imx: Add error checking to setup_i2c()

Since this function can fail, check its return value.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>

arch/arm/imx-common/i2c-mxv7.c

@@ -69,15 +69,29 @@ static void * const i2c_bases[] = {
 };
 
 /* i2c_index can be from 0 - 2 */
-void setup_i2c(unsigned i2c_index, int speed, int slave_addr,
-		struct i2c_pads_info *p)
+int setup_i2c(unsigned i2c_index, int speed, int slave_addr,
+	      struct i2c_pads_info *p)
 {
+	int ret;
+
 	if (i2c_index >= ARRAY_SIZE(i2c_bases))
-		return;
+		return -EINVAL;
 	/* Enable i2c clock */
-	enable_i2c_clk(1, i2c_index);
+	ret = enable_i2c_clk(1, i2c_index);
+	if (ret)
+		goto err_clk;
+
 	/* Make sure bus is idle */
-	force_idle_bus(p);
+	ret = force_idle_bus(p);
+	if (ret)
+		goto err_idle;
+
 	bus_i2c_init(i2c_bases[i2c_index], speed, slave_addr,
 			force_idle_bus, p);
+
+	return 0;
+
+err_idle:
+err_clk:
+	return ret;
 }

arch/arm/include/asm/imx-common/mxc_i2c.h

@@ -52,8 +52,8 @@ struct i2c_pads_info {
 					&mx6q_##name : &mx6s_##name
 #endif
 
-void setup_i2c(unsigned i2c_index, int speed, int slave_addr,
-		struct i2c_pads_info *p);
+int setup_i2c(unsigned i2c_index, int speed, int slave_addr,
+	      struct i2c_pads_info *p);
 void bus_i2c_init(void *base, int speed, int slave_addr,
 		int (*idle_bus_fn)(void *p), void *p);
 int bus_i2c_read(void *base, uchar chip, uint addr, int alen, uchar *buf,

board/compulab/cm_fx6/cm_fx6.c

@@ -141,14 +141,36 @@ I2C_PADS(i2c2_pads,
 	 IMX_GPIO_NR(1, 6));
 
 
-static void cm_fx6_setup_i2c(void)
+static int cm_fx6_setup_one_i2c(int busnum, struct i2c_pads_info *pads)
 {
-	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, I2C_PADS_INFO(i2c0_pads));
-	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, I2C_PADS_INFO(i2c1_pads));
-	setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, I2C_PADS_INFO(i2c2_pads));
+	int ret;
+
+	ret = setup_i2c(busnum, CONFIG_SYS_I2C_SPEED, 0x7f, pads);
+	if (ret)
+		printf("Warning: I2C%d setup failed: %d\n", busnum, ret);
+
+	return ret;
+}
+
+static int cm_fx6_setup_i2c(void)
+{
+	int ret = 0, err;
+
+	/* i2c<x>_pads are wierd macro variables; we can't use an array */
+	err = cm_fx6_setup_one_i2c(0, I2C_PADS_INFO(i2c0_pads));
+	if (err)
+		ret = err;
+	err = cm_fx6_setup_one_i2c(1, I2C_PADS_INFO(i2c1_pads));
+	if (err)
+		ret = err;
+	err = cm_fx6_setup_one_i2c(2, I2C_PADS_INFO(i2c2_pads));
+	if (err)
+		ret = err;
+
+	return ret;
 }
 #else
-static void cm_fx6_setup_i2c(void) { }
+static int cm_fx6_setup_i2c(void) { return 0; }
 #endif
 
 #ifdef CONFIG_USB_EHCI_MX6
@@ -409,9 +431,15 @@ void ft_board_setup(void *blob, bd_t *bd)
 
 int board_init(void)
 {
+	int ret;
+
 	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
 	cm_fx6_setup_gpmi_nand();
-	cm_fx6_setup_i2c();
+
+	/* Warn on failure but do not abort boot */
+	ret = cm_fx6_setup_i2c();
+	if (ret)
+		printf("Warning: I2C setup failed: %d\n", ret);
 
 	return 0;
 }