come out of hard reset */
-	udelay(15000);
+		/* Wait 15ms to make sure the PHY has come out of hard reset */
+		udelay(15000);
+	}
+
 	return get_phy_device_by_mask(bus, phy_mask, interface);
 }
 

drivers/net/phy/realtek.c

@@ -41,6 +41,7 @@
 
 #define MIIM_RTL8211F_PAGE_SELECT      0x1f
 #define MIIM_RTL8211F_TX_DELAY		0x100
+#define MIIM_RTL8211F_LCR		0x10
 
 /* RealTek RTL8211x */
 static int rtl8211x_config(struct phy_device *phydev)
@@ -79,6 +80,13 @@ static int rtl8211f_config(struct phy_device *phydev)
 			  MIIM_RTL8211F_PAGE_SELECT, 0x0);
 	}
 
+	/* Set green LED for Link, yellow LED for Active */
+	phy_write(phydev, MDIO_DEVAD_NONE,
+		  MIIM_RTL8211F_PAGE_SELECT, 0xd04);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x10, 0x617f);
+	phy_write(phydev, MDIO_DEVAD_NONE,
+		  MIIM_RTL8211F_PAGE_SELECT, 0x0);
+
 	genphy_config_aneg(phydev);
 
 	return 0;

net/tftp.c

@@ -249,6 +249,8 @@ static void show_block_marker(void)
 	if (tftp_tsize) {
 		ulong pos = tftp_cur_block * tftp_block_size +
 			tftp_block_wrap_offset;
+		if (pos > tftp_tsize)
+			pos = tftp_tsize;
 
 		while (tftp_tsize_num_hash < pos * 50 / tftp_tsize) {
 			putc('#');