board/freescale:Remove use of CONFIG_SPL_NAND_MINIMAL

CONFIG_SPL_NAND_MINIMAL should not be used as it was defined for temporary
review purpose.

So, use CONFIG_SPL_NAND_BOOT config.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>

README

@@ -3267,6 +3267,9 @@ FIT uImage format:
 		Defines the size and behavior of the NAND that SPL uses
 		to read U-Boot
 
+		CONFIG_SPL_NAND_BOOT
+		Add support NAND boot
+
 		CONFIG_SYS_NAND_U_BOOT_OFFS
 		Location in NAND to read U-Boot from
 

board/freescale/bsc9131rdb/tlb.c

@@ -30,7 +30,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
 	SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 		      0, 0, BOOKE_PAGESZ_4K, 1),
-#ifdef CONFIG_SPL_NAND_MINIMAL
+#ifdef CONFIG_SPL_NAND_BOOT
 	SET_TLB_ENTRY(1, 0xffffe000, 0xffffe000,
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 		      0, 10, BOOKE_PAGESZ_4K, 1),

board/freescale/bsc9132qds/tlb.c

@@ -30,7 +30,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
 	SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 		      0, 0, BOOKE_PAGESZ_4K, 1),
-#ifdef CONFIG_SPL_NAND_MINIMAL
+#ifdef CONFIG_SPL_NAND_BOOT
 	SET_TLB_ENTRY(1, 0xffffe000, 0xffffe000,
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 		      0, 10, BOOKE_PAGESZ_4K, 1),

board/freescale/p1010rdb/tlb.c

@@ -30,7 +30,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
 	SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 		      0, 0, BOOKE_PAGESZ_4K, 1),
-#ifdef CONFIG_SPL_NAND_MINIMAL
+#ifdef CONFIG_SPL_NAND_BOOT
 	SET_TLB_ENTRY(1, 0xffffe000, 0xffffe000,
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 		      0, 10, BOOKE_PAGESZ_4K, 1),

include/configs/BSC9131RDB.h

@@ -29,7 +29,7 @@
 #define CONFIG_SPL_INIT_MINIMAL
 #define CONFIG_SPL_SERIAL_SUPPORT
 #define CONFIG_SPL_NAND_SUPPORT
-#define CONFIG_SPL_NAND_MINIMAL
+#define CONFIG_SPL_NAND_BOOT
 #define CONFIG_SPL_FLUSH_IMAGE
 #define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
 

include/configs/BSC9132QDS.h

@@ -38,7 +38,7 @@
 #define CONFIG_SPL_INIT_MINIMAL
 #define CONFIG_SPL_SERIAL_SUPPORT
 #define CONFIG_SPL_NAND_SUPPORT
-#define CONFIG_SPL_NAND_MINIMAL
+#define CONFIG_SPL_NAND_BOOT
 #define CONFIG_SPL_FLUSH_IMAGE
 #define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
 

include/configs/P1010RDB.h

@@ -37,7 +37,7 @@
 #define CONFIG_SPL_INIT_MINIMAL
 #define CONFIG_SPL_SERIAL_SUPPORT
 #define CONFIG_SPL_NAND_SUPPORT
-#define CONFIG_SPL_NAND_MINIMAL
+#define CONFIG_SPL_NAND_BOOT
 #define CONFIG_SPL_FLUSH_IMAGE
 #define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"