board: axs10x switch serial port and Ethernet to driver model

With this change Synopsys DesignWare SDP board is switched to driver
model for both serial port (serial_dw) and Ethernet (Designware GMAC).

This simplifies include/configs/axs101.h and allows for reuse of Linux's
Device Tree description.

For simplicity Linux's .dts files are not blindly copied but only very
few extracts of them are really used (those that are supported in U-Boot
at the moment).

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>

arch/arc/dts/Makefile

@@ -2,6 +2,7 @@
 # SPDX-License-Identifier:	GPL-2.0+
 #
 
+dtb-$(CONFIG_TARGET_AXS101) +=  axs10x.dtb
 dtb-$(CONFIG_TARGET_ARCANGEL4) +=  arcangel4.dtb
 dtb-$(CONFIG_TARGET_TB100) +=  abilis_tb100.dtb
 

arch/arc/dts/axs10x.dts

@@ -0,0 +1,45 @@
+/*
+ * Copyright (C) 2015 Synopsys, Inc. All rights reserved.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+/dts-v1/;
+
+#include "skeleton.dtsi"
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	aliases {
+		console = &uart0;
+	};
+
+	clocks {
+		apbclk: apbclk {
+			compatible = "fixed-clock";
+			clock-frequency = <50000000>;
+			#clock-cells = <0>;
+		};
+	};
+
+	uart0: serial0@e0022000 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0xe0022000 0x1000>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+	};
+
+	ethernet@e0018000 {
+		#interrupt-cells = <1>;
+		compatible = "altr,socfpga-stmmac";
+		reg = < 0xe0018000 0x2000 >;
+		interrupts = < 25 >;
+		interrupt-names = "macirq";
+		phy-mode = "gmii";
+		snps,pbl = < 32 >;
+		clocks = <&apbclk>;
+		clock-names = "stmmaceth";
+		max-speed = <100>;
+	};
+};

board/synopsys/axs101/axs101.c

@@ -7,8 +7,6 @@
 #include <common.h>
 #include <dwmmc.h>
 #include <malloc.h>
-#include <netdev.h>
-#include <phy.h>
 #include "axs10x.h"
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -35,16 +33,6 @@ int board_mmc_init(bd_t *bis)
 	return 0;
 }
 
-int board_eth_init(bd_t *bis)
-{
-	if (designware_initialize(ARC_DWGMAC_BASE,
-				  PHY_INTERFACE_MODE_RGMII) >= 0)
-		return 1;
-
-	return 0;
-}
-
-
 #define AXS_MB_CREG	0xE0011000
 
 int board_early_init_f(void)

configs/axs101_defconfig

@@ -1,12 +1,21 @@
 CONFIG_ARC=y
 CONFIG_SYS_DCACHE_OFF=y
 CONFIG_ARC_CACHE_LINE_SHIFT=5
+CONFIG_DM_SERIAL=y
 CONFIG_SYS_CLK_FREQ=750000000
 CONFIG_SYS_TEXT_BASE=0x81000000
+CONFIG_DEFAULT_DEVICE_TREE="axs10x"
 CONFIG_SYS_PROMPT="AXS# "
 # CONFIG_CMD_IMLS is not set
 # CONFIG_CMD_FLASH is not set
 # CONFIG_CMD_SETEXPR is not set
-CONFIG_NETDEVICES=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_PING=y
+CONFIG_OF_CONTROL=y
+CONFIG_OF_EMBED=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_DM_ETH=y
 CONFIG_ETH_DESIGNWARE=y
 CONFIG_USE_PRIVATE_LIBGCC=y

configs/axs103_defconfig

@@ -1,11 +1,20 @@
 CONFIG_ARC=y
 CONFIG_ISA_ARCV2=y
+CONFIG_DM_SERIAL=y
 CONFIG_SYS_CLK_FREQ=50000000
 CONFIG_SYS_TEXT_BASE=0x81000000
+CONFIG_DEFAULT_DEVICE_TREE="axs10x"
 CONFIG_SYS_PROMPT="AXS# "
 # CONFIG_CMD_IMLS is not set
 # CONFIG_CMD_FLASH is not set
 # CONFIG_CMD_SETEXPR is not set
-CONFIG_NETDEVICES=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_PING=y
+CONFIG_OF_CONTROL=y
+CONFIG_OF_EMBED=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_DM_ETH=y
 CONFIG_ETH_DESIGNWARE=y
 CONFIG_USE_PRIVATE_LIBGCC=y

include/configs/axs101.h

@@ -39,6 +39,8 @@
 #define CONFIG_BOARD_TYPES
 #define CONFIG_BOARD_EARLY_INIT_F
 
+#define CONFIG_OF_LIBFDT
+
 /*
  * NAND Flash configuration
  */
@@ -48,28 +50,14 @@
 
 /*
  * UART configuration
- *
- * CONFIG_CONS_INDEX = 1 - Debug UART
- * CONFIG_CONS_INDEX = 4 - FPGA UART connected to FTDI/USB
  */
-#define CONFIG_CONS_INDEX		4
+#define CONFIG_DW_SERIAL
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	-4
-#if (CONFIG_CONS_INDEX == 1)
-	/* Debug UART */
-#	define CONFIG_SYS_NS16550_CLK		33333000
-#else
-	/* FPGA UARTs use different clock */
-#	define CONFIG_SYS_NS16550_CLK		33333333
-#endif
-#define CONFIG_SYS_NS16550_COM1		(ARC_APB_PERIPHERAL_BASE + 0x5000)
-#define CONFIG_SYS_NS16550_COM2		(ARC_FPGA_PERIPHERAL_BASE + 0x20000)
-#define CONFIG_SYS_NS16550_COM3		(ARC_FPGA_PERIPHERAL_BASE + 0x21000)
-#define CONFIG_SYS_NS16550_COM4		(ARC_FPGA_PERIPHERAL_BASE + 0x22000)
+#define CONFIG_SYS_NS16550_CLK		33333333
 #define CONFIG_SYS_NS16550_MEM32
-
 #define CONFIG_BAUDRATE			115200
+
 /*
  * I2C configuration
  */
@@ -119,18 +107,11 @@
 #define CONFIG_DW_AUTONEG
 
 /*
- * Command line configuration
+ * Commands still not supported in Kconfig
  */
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
 #define CONFIG_CMD_MMC
 #define CONFIG_CMD_NAND
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_RARP
-
-#define CONFIG_OF_LIBFDT
 
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_SYS_MAXARGS		16