Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq

README

@@ -3869,7 +3869,15 @@ Configuration Settings:
 		Scratch address used by the alternate memory test
 		You only need to set this if address zero isn't writeable
 
-- CONFIG_SYS_MEM_TOP_HIDE (PPC only):
+- CONFIG_SYS_MEM_RESERVE_SECURE
+		If defined, the size of CONFIG_SYS_MEM_RESERVE_SECURE memory
+		is substracted from total RAM and won't be reported to OS.
+		This memory can be used as secure memory. A variable
+		gd->secure_ram is used to track the location. In systems
+		the RAM base is not zero, or RAM is divided into banks,
+		this variable needs to be recalcuated to get the address.
+
+- CONFIG_SYS_MEM_TOP_HIDE:
 		If CONFIG_SYS_MEM_TOP_HIDE is defined in the board config header,
 		this specified memory area will get subtracted from the top
 		(end) of RAM and won't get "touched" at all by U-Boot. By
@@ -5048,8 +5056,8 @@ This firmware often needs to be loaded during U-Boot booting.
 - CONFIG_SYS_DEBUG_SERVER_DRAM_BLOCK_MIN_SIZE
 	Define minimum DDR size required for debug server image
 
-- CONFIG_SYS_MEM_TOP_HIDE_MIN
-	Define minimum DDR size to be hided from top of the DDR memory
+- CONFIG_SYS_MC_RSV_MEM_ALIGN
+	Define alignment of reserved memory MC requires
 
 Reproducible builds
 -------------------

arch/arm/cpu/armv7/ls102xa/Makefile

@@ -8,6 +8,7 @@ obj-y	+= cpu.o
 obj-y	+= clock.o
 obj-y	+= timer.o
 obj-y	+= fsl_epu.o
+obj-y	+= soc.o
 
 obj-$(CONFIG_SCSI_AHCI_PLAT) += ls102xa_sata.o
 obj-$(CONFIG_OF_LIBFDT) += fdt.o

arch/arm/cpu/armv7/ls102xa/cpu.c

@@ -218,6 +218,14 @@ void enable_caches(void)
 }
 #endif /* #ifndef CONFIG_SYS_DCACHE_OFF */
 
+
+uint get_svr(void)
+{
+	struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
+
+	return in_be32(&gur->svr);
+}
+
 #if defined(CONFIG_DISPLAY_CPUINFO)
 int print_cpuinfo(void)
 {

arch/arm/cpu/armv7/ls102xa/soc.c

@@ -0,0 +1,90 @@
+/*
+ * Copyright 2015 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/clock.h>
+#include <asm/io.h>
+#include <asm/arch/immap_ls102xa.h>
+#include <asm/arch/ls102xa_soc.h>
+
+unsigned int get_soc_major_rev(void)
+{
+	struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
+	unsigned int svr, major;
+
+	svr = in_be32(&gur->svr);
+	major = SVR_MAJ(svr);
+
+	return major;
+}
+
+int arch_soc_init(void)
+{
+	struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
+	struct ccsr_cci400 *cci = (struct ccsr_cci400 *)CONFIG_SYS_CCI400_ADDR;
+	unsigned int major;
+
+#ifdef CONFIG_FSL_QSPI
+	out_be32(&scfg->qspi_cfg, SCFG_QSPI_CLKSEL);
+#endif
+
+#ifdef CONFIG_FSL_DCU_FB
+	out_be32(&scfg->pixclkcr, SCFG_PIXCLKCR_PXCKEN);
+#endif
+
+	/* Configure Little endian for SAI, ASRC and SPDIF */
+	out_be32(&scfg->endiancr, SCFG_ENDIANCR_LE);
+
+	/*
+	 * Enable snoop requests and DVM message requests for
+	 * All the slave insterfaces.
+	 */
+	out_le32(&cci->slave[0].snoop_ctrl,
+		 CCI400_DVM_MESSAGE_REQ_EN | CCI400_SNOOP_REQ_EN);
+	out_le32(&cci->slave[1].snoop_ctrl,
+		 CCI400_DVM_MESSAGE_REQ_EN | CCI400_SNOOP_REQ_EN);
+	out_le32(&cci->slave[2].snoop_ctrl,
+		 CCI400_DVM_MESSAGE_REQ_EN | CCI400_SNOOP_REQ_EN);
+	out_le32(&cci->slave[4].snoop_ctrl,
+		 CCI400_DVM_MESSAGE_REQ_EN | CCI400_SNOOP_REQ_EN);
+
+	major = get_soc_major_rev();
+	if (major == SOC_MAJOR_VER_1_0) {
+		/*
+		 * Set CCI-400 Slave interface S1, S2 Shareable Override
+		 * Register All transactions are treated as non-shareable
+		 */
+		out_le32(&cci->slave[1].sha_ord, CCI400_SHAORD_NON_SHAREABLE);
+		out_le32(&cci->slave[2].sha_ord, CCI400_SHAORD_NON_SHAREABLE);
+
+		/* Workaround for the issue that DDR could not respond to
+		 * barrier transaction which is generated by executing DSB/ISB
+		 * instruction. Set CCI-400 control override register to
+		 * terminate the barrier transaction. After DDR is initialized,
+		 * allow barrier transaction to DDR again */
+		out_le32(&cci->ctrl_ord, CCI400_CTRLORD_TERM_BARRIER);
+	}
+
+	/* Enable all the snoop signal for various masters */
+	out_be32(&scfg->snpcnfgcr, SCFG_SNPCNFGCR_SEC_RD_WR |
+				SCFG_SNPCNFGCR_DCU_RD_WR |
+				SCFG_SNPCNFGCR_SATA_RD_WR |
+				SCFG_SNPCNFGCR_USB3_RD_WR |
+				SCFG_SNPCNFGCR_DBG_RD_WR |
+				SCFG_SNPCNFGCR_EDMA_SNP);
+
+	/*
+	 * Memory controller require a register write before being enabled.
+	 * Affects: DDR
+	 * Register: EDDRTQCFG
+	 * Description: Memory controller performance is not optimal with
+	 *		default internal target queue register values.
+	 * Workaround: Write a value of 63b2_0042h to address: 157_020Ch.
+	 */
+	out_be32(&scfg->eddrtqcfg, 0x63b20042);
+
+	return 0;
+}

arch/arm/cpu/armv8/fsl-layerscape/cpu.c

@@ -206,11 +206,65 @@ static inline void early_mmu_setup(void)
 	set_sctlr(get_sctlr() | CR_M);
 }
 
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+/*
+ * Called from final mmu setup. The phys_addr is new, non-existing
+ * address. A new sub table is created @level2_table_secure to cover
+ * size of CONFIG_SYS_MEM_RESERVE_SECURE memory.
+ */
+static inline int final_secure_ddr(u64 *level0_table,
+				   u64 *level2_table_secure,
+				   phys_addr_t phys_addr)
+{
+	int ret = -EINVAL;
+	struct table_info table = {};
+	struct sys_mmu_table ddr_entry = {
+		0, 0, BLOCK_SIZE_L1, MT_NORMAL,
+		PMD_SECT_OUTER_SHARE | PMD_SECT_NS
+	};
+	u64 index;
+
+	/* Need to create a new table */
+	ddr_entry.virt_addr = phys_addr & ~(BLOCK_SIZE_L1 - 1);
+	ddr_entry.phys_addr = phys_addr & ~(BLOCK_SIZE_L1 - 1);
+	ret = find_table(&ddr_entry, &table, level0_table);
+	if (ret)
+		return ret;
+	index = (ddr_entry.virt_addr - table.table_base) >> SECTION_SHIFT_L1;
+	set_pgtable_table(table.ptr, index, level2_table_secure);
+	table.ptr = level2_table_secure;
+	table.table_base = ddr_entry.virt_addr;
+	table.entry_size = BLOCK_SIZE_L2;
+	ret = set_block_entry(&ddr_entry, &table);
+	if (ret) {
+		printf("MMU error: could not fill non-secure ddr block entries\n");
+		return ret;
+	}
+	ddr_entry.virt_addr = phys_addr;
+	ddr_entry.phys_addr = phys_addr;
+	ddr_entry.size = CONFIG_SYS_MEM_RESERVE_SECURE;
+	ddr_entry.attribute = PMD_SECT_OUTER_SHARE;
+	ret = find_table(&ddr_entry, &table, level0_table);
+	if (ret) {
+		printf("MMU error: could not find secure ddr table\n");
+		return ret;
+	}
+	ret = set_block_entry(&ddr_entry, &table);
+	if (ret)
+		printf("MMU error: could not set secure ddr block entry\n");
+
+	return ret;
+}
+#endif
+
 /*
  * The final tables look similar to early tables, but different in detail.
  * These tables are in DRAM. Sub tables are added to enable cache for
  * QBMan and OCRAM.
  *
+ * Put the MMU table in secure memory if gd->secure_ram is valid.
+ * OCRAM will be not used for this purpose so gd->secure_ram can't be 0.
+ *
  * Level 1 table 0 contains 512 entries for each 1GB from 0 to 512GB.
  * Level 1 table 1 contains 512 entries for each 1GB from 512GB to 1TB.
  * Level 2 table 0 contains 512 entries for each 2MB from 0 to 1GB.
@@ -223,18 +277,40 @@ static inline void early_mmu_setup(void)
  */
 static inline void final_mmu_setup(void)
 {
-	unsigned int el, i;
+	unsigned int el = current_el();
+	unsigned int i;
 	u64 *level0_table = (u64 *)gd->arch.tlb_addr;
-	u64 *level1_table0 = (u64 *)(gd->arch.tlb_addr + 0x1000);
-	u64 *level1_table1 = (u64 *)(gd->arch.tlb_addr + 0x2000);
-	u64 *level2_table0 = (u64 *)(gd->arch.tlb_addr + 0x3000);
-#ifdef CONFIG_FSL_LSCH3
-	u64 *level2_table1 = (u64 *)(gd->arch.tlb_addr + 0x4000);
-#elif defined(CONFIG_FSL_LSCH2)
-	u64 *level2_table1 = (u64 *)(gd->arch.tlb_addr + 0x4000);
-	u64 *level2_table2 = (u64 *)(gd->arch.tlb_addr + 0x5000);
+	u64 *level1_table0;
+	u64 *level1_table1;
+	u64 *level2_table0;
+	u64 *level2_table1;
+#ifdef CONFIG_FSL_LSCH2
+	u64 *level2_table2;
 #endif
-	struct table_info table = {level0_table, 0, BLOCK_SIZE_L0};
+	struct table_info table = {NULL, 0, BLOCK_SIZE_L0};
+
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+	u64 *level2_table_secure;
+
+	if (el == 3) {
+		/*
+		 * Only use gd->secure_ram if the address is recalculated
+		 * Align to 4KB for MMU table
+		 */
+		if (gd->secure_ram & MEM_RESERVE_SECURE_MAINTAINED)
+			level0_table = (u64 *)(gd->secure_ram & ~0xfff);
+		else
+			printf("MMU warning: gd->secure_ram is not maintained, disabled.\n");
+	}
+#endif
+	level1_table0 = level0_table + 512;
+	level1_table1 = level1_table0 + 512;
+	level2_table0 = level1_table1 + 512;
+	level2_table1 = level2_table0 + 512;
+#ifdef CONFIG_FSL_LSCH2
+	level2_table2 = level2_table1 + 512;
+#endif
+	table.ptr = level0_table;
 
 	/* Invalidate all table entries */
 	memset(level0_table, 0, PGTABLE_SIZE);
@@ -269,17 +345,34 @@ static inline void final_mmu_setup(void)
 			       &final_mmu_table[i]);
 		}
 	}
+	/* Set the secure memory to secure in MMU */
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+	if (el == 3 && gd->secure_ram & MEM_RESERVE_SECURE_MAINTAINED) {
+#ifdef CONFIG_FSL_LSCH3
+		level2_table_secure = level2_table1 + 512;
+#elif defined(CONFIG_FSL_LSCH2)
+		level2_table_secure = level2_table2 + 512;
+#endif
+		if (!final_secure_ddr(level0_table,
+				      level2_table_secure,
+				      gd->secure_ram & ~0x3)) {
+			gd->secure_ram |= MEM_RESERVE_SECURE_SECURED;
+			debug("Now MMU table is in secured memory at 0x%llx\n",
+			      gd->secure_ram & ~0x3);
+		} else {
+			printf("MMU warning: Failed to secure DDR\n");
+		}
+	}
+#endif
 
 	/* flush new MMU table */
-	flush_dcache_range(gd->arch.tlb_addr,
-			   gd->arch.tlb_addr + gd->arch.tlb_size);
+	flush_dcache_range((ulong)level0_table,
+			   (ulong)level0_table + gd->arch.tlb_size);
 
 #ifdef CONFIG_SYS_DPAA_FMAN
 	flush_dcache_all();
 #endif
 	/* point TTBR to the new table */
-	el = current_el();
-
 	set_ttbr_tcr_mair(el, (u64)level0_table, LAYERSCAPE_TCR_FINAL,
 			  MEMORY_ATTRIBUTES);
 	/*
@@ -543,3 +636,24 @@ void reset_cpu(ulong addr)
 	val |= 0x02;
 	scfg_out32(rstcr, val);
 }
+
+phys_size_t board_reserve_ram_top(phys_size_t ram_size)
+{
+	phys_size_t ram_top = ram_size;
+
+#ifdef CONFIG_SYS_MEM_TOP_HIDE
+#error CONFIG_SYS_MEM_TOP_HIDE not to be used together with this function
+#endif
+/* Carve the Debug Server private DRAM block from the end of DRAM */
+#ifdef CONFIG_FSL_DEBUG_SERVER
+	ram_top -= debug_server_get_dram_block_size();
+#endif
+
+/* Carve the MC private DRAM block from the end of DRAM */
+#ifdef CONFIG_FSL_MC_ENET
+	ram_top -= mc_get_dram_block_size();
+	ram_top &= ~(CONFIG_SYS_MC_RSV_MEM_ALIGN - 1);
+#endif
+
+	return ram_top;
+}

arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch2_serdes.c

@@ -86,7 +86,7 @@ void serdes_init(u32 sd, u32 sd_addr, u32 sd_prctl_mask, u32 sd_prctl_shift,
 	u32 cfg;
 	int lane;
 
-	memset(serdes_prtcl_map, 0, sizeof(serdes_prtcl_map));
+	memset(serdes_prtcl_map, 0, sizeof(u8) * SERDES_PRCTL_COUNT);
 
 	cfg = gur_in32(&gur->rcwsr[4]) & sd_prctl_mask;
 	cfg >>= sd_prctl_shift;

arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch3_serdes.c

@@ -79,7 +79,7 @@ void serdes_init(u32 sd, u32 sd_addr, u32 sd_prctl_mask, u32 sd_prctl_shift,
 	u32 cfg;
 	int lane;
 
-	memset(serdes_prtcl_map, 0, sizeof(serdes_prtcl_map));
+	memset(serdes_prtcl_map, 0, sizeof(u8) * SERDES_PRCTL_COUNT);
 
 	cfg = gur_in32(&gur->rcwsr[28]) & sd_prctl_mask;
 	cfg >>= sd_prctl_shift;

arch/arm/cpu/armv8/fsl-layerscape/soc.c

@@ -6,6 +6,8 @@
 
 #include <common.h>
 #include <fsl_ifc.h>
+#include <ahci.h>
+#include <scsi.h>
 #include <asm/arch/soc.h>
 #include <asm/io.h>
 #include <asm/global_data.h>
@@ -14,6 +16,41 @@
 DECLARE_GLOBAL_DATA_PTR;
 
 #if defined(CONFIG_LS2080A) || defined(CONFIG_LS2085A)
+/*
+ * This erratum requires setting a value to eddrtqcr1 to
+ * optimal the DDR performance.
+ */
+static void erratum_a008336(void)
+{
+	u32 *eddrtqcr1;
+
+#ifdef CONFIG_SYS_FSL_ERRATUM_A008336
+#ifdef CONFIG_SYS_FSL_DCSR_DDR_ADDR
+	eddrtqcr1 = (void *)CONFIG_SYS_FSL_DCSR_DDR_ADDR + 0x800;
+	out_le32(eddrtqcr1, 0x63b30002);
+#endif
+#ifdef CONFIG_SYS_FSL_DCSR_DDR2_ADDR
+	eddrtqcr1 = (void *)CONFIG_SYS_FSL_DCSR_DDR2_ADDR + 0x800;
+	out_le32(eddrtqcr1, 0x63b30002);
+#endif
+#endif
+}
+
+/*
+ * This erratum requires a register write before being Memory
+ * controller 3 being enabled.
+ */
+static void erratum_a008514(void)
+{
+	u32 *eddrtqcr1;
+
+#ifdef CONFIG_SYS_FSL_ERRATUM_A008514
+#ifdef CONFIG_SYS_FSL_DCSR_DDR3_ADDR
+	eddrtqcr1 = (void *)CONFIG_SYS_FSL_DCSR_DDR3_ADDR + 0x800;
+	out_le32(eddrtqcr1, 0x63b20002);
+#endif
+#endif
+}
 #ifdef CONFIG_SYS_FSL_ERRATUM_A009635
 #define PLATFORM_CYCLE_ENV_VAR	"a009635_interval_val"
 
@@ -118,17 +155,61 @@ void fsl_lsch3_early_init_f(void)
 	erratum_rcw_src();
 	init_early_memctl_regs();	/* tighten IFC timing */
 	erratum_a009203();
+	erratum_a008514();
+	erratum_a008336();
+}
+
+#ifdef CONFIG_SCSI_AHCI_PLAT
+int sata_init(void)
+{
+	struct ccsr_ahci __iomem *ccsr_ahci;
+
+	ccsr_ahci  = (void *)CONFIG_SYS_SATA2;
+	out_le32(&ccsr_ahci->ppcfg, AHCI_PORT_PHY_1_CFG);
+	out_le32(&ccsr_ahci->ptc, AHCI_PORT_TRANS_CFG);
+
+	ccsr_ahci  = (void *)CONFIG_SYS_SATA1;
+	out_le32(&ccsr_ahci->ppcfg, AHCI_PORT_PHY_1_CFG);
+	out_le32(&ccsr_ahci->ptc, AHCI_PORT_TRANS_CFG);
+
+	ahci_init((void __iomem *)CONFIG_SYS_SATA1);
+	scsi_scan(0);
+
+	return 0;
 }
+#endif
 
 #elif defined(CONFIG_LS1043A)
+#ifdef CONFIG_SCSI_AHCI_PLAT
+int sata_init(void)
+{
+	struct ccsr_ahci __iomem *ccsr_ahci = (void *)CONFIG_SYS_SATA;
+
+	out_le32(&ccsr_ahci->ppcfg, AHCI_PORT_PHY_1_CFG);
+	out_le32(&ccsr_ahci->pp2c, AHCI_PORT_PHY_2_CFG);
+	out_le32(&ccsr_ahci->pp3c, AHCI_PORT_PHY_3_CFG);
+	out_le32(&ccsr_ahci->ptc, AHCI_PORT_TRANS_CFG);
+
+	ahci_init((void __iomem *)CONFIG_SYS_SATA);
+	scsi_scan(0);
+
+	return 0;
+}
+#endif
+
 void fsl_lsch2_early_init_f(void)
 {
 	struct ccsr_cci400 *cci = (struct ccsr_cci400 *)CONFIG_SYS_CCI400_ADDR;
+	struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
 
 #ifdef CONFIG_FSL_IFC
 	init_early_memctl_regs();	/* tighten IFC timing */
 #endif
 
+	/* Make SEC reads and writes snoopable */
+	setbits_be32(&scfg->snpcnfgcr, SCFG_SNPCNFGCR_SECRDSNP |
+		     SCFG_SNPCNFGCR_SECWRSNP);
+
 	/*
 	 * Enable snoop requests and DVM message requests for
 	 * Slave insterface S4 (A53 core cluster)
@@ -141,6 +222,10 @@ void fsl_lsch2_early_init_f(void)
 #ifdef CONFIG_BOARD_LATE_INIT
 int board_late_init(void)
 {
+#ifdef CONFIG_SCSI_AHCI_PLAT
+	sata_init();
+#endif
+
 	return 0;
 }
 #endif

arch/arm/cpu/armv8/generic_timer.c

@@ -40,3 +40,14 @@ unsigned long timer_read_counter(void)
 #endif
 	return cntpct;
 }
+
+unsigned long usec2ticks(unsigned long usec)
+{
+	ulong ticks;
+	if (usec < 1000)
+		ticks = ((usec * (get_tbclk()/1000)) + 500) / 1000;
+	else
+		ticks = ((usec / 10) * (get_tbclk() / 100000));
+
+	return ticks;
+}

arch/arm/include/asm/arch-fsl-layerscape/config.h

@@ -17,6 +17,12 @@
 #define CONFIG_SYS_FSL_DDR		/* Freescale DDR driver */
 #define CONFIG_SYS_FSL_DDR_VER		FSL_DDR_VER_5_0
 
+/*
+ * Reserve secure memory
+ * To be aligned with MMU block size
+ */
+#define CONFIG_SYS_MEM_RESERVE_SECURE	(2048 * 1024)	/* 2MB */
+
 #if defined(CONFIG_LS2080A) || defined(CONFIG_LS2085A)
 #define CONFIG_MAX_CPUS				16
 #define CONFIG_SYS_FSL_IFC_BANK_COUNT		8
@@ -126,8 +132,8 @@
 #define CONFIG_SYS_FSL_OCRAM_BASE		0x10000000 /* initial RAM */
 #define CONFIG_SYS_FSL_OCRAM_SIZE		0x200000 /* 2 MiB */
 #define CONFIG_SYS_FSL_DDR_BE
-#define CONFIG_SYS_LS1_DDR_BLOCK1_SIZE  ((phys_size_t)2 << 30)
-#define CONFIG_MAX_MEM_MAPPED           CONFIG_SYS_LS1_DDR_BLOCK1_SIZE
+#define CONFIG_SYS_DDR_BLOCK1_SIZE		((phys_size_t)2 << 30)
+#define CONFIG_MAX_MEM_MAPPED			CONFIG_SYS_DDR_BLOCK1_SIZE
 
 #define CONFIG_SYS_FSL_CCSR_GUR_BE
 #define CONFIG_SYS_FSL_CCSR_SCFG_BE
@@ -147,8 +153,8 @@
 #define CONFIG_SYS_FSL_PCIE_COMPAT		"fsl,qoriq-pcie-v2.4"
 
 #define CONFIG_SYS_FSL_SFP_VER_3_2
-#define CONFIG_SYS_FSL_SNVS_LE
-#define CONFIG_SYS_FSL_SEC_LE
+#define CONFIG_SYS_FSL_SEC_MON_BE
+#define CONFIG_SYS_FSL_SEC_BE
 #define CONFIG_SYS_FSL_SFP_BE
 #define CONFIG_SYS_FSL_SRK_LE
 #define CONFIG_KEY_REVOCATION

arch/arm/include/asm/arch-fsl-layerscape/cpu.h

@@ -129,7 +129,8 @@ static const struct sys_mmu_table early_mmu_table[] = {
 	{ CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FSL_IFC_BASE1,
 	  CONFIG_SYS_FSL_IFC_SIZE1, MT_DEVICE_NGNRNE, PMD_SECT_NON_SHARE },
 	{ CONFIG_SYS_FSL_DRAM_BASE1, CONFIG_SYS_FSL_DRAM_BASE1,
-	  CONFIG_SYS_FSL_DRAM_SIZE1, MT_NORMAL, PMD_SECT_OUTER_SHARE },
+	  CONFIG_SYS_FSL_DRAM_SIZE1, MT_NORMAL,
+	  PMD_SECT_OUTER_SHARE | PMD_SECT_NS },
 	/* Map IFC region #2 up to CONFIG_SYS_FLASH_BASE for NAND boot */
 	{ CONFIG_SYS_FSL_IFC_BASE2, CONFIG_SYS_FSL_IFC_BASE2,
 	  CONFIG_SYS_FLASH_BASE - CONFIG_SYS_FSL_IFC_BASE2,
@@ -138,7 +139,8 @@ static const struct sys_mmu_table early_mmu_table[] = {
 	  CONFIG_SYS_FSL_DCSR_SIZE, MT_DEVICE_NGNRNE,
 	  PMD_SECT_NON_SHARE | PMD_SECT_PXN | PMD_SECT_UXN },
 	{ CONFIG_SYS_FSL_DRAM_BASE2, CONFIG_SYS_FSL_DRAM_BASE2,
-	  CONFIG_SYS_FSL_DRAM_SIZE2, MT_NORMAL, PMD_SECT_OUTER_SHARE },
+	  CONFIG_SYS_FSL_DRAM_SIZE2, MT_NORMAL,
+	  PMD_SECT_OUTER_SHARE | PMD_SECT_NS },
 #elif defined(CONFIG_FSL_LSCH2)
 	{ CONFIG_SYS_FSL_CCSR_BASE, CONFIG_SYS_FSL_CCSR_BASE,
 	  CONFIG_SYS_FSL_CCSR_SIZE, MT_DEVICE_NGNRNE,
@@ -165,7 +167,8 @@ static const struct sys_mmu_table final_mmu_table[] = {
 	{ CONFIG_SYS_FSL_OCRAM_BASE, CONFIG_SYS_FSL_OCRAM_BASE,
 	  CONFIG_SYS_FSL_OCRAM_SIZE, MT_NORMAL, PMD_SECT_NON_SHARE },
 	{ CONFIG_SYS_FSL_DRAM_BASE1, CONFIG_SYS_FSL_DRAM_BASE1,
-	  CONFIG_SYS_FSL_DRAM_SIZE1, MT_NORMAL, PMD_SECT_OUTER_SHARE },
+	  CONFIG_SYS_FSL_DRAM_SIZE1, MT_NORMAL,
+	  PMD_SECT_OUTER_SHARE | PMD_SECT_NS },
 	{ CONFIG_SYS_FSL_QSPI_BASE2, CONFIG_SYS_FSL_QSPI_BASE2,
 	  CONFIG_SYS_FSL_QSPI_SIZE2, MT_DEVICE_NGNRNE,
 	  PMD_SECT_NON_SHARE | PMD_SECT_PXN | PMD_SECT_UXN },
@@ -183,7 +186,7 @@ static const struct sys_mmu_table final_mmu_table[] = {
 	/* For QBMAN portal, only the first 64MB is cache-enabled */
 	{ CONFIG_SYS_FSL_QBMAN_BASE, CONFIG_SYS_FSL_QBMAN_BASE,
 	  CONFIG_SYS_FSL_QBMAN_SIZE_1, MT_NORMAL,
-	  PMD_SECT_NON_SHARE | PMD_SECT_PXN | PMD_SECT_UXN },
+	  PMD_SECT_NON_SHARE | PMD_SECT_PXN | PMD_SECT_UXN | PMD_SECT_NS },
 	{ CONFIG_SYS_FSL_QBMAN_BASE + CONFIG_SYS_FSL_QBMAN_SIZE_1,
 	  CONFIG_SYS_FSL_QBMAN_BASE + CONFIG_SYS_FSL_QBMAN_SIZE_1,
 	  CONFIG_SYS_FSL_QBMAN_SIZE - CONFIG_SYS_FSL_QBMAN_SIZE_1,
@@ -212,7 +215,8 @@ static const struct sys_mmu_table final_mmu_table[] = {
 	  CONFIG_SYS_FSL_PEBUF_SIZE, MT_DEVICE_NGNRNE,
 	  PMD_SECT_NON_SHARE | PMD_SECT_PXN | PMD_SECT_UXN },
 	{ CONFIG_SYS_FSL_DRAM_BASE2, CONFIG_SYS_FSL_DRAM_BASE2,
-	  CONFIG_SYS_FSL_DRAM_SIZE2, MT_NORMAL, PMD_SECT_OUTER_SHARE },
+	  CONFIG_SYS_FSL_DRAM_SIZE2, MT_NORMAL,
+	  PMD_SECT_OUTER_SHARE | PMD_SECT_NS },
 #elif defined(CONFIG_FSL_LSCH2)
 	{ CONFIG_SYS_FSL_BOOTROM_BASE, CONFIG_SYS_FSL_BOOTROM_BASE,
 	  CONFIG_SYS_FSL_BOOTROM_SIZE, MT_DEVICE_NGNRNE,

arch/arm/include/asm/arch-fsl-layerscape/immap_lsch2.h

@@ -38,7 +38,7 @@
 #define CONFIG_SYS_PCIE3_ADDR			(CONFIG_SYS_IMMR + 0x2600000)
 #define CONFIG_SYS_FSL_SEC_ADDR			(CONFIG_SYS_IMMR + 0x700000)
 #define CONFIG_SYS_FSL_JR0_ADDR			(CONFIG_SYS_IMMR + 0x710000)
-#define CONFIG_SYS_SNVS_ADDR			(CONFIG_SYS_IMMR + 0xe90000)
+#define CONFIG_SYS_SEC_MON_ADDR			(CONFIG_SYS_IMMR + 0xe90000)
 #define CONFIG_SYS_SFP_ADDR			(CONFIG_SYS_IMMR + 0xe80200)
 
 #define CONFIG_SYS_FSL_TIMER_ADDR		0x02b00000

arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h

@@ -69,6 +69,10 @@
 #define TZASC_REGION_ATTRIBUTES_0(x)	((TZASC1_BASE + (x * 0x10000)) + 0x110)
 #define TZASC_REGION_ID_ACCESS_0(x)	((TZASC1_BASE + (x * 0x10000)) + 0x114)
 
+/* SATA */
+#define AHCI_BASE_ADDR1				(CONFIG_SYS_IMMR + 0x02200000)
+#define AHCI_BASE_ADDR2				(CONFIG_SYS_IMMR + 0x02210000)
+
 /* PCIe */
 #define CONFIG_SYS_PCIE1_ADDR			(CONFIG_SYS_IMMR + 0x2400000)
 #define CONFIG_SYS_PCIE2_ADDR			(CONFIG_SYS_IMMR + 0x2500000)

arch/arm/include/asm/arch-fsl-layerscape/soc.h

@@ -51,6 +51,37 @@ struct cpu_type {
 #define SVR_SOC_VER(svr)	(((svr) >> 8) & SVR_WO_E)
 #define IS_E_PROCESSOR(svr)	(!((svr >> 8) & 0x1))
 
+/* ahci port register default value */
+#define AHCI_PORT_PHY_1_CFG    0xa003fffe
+#define AHCI_PORT_PHY_2_CFG    0x28184d1f
+#define AHCI_PORT_PHY_3_CFG    0x0e081509
+#define AHCI_PORT_TRANS_CFG    0x08000029
+
+/* AHCI (sata) register map */
+struct ccsr_ahci {
+	u32 res1[0xa4/4];	/* 0x0 - 0xa4 */
+	u32 pcfg;	/* port config */
+	u32 ppcfg;	/* port phy1 config */
+	u32 pp2c;	/* port phy2 config */
+	u32 pp3c;	/* port phy3 config */
+	u32 pp4c;	/* port phy4 config */
+	u32 pp5c;	/* port phy5 config */
+	u32 axicc;	/* AXI cache control */
+	u32 paxic;	/* port AXI config */
+	u32 axipc;	/* AXI PROT control */
+	u32 ptc;	/* port Trans Config */
+	u32 pts;	/* port Trans Status */
+	u32 plc;	/* port link config */
+	u32 plc1;	/* port link config1 */
+	u32 plc2;	/* port link config2 */
+	u32 pls;	/* port link status */
+	u32 pls1;	/* port link status1 */
+	u32 pcmdc;	/* port CMD config */
+	u32 ppcs;	/* port phy control status */
+	u32 pberr;	/* port 0/1 BIST error */
+	u32 cmds;	/* port 0/1 CMD status error */
+};
+
 #ifdef CONFIG_FSL_LSCH3
 void fsl_lsch3_early_init_f(void);
 #elif defined(CONFIG_FSL_LSCH2)

arch/arm/include/asm/arch-ls102xa/immap_ls102xa.h

@@ -11,6 +11,8 @@
 #define SVR_MIN(svr)		(((svr) >>  0) & 0xf)
 #define SVR_SOC_VER(svr)	(((svr) >> 8) & 0x7ff)
 #define IS_E_PROCESSOR(svr)	(svr & 0x80000)
+#define IS_SVR_REV(svr, maj, min) \
+		((SVR_MAJ(svr) == maj) && (SVR_MIN(svr) == min))
 
 #define SOC_VER_SLS1020		0x00
 #define SOC_VER_LS1020		0x10
@@ -150,6 +152,12 @@ struct ccsr_gur {
 #define SCFG_ETSECCMCR_GE1_CLK125	0x08000000
 #define SCFG_PIXCLKCR_PXCKEN		0x80000000
 #define SCFG_QSPI_CLKSEL		0xc0100000
+#define SCFG_SNPCNFGCR_SEC_RD_WR	0xc0000000
+#define SCFG_SNPCNFGCR_DCU_RD_WR	0x03000000
+#define SCFG_SNPCNFGCR_SATA_RD_WR	0x00c00000
+#define SCFG_SNPCNFGCR_USB3_RD_WR	0x00300000
+#define SCFG_SNPCNFGCR_DBG_RD_WR	0x000c0000
+#define SCFG_SNPCNFGCR_EDMA_SNP		0x00020000
 #define SCFG_ENDIANCR_LE		0x80000000
 
 /* Supplemental Configuration Unit */
@@ -222,7 +230,7 @@ struct ccsr_scfg {
 	u32 scfgrevcr;
 	u32 coresrencr;
 	u32 pex2pmrdsr;
-	u32 ddrc1cr;
+	u32 eddrtqcfg;
 	u32 ddrc2cr;
 	u32 ddrc3cr;
 	u32 ddrc4cr;
@@ -422,4 +430,7 @@ struct ccsr_ahci {
 	u32 pberr;	/* port 0/1 BIST error */
 	u32 cmds;	/* port 0/1 CMD status error */
 };
+
+uint get_svr(void);
+
 #endif	/* __ASM_ARCH_LS102XA_IMMAP_H_ */

arch/arm/include/asm/arch-ls102xa/ls102xa_soc.h

@@ -0,0 +1,12 @@
+/*
+ * Copyright 2015 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __FSL_LS102XA_SOC_H
+#define __FSL_LS102XA_SOC_H
+
+unsigned int get_soc_major_rev(void);
+int arch_soc_init(void);
+#endif /* __FSL_LS102XA_SOC_H */

arch/arm/include/asm/fsl_secure_boot.h

@@ -11,13 +11,17 @@
 #define CONFIG_CMD_ESBC_VALIDATE
 #define CONFIG_FSL_SEC_MON
 #define CONFIG_SHA_PROG_HW_ACCEL
-#define CONFIG_DM
 #define CONFIG_RSA
 #define CONFIG_RSA_FREESCALE_EXP
+
 #ifndef CONFIG_FSL_CAAM
 #define CONFIG_FSL_CAAM
 #endif
 
+#ifndef CONFIG_DM
+#define CONFIG_DM
+#endif
+
 #define CONFIG_KEY_REVOCATION
 #ifndef CONFIG_SYS_RAMBOOT
 /* The key used for verification of next level images

arch/powerpc/cpu/mpc85xx/cmd_errata.c

@@ -7,7 +7,7 @@
 #include <common.h>
 #include <command.h>
 #include <linux/compiler.h>
-#include <asm/fsl_errata.h>
+#include <fsl_errata.h>
 #include <asm/processor.h>
 #include <fsl_usb.h>
 #include "fsl_corenet_serdes.h"

arch/powerpc/cpu/mpc85xx/cpu_init.c

@@ -19,7 +19,7 @@
 #include <asm/io.h>
 #include <asm/cache.h>
 #include <asm/mmu.h>
-#include <asm/fsl_errata.h>
+#include <fsl_errata.h>
 #include <asm/fsl_law.h>
 #include <asm/fsl_serdes.h>
 #include <asm/fsl_srio.h>

arch/powerpc/cpu/mpc85xx/fsl_corenet2_serdes.c

@@ -11,7 +11,7 @@
 #include <asm/processor.h>
 #include <asm/fsl_law.h>
 #include <asm/errno.h>
-#include <asm/fsl_errata.h>
+#include <fsl_errata.h>
 #include "fsl_corenet2_serdes.h"
 
 #ifdef CONFIG_SYS_FSL_SRDS_1
@@ -184,7 +184,7 @@ void serdes_init(u32 sd, u32 sd_addr, u32 sd_prctl_mask, u32 sd_prctl_shift,
 	u32 cfg;
 	int lane;
 
-	memset(serdes_prtcl_map, 0, sizeof(serdes_prtcl_map));
+	memset(serdes_prtcl_map, 0, sizeof(u8) * SERDES_PRCTL_COUNT);
 #ifdef CONFIG_SYS_FSL_ERRATUM_A007186
 	struct ccsr_sfp_regs  __iomem *sfp_regs =
 			(struct ccsr_sfp_regs __iomem *)(CONFIG_SYS_SFP_ADDR);

arch/powerpc/include/asm/config_mpc85xx.h

@@ -807,6 +807,7 @@ defined(CONFIG_PPC_T1020) || defined(CONFIG_PPC_T1022)
 #define MAX_QE_RISC			1
 #define QE_NUM_OF_SNUM			28
 #define CONFIG_SYS_FSL_SFP_VER_3_0
+#define CONFIG_SYS_FSL_ERRATUM_A008378
 
 #elif defined(CONFIG_PPC_T1024) || defined(CONFIG_PPC_T1023) ||\
 defined(CONFIG_PPC_T1014) || defined(CONFIG_PPC_T1013)
@@ -854,6 +855,7 @@ defined(CONFIG_PPC_T1014) || defined(CONFIG_PPC_T1013)
 #define MAX_QE_RISC			1
 #define QE_NUM_OF_SNUM			28
 #define CONFIG_SYS_FSL_SFP_VER_3_0
+#define CONFIG_SYS_FSL_ERRATUM_A008378
 
 #elif defined(CONFIG_PPC_T2080) || defined(CONFIG_PPC_T2081)
 #define CONFIG_E6500

board/freescale/common/fman.c

@@ -52,6 +52,8 @@ int fdt_set_phy_handle(void *fdt, char *compat, phys_addr_t addr,
 	if (!ph)
 		return -FDT_ERR_BADPHANDLE;
 
+	ph = cpu_to_fdt32(ph);
+
 	offset = fdt_node_offset_by_compat_reg(fdt, compat, addr);
 	if (offset < 0)
 		return offset;

board/freescale/common/fsl_validate.c

@@ -15,7 +15,7 @@
 #include <u-boot/rsa-mod-exp.h>
 #include <hash.h>
 #include <fsl_secboot_err.h>
-#ifndef CONFIG_MPC85xx
+#ifdef CONFIG_LS102XA
 #include <asm/arch/immap_ls102xa.h>
 #endif
 
@@ -99,7 +99,8 @@ int get_csf_base_addr(u32 *csf_addr, u32 *flash_base_addr)
 	struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
 	u32 csf_hdr_addr = in_be32(&gur->scratchrw[0]);
 
-	if (memcmp((u8 *)csf_hdr_addr, barker_code, ESBC_BARKER_LEN))
+	if (memcmp((u8 *)(uintptr_t)csf_hdr_addr,
+		   barker_code, ESBC_BARKER_LEN))
 		return -1;
 
 	*csf_addr = csf_hdr_addr;
@@ -117,7 +118,7 @@ static int get_ie_info_addr(u32 *ie_addr)
 	if (get_csf_base_addr(&csf_addr, &flash_base_addr))
 		return -1;
 
-	hdr = (struct fsl_secboot_img_hdr *)csf_addr;
+	hdr = (struct fsl_secboot_img_hdr *)(uintptr_t)csf_addr;
 
 	/* For SoC's with Trust Architecture v1 with corenet bus
 	 * the sg table field in CSF header has absolute address
@@ -130,7 +131,7 @@ static int get_ie_info_addr(u32 *ie_addr)
 		 (((u32)hdr->psgtable & ~(CONFIG_SYS_PBI_FLASH_BASE)) +
 		  flash_base_addr);
 #else
-	sg_tbl = (struct fsl_secboot_sg_table *)(csf_addr +
+	sg_tbl = (struct fsl_secboot_sg_table *)(uintptr_t)(csf_addr +
 						 (u32)hdr->psgtable);
 #endif
 
@@ -379,8 +380,8 @@ static int calc_img_key_hash(struct fsl_secboot_img_priv *img)
 #ifdef CONFIG_KEY_REVOCATION
 	if (check_srk(img)) {
 		ret = algo->hash_update(algo, ctx,
-			(u8 *)(img->ehdrloc + img->hdr.srk_tbl_off),
-			img->hdr.len_kr.num_srk * sizeof(struct srk_table), 1);
+		      (u8 *)(uintptr_t)(img->ehdrloc + img->hdr.srk_tbl_off),
+		      img->hdr.len_kr.num_srk * sizeof(struct srk_table), 1);
 		srk = 1;
 	}
 #endif
@@ -438,8 +439,8 @@ static int calc_esbchdr_esbc_hash(struct fsl_secboot_img_priv *img)
 #ifdef CONFIG_KEY_REVOCATION
 	if (check_srk(img)) {
 		ret = algo->hash_update(algo, ctx,
-			(u8 *)(img->ehdrloc + img->hdr.srk_tbl_off),
-			img->hdr.len_kr.num_srk * sizeof(struct srk_table), 0);
+		      (u8 *)(uintptr_t)(img->ehdrloc + img->hdr.srk_tbl_off),
+		      img->hdr.len_kr.num_srk * sizeof(struct srk_table), 0);
 		key_hash = 1;
 	}
 #endif
@@ -454,8 +455,13 @@ static int calc_esbchdr_esbc_hash(struct fsl_secboot_img_priv *img)
 		return ret;
 
 	/* Update hash for actual Image */
+#ifdef CONFIG_ESBC_ADDR_64BIT
 	ret = algo->hash_update(algo, ctx,
-			(u8 *)img->hdr.pimg, img->hdr.img_size, 1);
+		(u8 *)(uintptr_t)img->hdr.pimg64, img->hdr.img_size, 1);
+#else
+	ret = algo->hash_update(algo, ctx,
+		(u8 *)(uintptr_t)img->hdr.pimg, img->hdr.img_size, 1);
+#endif
 	if (ret)
 		return ret;
 
@@ -533,7 +539,7 @@ static int read_validate_esbc_client_header(struct fsl_secboot_img_priv *img)
 {
 	char buf[20];
 	struct fsl_secboot_img_hdr *hdr = &img->hdr;
-	void *esbc = (u8 *)img->ehdrloc;
+	void *esbc = (u8 *)(uintptr_t)img->ehdrloc;
 	u8 *k, *s;
 #ifdef CONFIG_KEY_REVOCATION
 	u32 ret;
@@ -549,7 +555,11 @@ static int read_validate_esbc_client_header(struct fsl_secboot_img_priv *img)
 	if (memcmp(hdr->barker, barker_code, ESBC_BARKER_LEN))
 		return ERROR_ESBC_CLIENT_HEADER_BARKER;
 
+#ifdef CONFIG_ESBC_ADDR_64BIT
+	sprintf(buf, "%llx", hdr->pimg64);
+#else
 	sprintf(buf, "%x", hdr->pimg);
+#endif
 	setenv("img_addr", buf);
 
 	if (!hdr->img_size)
@@ -594,7 +604,7 @@ static int read_validate_esbc_client_header(struct fsl_secboot_img_priv *img)
 	if (!key_found && check_ie(img)) {
 		if (get_ie_info_addr(&img->ie_addr))
 			return ERROR_IE_TABLE_NOT_FOUND;
-		ie_info = (struct ie_key_info *)img->ie_addr;
+		ie_info = (struct ie_key_info *)(uintptr_t)img->ie_addr;
 		if (ie_info->num_keys == 0 || ie_info->num_keys > 32)
 			return ERROR_ESBC_CLIENT_HEADER_INVALID_IE_NUM_ENTRY;
 
@@ -748,7 +758,7 @@ int fsl_secboot_validate(cmd_tbl_t *cmdtp, int flag, int argc,
 
 	hdr = &img->hdr;
 	img->ehdrloc = addr;
-	esbc = (u8 *)img->ehdrloc;
+	esbc = (u8 *)(uintptr_t)img->ehdrloc;
 
 	memcpy(hdr, esbc, sizeof(struct fsl_secboot_img_hdr));
 

board/freescale/ls1021aqds/ls1021aqds.c

@@ -11,6 +11,7 @@
 #include <asm/arch/clock.h>
 #include <asm/arch/fsl_serdes.h>
 #include <asm/arch/ls102xa_stream_id.h>
+#include <asm/arch/ls102xa_soc.h>
 #include <asm/arch/ls102xa_devdis.h>
 #include <asm/arch/ls102xa_sata.h>
 #include <hwconfig.h>
@@ -140,17 +141,6 @@ unsigned long get_board_ddr_clk(void)
 	return 66666666;
 }
 
-unsigned int get_soc_major_rev(void)
-{
-	struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
-	unsigned int svr, major;
-
-	svr = in_be32(&gur->svr);
-	major = SVR_MAJ(svr);
-
-	return major;
-}
-
 int select_i2c_ch_pca9547(u8 ch)
 {
 	int ret;
@@ -193,8 +183,6 @@ int board_mmc_init(bd_t *bis)
 int board_early_init_f(void)
 {
 	struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
-	struct ccsr_cci400 *cci = (struct ccsr_cci400 *)CONFIG_SYS_CCI400_ADDR;
-	unsigned int major;
 
 #ifdef CONFIG_TSEC_ENET
 	/* clear BD & FR bits for BE BD's and frame data */
@@ -205,40 +193,7 @@ int board_early_init_f(void)
 	init_early_memctl_regs();
 #endif
 
-#ifdef CONFIG_FSL_QSPI
-	out_be32(&scfg->qspi_cfg, SCFG_QSPI_CLKSEL);
-#endif
-
-#ifdef CONFIG_FSL_DCU_FB
-	out_be32(&scfg->pixclkcr, SCFG_PIXCLKCR_PXCKEN);
-#endif
-
-	/* Configure Little endian for SAI, ASRC and SPDIF */
-	out_be32(&scfg->endiancr, SCFG_ENDIANCR_LE);
-
-	/*
-	 * Enable snoop requests and DVM message requests for
-	 * Slave insterface S4 (A7 core cluster)
-	 */
-	out_le32(&cci->slave[4].snoop_ctrl,
-		 CCI400_DVM_MESSAGE_REQ_EN | CCI400_SNOOP_REQ_EN);
-
-	major = get_soc_major_rev();
-	if (major == SOC_MAJOR_VER_1_0) {
-		/*
-		 * Set CCI-400 Slave interface S1, S2 Shareable Override
-		 * Register All transactions are treated as non-shareable
-		 */
-		out_le32(&cci->slave[1].sha_ord, CCI400_SHAORD_NON_SHAREABLE);
-		out_le32(&cci->slave[2].sha_ord, CCI400_SHAORD_NON_SHAREABLE);
-
-		/* Workaround for the issue that DDR could not respond to
-		 * barrier transaction which is generated by executing DSB/ISB
-		 * instruction. Set CCI-400 control override register to
-		 * terminate the barrier transaction. After DDR is initialized,
-		 * allow barrier transaction to DDR again */
-		out_le32(&cci->ctrl_ord, CCI400_CTRLORD_TERM_BARRIER);
-	}
+	arch_soc_init();
 
 #if defined(CONFIG_DEEP_SLEEP)
 	if (is_warm_boot())

board/freescale/ls1021atwr/ls1021atwr.c

@@ -12,6 +12,7 @@
 #include <asm/arch/fsl_serdes.h>
 #include <asm/arch/ls102xa_stream_id.h>
 #include <asm/arch/ls102xa_devdis.h>
+#include <asm/arch/ls102xa_soc.h>
 #include <asm/arch/ls102xa_sata.h>
 #include <hwconfig.h>
 #include <mmc.h>
@@ -138,17 +139,6 @@ int checkboard(void)
 	return 0;
 }
 
-unsigned int get_soc_major_rev(void)
-{
-	struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
-	unsigned int svr, major;
-
-	svr = in_be32(&gur->svr);
-	major = SVR_MAJ(svr);
-
-	return major;
-}
-
 void ddrmc_init(void)
 {
 	struct ccsr_ddr *ddr = (struct ccsr_ddr *)CONFIG_SYS_FSL_DDR_ADDR;
@@ -394,8 +384,6 @@ conflict:
 int board_early_init_f(void)
 {
 	struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
-	struct ccsr_cci400 *cci = (struct ccsr_cci400 *)CONFIG_SYS_CCI400_ADDR;
-	unsigned int major;
 
 #ifdef CONFIG_TSEC_ENET
 	/* clear BD & FR bits for BE BD's and frame data */
@@ -407,33 +395,7 @@ int board_early_init_f(void)
 	init_early_memctl_regs();
 #endif
 
-#ifdef CONFIG_FSL_DCU_FB
-	out_be32(&scfg->pixclkcr, SCFG_PIXCLKCR_PXCKEN);
-#endif
-
-#ifdef CONFIG_FSL_QSPI
-	out_be32(&scfg->qspi_cfg, SCFG_QSPI_CLKSEL);
-#endif
-
-	/* Configure Little endian for SAI, ASRC and SPDIF */
-	out_be32(&scfg->endiancr, SCFG_ENDIANCR_LE);
-
-	/*
-	 * Enable snoop requests and DVM message requests for
-	 * Slave insterface S4 (A7 core cluster)
-	 */
-	out_le32(&cci->slave[4].snoop_ctrl,
-		 CCI400_DVM_MESSAGE_REQ_EN | CCI400_SNOOP_REQ_EN);
-
-	major = get_soc_major_rev();
-	if (major == SOC_MAJOR_VER_1_0) {
-		/*
-		 * Set CCI-400 Slave interface S1, S2 Shareable Override
-		 * Register All transactions are treated as non-shareable
-		 */
-		out_le32(&cci->slave[1].sha_ord, CCI400_SHAORD_NON_SHAREABLE);
-		out_le32(&cci->slave[2].sha_ord, CCI400_SHAORD_NON_SHAREABLE);
-	}
+	arch_soc_init();
 
 #if defined(CONFIG_DEEP_SLEEP)
 	if (is_warm_boot()) {

board/freescale/ls1043aqds/ddr.c

@@ -126,6 +126,15 @@ phys_size_t initdram(int board_type)
 
 void dram_init_banksize(void)
 {
+	/*
+	 * gd->secure_ram tracks the location of secure memory.
+	 * It was set as if the memory starts from 0.
+	 * The address needs to add the offset of its bank.
+	 */
 	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
 	gd->bd->bi_dram[0].size = gd->ram_size;
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+	gd->secure_ram = gd->bd->bi_dram[0].start + gd->secure_ram;
+	gd->secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
+#endif
 }

board/freescale/ls1043ardb/MAINTAINERS

@@ -7,3 +7,8 @@ F:	include/configs/ls1043ardb.h
 F:	configs/ls1043ardb_defconfig
 F:	configs/ls1043ardb_nand_defconfig
 F:	configs/ls1043ardb_sdcard_defconfig
+
+LS1043A_SECURE_BOOT BOARD
+M:	Aneesh Bansal <aneesh.bansal@freescale.com>
+S:	Maintained
+F:	configs/ls1043ardb_SECURE_BOOT_defconfig

board/freescale/ls1043ardb/ddr.c

@@ -186,6 +186,28 @@ phys_size_t initdram(int board_type)
 
 void dram_init_banksize(void)
 {
+	/*
+	 * gd->secure_ram tracks the location of secure memory.
+	 * It was set as if the memory starts from 0.
+	 * The address needs to add the offset of its bank.
+	 */
 	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
-	gd->bd->bi_dram[0].size = gd->ram_size;
+	if (gd->ram_size > CONFIG_SYS_DDR_BLOCK1_SIZE) {
+		gd->bd->bi_dram[0].size = CONFIG_SYS_DDR_BLOCK1_SIZE;
+		gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
+		gd->bd->bi_dram[1].size = gd->ram_size -
+					  CONFIG_SYS_DDR_BLOCK1_SIZE;
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+		gd->secure_ram = gd->bd->bi_dram[1].start +
+				 gd->secure_ram -
+				 CONFIG_SYS_DDR_BLOCK1_SIZE;
+		gd->secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
+#endif
+	} else {
+		gd->bd->bi_dram[0].size = gd->ram_size;
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+		gd->secure_ram = gd->bd->bi_dram[0].start + gd->secure_ram;
+		gd->secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
+#endif
+	}
 }

board/freescale/ls1043ardb/ls1043ardb.c

@@ -18,6 +18,8 @@
 #include <fsl_csu.h>
 #include <fsl_esdhc.h>
 #include <fsl_ifc.h>
+#include <environment.h>
+#include <fsl_sec.h>
 #include "cpld.h"
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -123,13 +125,37 @@ int config_board_mux(void)
 int misc_init_r(void)
 {
 	config_board_mux();
-
+#ifdef CONFIG_SECURE_BOOT
+	/* In case of Secure Boot, the IBR configures the SMMU
+	 * to allow only Secure transactions.
+	 * SMMU must be reset in bypass mode.
+	 * Set the ClientPD bit and Clear the USFCFG Bit
+	 */
+	u32 val;
+	val = (in_le32(SMMU_SCR0) | SCR0_CLIENTPD_MASK) & ~(SCR0_USFCFG_MASK);
+	out_le32(SMMU_SCR0, val);
+	val = (in_le32(SMMU_NSCR0) | SCR0_CLIENTPD_MASK) & ~(SCR0_USFCFG_MASK);
+	out_le32(SMMU_NSCR0, val);
+#endif
+#ifdef CONFIG_FSL_CAAM
+	return sec_init();
+#endif
 	return 0;
 }
 #endif
 
 int ft_board_setup(void *blob, bd_t *bd)
 {
+	u64 base[CONFIG_NR_DRAM_BANKS];
+	u64 size[CONFIG_NR_DRAM_BANKS];
+
+	/* fixup DT for the two DDR banks */
+	base[0] = gd->bd->bi_dram[0].start;
+	size[0] = gd->bd->bi_dram[0].size;
+	base[1] = gd->bd->bi_dram[1].start;
+	size[1] = gd->bd->bi_dram[1].size;
+
+	fdt_fixup_memory_banks(blob, base, size, 2);
 	ft_cpu_setup(blob, bd);
 
 #ifdef CONFIG_SYS_DPAA_FMAN

board/freescale/ls2080a/ddr.c

@@ -175,14 +175,29 @@ void dram_init_banksize(void)
 	phys_size_t dp_ddr_size;
 #endif
 
+	/*
+	 * gd->secure_ram tracks the location of secure memory.
+	 * It was set as if the memory starts from 0.
+	 * The address needs to add the offset of its bank.
+	 */
 	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
 	if (gd->ram_size > CONFIG_SYS_LS2_DDR_BLOCK1_SIZE) {
 		gd->bd->bi_dram[0].size = CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
 		gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
 		gd->bd->bi_dram[1].size = gd->ram_size -
 					  CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+		gd->secure_ram = gd->bd->bi_dram[1].start +
+				 gd->secure_ram -
+				 CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
+		gd->secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
+#endif
 	} else {
 		gd->bd->bi_dram[0].size = gd->ram_size;
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+		gd->secure_ram = gd->bd->bi_dram[0].start + gd->secure_ram;
+		gd->secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
+#endif
 	}
 
 #ifdef CONFIG_SYS_DP_DDR_BASE_PHY

board/freescale/ls2080a/ls2080a.c

@@ -68,23 +68,6 @@ int arch_misc_init(void)
 }
 #endif
 
-unsigned long get_dram_size_to_hide(void)
-{
-	unsigned long dram_to_hide = 0;
-
-/* Carve the Debug Server private DRAM block from the end of DRAM */
-#ifdef CONFIG_FSL_DEBUG_SERVER
-	dram_to_hide += debug_server_get_dram_block_size();
-#endif
-
-/* Carve the MC private DRAM block from the end of DRAM */
-#ifdef CONFIG_FSL_MC_ENET
-	dram_to_hide += mc_get_dram_block_size();
-#endif
-
-	return roundup(dram_to_hide, CONFIG_SYS_MEM_TOP_HIDE_MIN);
-}
-
 int board_eth_init(bd_t *bis)
 {
 	int error = 0;

board/freescale/ls2080aqds/ddr.c

@@ -134,10 +134,18 @@ found:
 	popts->zq_en = 1;
 
 	if (ddr_freq < 2350) {
-		popts->ddr_cdr1 = DDR_CDR1_DHC_EN |
-				  DDR_CDR1_ODT(DDR_CDR_ODT_60ohm);
-		popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_60ohm) |
-				  DDR_CDR2_VREF_RANGE_2;
+		if (pdimm[0].n_ranks == 2 && pdimm[1].n_ranks == 2) {
+			/* four chip-selects */
+			popts->ddr_cdr1 = DDR_CDR1_DHC_EN |
+					  DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
+			popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm);
+			popts->twot_en = 1; /* enable 2T timing */
+		} else {
+			popts->ddr_cdr1 = DDR_CDR1_DHC_EN |
+					  DDR_CDR1_ODT(DDR_CDR_ODT_60ohm);
+			popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_60ohm) |
+					  DDR_CDR2_VREF_RANGE_2;
+		}
 	} else {
 		popts->ddr_cdr1 = DDR_CDR1_DHC_EN |
 				  DDR_CDR1_ODT(DDR_CDR_ODT_100ohm);
@@ -167,14 +175,29 @@ void dram_init_banksize(void)
 	phys_size_t dp_ddr_size;
 #endif
 
+	/*
+	 * gd->secure_ram tracks the location of secure memory.
+	 * It was set as if the memory starts from 0.
+	 * The address needs to add the offset of its bank.
+	 */
 	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
 	if (gd->ram_size > CONFIG_SYS_LS2_DDR_BLOCK1_SIZE) {
 		gd->bd->bi_dram[0].size = CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
 		gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
 		gd->bd->bi_dram[1].size = gd->ram_size -
 					  CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+		gd->secure_ram = gd->bd->bi_dram[1].start +
+				 gd->secure_ram -
+				 CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
+		gd->secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
+#endif
 	} else {
 		gd->bd->bi_dram[0].size = gd->ram_size;
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+		gd->secure_ram = gd->bd->bi_dram[0].start + gd->secure_ram;
+		gd->secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
+#endif
 	}
 
 #ifdef CONFIG_SYS_DP_DDR_BASE_PHY

board/freescale/ls2080aqds/ls2080aqds.c

@@ -253,23 +253,6 @@ int arch_misc_init(void)
 }
 #endif
 
-unsigned long get_dram_size_to_hide(void)
-{
-	unsigned long dram_to_hide = 0;
-
-/* Carve the Debug Server private DRAM block from the end of DRAM */
-#ifdef CONFIG_FSL_DEBUG_SERVER
-	dram_to_hide += debug_server_get_dram_block_size();
-#endif
-
-/* Carve the MC private DRAM block from the end of DRAM */
-#ifdef CONFIG_FSL_MC_ENET
-	dram_to_hide += mc_get_dram_block_size();
-#endif
-
-	return roundup(dram_to_hide, CONFIG_SYS_MEM_TOP_HIDE_MIN);
-}
-
 #ifdef CONFIG_FSL_MC_ENET
 void fdt_fixup_board_enet(void *fdt)
 {

board/freescale/ls2080ardb/ddr.c

@@ -134,10 +134,18 @@ found:
 	popts->zq_en = 1;
 
 	if (ddr_freq < 2350) {
-		popts->ddr_cdr1 = DDR_CDR1_DHC_EN |
-				  DDR_CDR1_ODT(DDR_CDR_ODT_60ohm);
-		popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_60ohm) |
-				  DDR_CDR2_VREF_RANGE_2;
+		if (pdimm[0].n_ranks == 2 && pdimm[1].n_ranks == 2) {
+			/* four chip-selects */
+			popts->ddr_cdr1 = DDR_CDR1_DHC_EN |
+					  DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
+			popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm);
+			popts->twot_en = 1;	/* enable 2T timing */
+		} else {
+			popts->ddr_cdr1 = DDR_CDR1_DHC_EN |
+					  DDR_CDR1_ODT(DDR_CDR_ODT_60ohm);
+			popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_60ohm) |
+					  DDR_CDR2_VREF_RANGE_2;
+		}
 	} else {
 		popts->ddr_cdr1 = DDR_CDR1_DHC_EN |
 				  DDR_CDR1_ODT(DDR_CDR_ODT_100ohm);
@@ -167,14 +175,29 @@ void dram_init_banksize(void)
 	phys_size_t dp_ddr_size;
 #endif
 
+	/*
+	 * gd->secure_ram tracks the location of secure memory.
+	 * It was set as if the memory starts from 0.
+	 * The address needs to add the offset of its bank.
+	 */
 	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
 	if (gd->ram_size > CONFIG_SYS_LS2_DDR_BLOCK1_SIZE) {
 		gd->bd->bi_dram[0].size = CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
 		gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
 		gd->bd->bi_dram[1].size = gd->ram_size -
 					  CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+		gd->secure_ram = gd->bd->bi_dram[1].start +
+				 gd->secure_ram -
+				 CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
+		gd->secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
+#endif
 	} else {
 		gd->bd->bi_dram[0].size = gd->ram_size;
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+		gd->secure_ram = gd->bd->bi_dram[0].start + gd->secure_ram;
+		gd->secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
+#endif
 	}
 
 #ifdef CONFIG_SYS_DP_DDR_BASE_PHY

board/freescale/ls2080ardb/ls2080ardb.c

@@ -219,23 +219,6 @@ int arch_misc_init(void)
 }
 #endif
 
-unsigned long get_dram_size_to_hide(void)
-{
-	unsigned long dram_to_hide = 0;
-
-/* Carve the Debug Server private DRAM block from the end of DRAM */
-#ifdef CONFIG_FSL_DEBUG_SERVER
-	dram_to_hide += debug_server_get_dram_block_size();
-#endif
-
-/* Carve the MC private DRAM block from the end of DRAM */
-#ifdef CONFIG_FSL_MC_ENET
-	dram_to_hide += mc_get_dram_block_size();
-#endif
-
-	return roundup(dram_to_hide, CONFIG_SYS_MEM_TOP_HIDE_MIN);
-}
-
 #ifdef CONFIG_FSL_MC_ENET
 void fdt_fixup_board_enet(void *fdt)
 {

common/board_f.c

@@ -317,6 +317,15 @@ __weak ulong board_get_usable_ram_top(ulong total_size)
 	return gd->ram_top;
 }
 
+__weak phys_size_t board_reserve_ram_top(phys_size_t ram_size)
+{
+#ifdef CONFIG_SYS_MEM_TOP_HIDE
+	return ram_size - CONFIG_SYS_MEM_TOP_HIDE;
+#else
+	return ram_size;
+#endif
+}
+
 static int setup_dest_addr(void)
 {
 	debug("Monitor len: %08lX\n", gd->mon_len);
@@ -324,19 +333,26 @@ static int setup_dest_addr(void)
 	 * Ram is setup, size stored in gd !!
 	 */
 	debug("Ram size: %08lX\n", (ulong)gd->ram_size);
-#if defined(CONFIG_SYS_MEM_TOP_HIDE)
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+	/* Reserve memory for secure MMU tables, and/or security monitor */
+	gd->ram_size -= CONFIG_SYS_MEM_RESERVE_SECURE;
+	/*
+	 * Record secure memory location. Need recalcuate if memory splits
+	 * into banks, or the ram base is not zero.
+	 */
+	gd->secure_ram = gd->ram_size;
+#endif
 	/*
 	 * Subtract specified amount of memory to hide so that it won't
 	 * get "touched" at all by U-Boot. By fixing up gd->ram_size
 	 * the Linux kernel should now get passed the now "corrected"
-	 * memory size and won't touch it either. This should work
-	 * for arch/ppc and arch/powerpc. Only Linux board ports in
-	 * arch/powerpc with bootwrapper support, that recalculate the
-	 * memory size from the SDRAM controller setup will have to
-	 * get fixed.
+	 * memory size and won't touch it either. This has been used
+	 * by arch/powerpc exclusively. Now ARMv8 takes advantage of
+	 * thie mechanism. If memory is split into banks, addresses
+	 * need to be calculated.
 	 */
-	gd->ram_size -= CONFIG_SYS_MEM_TOP_HIDE;
-#endif
+	gd->ram_size = board_reserve_ram_top(gd->ram_size);
+
 #ifdef CONFIG_SYS_SDRAM_BASE
 	gd->ram_top = CONFIG_SYS_SDRAM_BASE;
 #endif

common/cmd_bdinfo.c

@@ -382,6 +382,12 @@ static int do_bdinfo(cmd_tbl_t *cmdtp, int flag, int argc,
 		print_num("-> size",	bd->bi_dram[i].size);
 	}
 
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+	if (gd->secure_ram & MEM_RESERVE_SECURE_SECURED) {
+		print_num("Secure ram",
+			  gd->secure_ram & MEM_RESERVE_SECURE_ADDR_MASK);
+	}
+#endif
 #if defined(CONFIG_CMD_NET) && !defined(CONFIG_DM_ETH)
 	print_eths();
 #endif

common/cmd_blob.c

@@ -73,9 +73,9 @@ static int do_blob(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[])
 	len = simple_strtoul(argv[4], NULL, 16);
 	key_addr = simple_strtoul(argv[5], NULL, 16);
 
-	km_ptr = (uint8_t *)key_addr;
-	src_ptr = (uint8_t *)src_addr;
-	dst_ptr = (uint8_t *)dst_addr;
+	km_ptr = (uint8_t *)(uintptr_t)key_addr;
+	src_ptr = (uint8_t *)(uintptr_t)src_addr;
+	dst_ptr = (uint8_t *)(uintptr_t)dst_addr;
 
 	if (enc)
 		ret = blob_encap(km_ptr, src_ptr, dst_ptr, len);

configs/ls1043ardb_SECURE_BOOT_defconfig

@@ -0,0 +1,9 @@
+CONFIG_ARM=y
+CONFIG_TARGET_LS1043ARDB=y
+CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4, SECURE_BOOT"
+CONFIG_SYS_NS16550=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-rdb"
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_SPI_FLASH=y
+CONFIG_DM_SPI=y

drivers/crypto/fsl/jr.c

@@ -470,17 +470,13 @@ static void kick_trng(int ent_delay)
 	sec_out32(&rng->rtfreqmin, ent_delay >> 2);
 	/* disable maximum frequency count */
 	sec_out32(&rng->rtfreqmax, RTFRQMAX_DISABLE);
-	/* read the control register */
-	val = sec_in32(&rng->rtmctl);
 	/*
 	 * select raw sampling in both entropy shifter
 	 * and statistical checker
 	 */
-	sec_setbits32(&val, RTMCTL_SAMP_MODE_RAW_ES_SC);
+	sec_setbits32(&rng->rtmctl, RTMCTL_SAMP_MODE_RAW_ES_SC);
 	/* put RNG4 into run mode */
-	sec_clrbits32(&val, RTMCTL_PRGM);
-	/* write back the control register */
-	sec_out32(&rng->rtmctl, val);
+	sec_clrbits32(&rng->rtmctl, RTMCTL_PRGM);
 }
 
 static int rng_init(void)

drivers/ddr/fsl/ctrl_regs.c

@@ -317,7 +317,24 @@ static void set_timing_cfg_0(const unsigned int ctrl_num,
 
 	/* for faster clock, need more time for data setup */
 	trwt_mclk = (data_rate/1000000 > 1900) ? 3 : 2;
-	twrt_mclk = 1;
+
+	/*
+	 * for single quad-rank DIMM and two-slot DIMMs
+	 * to avoid ODT overlap
+	 */
+	switch (avoid_odt_overlap(dimm_params)) {
+	case 2:
+		twrt_mclk = 2;
+		twwt_mclk = 2;
+		trrt_mclk = 2;
+		break;
+	default:
+		twrt_mclk = 1;
+		twwt_mclk = 1;
+		trrt_mclk = 0;
+		break;
+	}
+
 	act_pd_exit_mclk = picos_to_mclk(ctrl_num, txp);
 	pre_pd_exit_mclk = act_pd_exit_mclk;
 	/*
@@ -1117,10 +1134,18 @@ static void set_ddr_sdram_mode_9(fsl_ddr_cfg_regs_t *ddr,
 	unsigned short esdmode4 = 0;	/* Extended SDRAM mode 4 */
 	unsigned short esdmode5;	/* Extended SDRAM mode 5 */
 	int rtt_park = 0;
-
+	bool four_cs = false;
+
+#if CONFIG_CHIP_SELECTS_PER_CTRL == 4
+	if ((ddr->cs[0].config & SDRAM_CS_CONFIG_EN) &&
+	    (ddr->cs[1].config & SDRAM_CS_CONFIG_EN) &&
+	    (ddr->cs[2].config & SDRAM_CS_CONFIG_EN) &&
+	    (ddr->cs[3].config & SDRAM_CS_CONFIG_EN))
+		four_cs = true;
+#endif
 	if (ddr->cs[0].config & SDRAM_CS_CONFIG_EN) {
 		esdmode5 = 0x00000500;	/* Data mask enable, RTT_PARK CS0 */
-		rtt_park = 1;
+		rtt_park = four_cs ? 0 : 1;
 	} else {
 		esdmode5 = 0x00000400;	/* Data mask enabled */
 	}
@@ -1130,7 +1155,10 @@ static void set_ddr_sdram_mode_9(fsl_ddr_cfg_regs_t *ddr,
 				 | ((esdmode5 & 0xffff) << 0)
 				);
 
-	/* only mode_9 use 0x500, others use 0x400 */
+	/* Normally only the first enabled CS use 0x500, others use 0x400
+	 * But when four chip-selects are all enabled, all mode registers
+	 * need 0x500 to park.
+	 */
 
 	debug("FSLDDR: ddr_sdram_mode_9) = 0x%08x\n", ddr->ddr_sdram_mode_9);
 	if (unq_mrs_en) {	/* unique mode registers are supported */
@@ -1138,7 +1166,7 @@ static void set_ddr_sdram_mode_9(fsl_ddr_cfg_regs_t *ddr,
 			if (!rtt_park &&
 			    (ddr->cs[i].config & SDRAM_CS_CONFIG_EN)) {
 				esdmode5 |= 0x00000500;	/* RTT_PARK */
-				rtt_park = 1;
+				rtt_park = four_cs ? 0 : 1;
 			} else {
 				esdmode5 = 0x00000400;
 			}
@@ -1186,6 +1214,9 @@ static void set_ddr_sdram_mode_10(const unsigned int ctrl_num,
 
 	esdmode6 = ((tccdl_min - 4) & 0x7) << 10;
 
+	if (popts->ddr_cdr2 & DDR_CDR2_VREF_RANGE_2)
+		esdmode6 |= 1 << 6;	/* Range 2 */
+
 	ddr->ddr_sdram_mode_10 = (0
 				 | ((esdmode6 & 0xffff) << 16)
 				 | ((esdmode7 & 0xffff) << 0)
@@ -1808,6 +1839,7 @@ static void set_timing_cfg_4(fsl_ddr_cfg_regs_t *ddr,
 	unsigned int wrt = 0; /* Write-to-read turnaround for same CS */
 	unsigned int rrt = 0; /* Read-to-read turnaround for same CS */
 	unsigned int wwt = 0; /* Write-to-write turnaround for same CS */
+	unsigned int trwt_mclk = 0;	/* ext_rwt */
 	unsigned int dll_lock = 0; /* DDR SDRAM DLL Lock Time */
 
 #if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR4)
@@ -1821,17 +1853,21 @@ static void set_timing_cfg_4(fsl_ddr_cfg_regs_t *ddr,
 		wwt = 2;	/* BL/2 + 2 clocks */
 	}
 #endif
-
 #ifdef CONFIG_SYS_FSL_DDR4
 	dll_lock = 2;	/* tDLLK = 1024 clocks */
 #elif defined(CONFIG_SYS_FSL_DDR3)
 	dll_lock = 1;	/* tDLLK = 512 clocks from spec */
 #endif
+
+	if (popts->trwt_override)
+		trwt_mclk = popts->trwt;
+
 	ddr->timing_cfg_4 = (0
 			     | ((rwt & 0xf) << 28)
 			     | ((wrt & 0xf) << 24)
 			     | ((rrt & 0xf) << 20)
 			     | ((wwt & 0xf) << 16)
+			     | ((trwt_mclk & 0xc) << 12)
 			     | (dll_lock & 0x3)
 			     );
 	debug("FSLDDR: timing_cfg_4 = 0x%08x\n", ddr->timing_cfg_4);

drivers/ddr/fsl/fsl_ddr_gen4.c

@@ -10,6 +10,7 @@
 #include <asm/processor.h>
 #include <fsl_immap.h>
 #include <fsl_ddr.h>
+#include <fsl_errata.h>
 
 #ifdef CONFIG_SYS_FSL_ERRATUM_A008511
 static void set_wait_for_bits_clear(void *ptr, u32 value, u32 bits)
@@ -48,12 +49,11 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
 	u32 temp_sdram_cfg;
 	u32 total_gb_size_per_controller;
 	int timeout;
-#if defined(CONFIG_SYS_FSL_ERRATUM_A008336) || \
-	defined(CONFIG_SYS_FSL_ERRATUM_A008514)
-	u32 *eddrtqcr1;
-#endif
 #ifdef CONFIG_SYS_FSL_ERRATUM_A008511
 	u32 temp32, mr6;
+	u32 vref_seq1[3] = {0x80, 0x96, 0x16};	/* for range 1 */
+	u32 vref_seq2[3] = {0xc0, 0xf0, 0x70};	/* for range 2 */
+	u32 *vref_seq = vref_seq1;
 #endif
 #ifdef CONFIG_FSL_DDR_BIST
 	u32 mtcr, err_detect, err_sbe;
@@ -66,36 +66,20 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
 	switch (ctrl_num) {
 	case 0:
 		ddr = (void *)CONFIG_SYS_FSL_DDR_ADDR;
-#if defined(CONFIG_SYS_FSL_ERRATUM_A008336) || \
-	defined(CONFIG_SYS_FSL_ERRATUM_A008514)
-		eddrtqcr1 = (void *)CONFIG_SYS_FSL_DCSR_DDR_ADDR + 0x800;
-#endif
 		break;
 #if defined(CONFIG_SYS_FSL_DDR2_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 1)
 	case 1:
 		ddr = (void *)CONFIG_SYS_FSL_DDR2_ADDR;
-#if defined(CONFIG_SYS_FSL_ERRATUM_A008336) || \
-	defined(CONFIG_SYS_FSL_ERRATUM_A008514)
-		eddrtqcr1 = (void *)CONFIG_SYS_FSL_DCSR_DDR2_ADDR + 0x800;
-#endif
 		break;
 #endif
 #if defined(CONFIG_SYS_FSL_DDR3_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 2)
 	case 2:
 		ddr = (void *)CONFIG_SYS_FSL_DDR3_ADDR;
-#if defined(CONFIG_SYS_FSL_ERRATUM_A008336) || \
-	defined(CONFIG_SYS_FSL_ERRATUM_A008514)
-		eddrtqcr1 = (void *)CONFIG_SYS_FSL_DCSR_DDR3_ADDR + 0x800;
-#endif
 		break;
 #endif
 #if defined(CONFIG_SYS_FSL_DDR4_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 3)
 	case 3:
 		ddr = (void *)CONFIG_SYS_FSL_DDR4_ADDR;
-#if defined(CONFIG_SYS_FSL_ERRATUM_A008336) || \
-	defined(CONFIG_SYS_FSL_ERRATUM_A008514)
-		eddrtqcr1 = (void *)CONFIG_SYS_FSL_DCSR_DDR4_ADDR + 0x800;
-#endif
 		break;
 #endif
 	default:
@@ -106,20 +90,6 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
 	if (step == 2)
 		goto step2;
 
-#ifdef CONFIG_SYS_FSL_ERRATUM_A008336
-#if defined(CONFIG_LS2080A) || defined(CONFIG_LS2085A)
-	/* A008336 only applies to general DDR controllers */
-	if ((ctrl_num == 0) || (ctrl_num == 1))
-#endif
-		ddr_out32(eddrtqcr1, 0x63b30002);
-#endif
-#ifdef CONFIG_SYS_FSL_ERRATUM_A008514
-#if defined(CONFIG_LS2080A) || defined(CONFIG_LS2085A)
-	/* A008514 only applies to DP-DDR controler */
-	if (ctrl_num == 2)
-#endif
-		ddr_out32(eddrtqcr1, 0x63b20002);
-#endif
 	if (regs->ddr_eor)
 		ddr_out32(&ddr->eor, regs->ddr_eor);
 
@@ -235,9 +205,11 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
 	/* Erratum applies when accumulated ECC is used, or DBI is enabled */
 #define IS_ACC_ECC_EN(v) ((v) & 0x4)
 #define IS_DBI(v) ((((v) >> 12) & 0x3) == 0x2)
-	if (IS_ACC_ECC_EN(regs->ddr_sdram_cfg) ||
-	    IS_DBI(regs->ddr_sdram_cfg_3))
-		ddr_setbits32(ddr->debug[28], 0x9 << 20);
+	if (has_erratum_a008378()) {
+		if (IS_ACC_ECC_EN(regs->ddr_sdram_cfg) ||
+		    IS_DBI(regs->ddr_sdram_cfg_3))
+			ddr_setbits32(&ddr->debug[28], 0x9 << 20);
+	}
 #endif
 
 #ifdef CONFIG_SYS_FSL_ERRATUM_A008511
@@ -307,16 +279,21 @@ step2:
 	/* This erraum only applies to verion 5.2.0 */
 	if (fsl_ddr_get_version(ctrl_num) == 0x50200) {
 		/* Wait for idle */
-		timeout = 200;
+		timeout = 40;
 		while (!(ddr_in32(&ddr->debug[1]) & 0x2) &&
 		       (timeout > 0)) {
-			udelay(100);
+			udelay(1000);
 			timeout--;
 		}
 		if (timeout <= 0) {
 			printf("Controler %d timeout, debug_2 = %x\n",
 			       ctrl_num, ddr_in32(&ddr->debug[1]));
 		}
+
+		/* The vref setting sequence is different for range 2 */
+		if (regs->ddr_cdr2 & DDR_CDR2_VREF_RANGE_2)
+			vref_seq = vref_seq2;
+
 		/* Set VREF */
 		for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
 			if (!(regs->cs[i].config & SDRAM_CS_CONFIG_EN))
@@ -327,17 +304,17 @@ step2:
 				 MD_CNTL_CS_SEL(i)			|
 				 MD_CNTL_MD_SEL(6)			|
 				 0x00200000;
-			temp32 = mr6 | 0xc0;
+			temp32 = mr6 | vref_seq[0];
 			set_wait_for_bits_clear(&ddr->sdram_md_cntl,
 						temp32, MD_CNTL_MD_EN);
 			udelay(1);
 			debug("MR6 = 0x%08x\n", temp32);
-			temp32 = mr6 | 0xf0;
+			temp32 = mr6 | vref_seq[1];
 			set_wait_for_bits_clear(&ddr->sdram_md_cntl,
 						temp32, MD_CNTL_MD_EN);
 			udelay(1);
 			debug("MR6 = 0x%08x\n", temp32);
-			temp32 = mr6 | 0x70;
+			temp32 = mr6 | vref_seq[2];
 			set_wait_for_bits_clear(&ddr->sdram_md_cntl,
 						temp32, MD_CNTL_MD_EN);
 			udelay(1);
@@ -347,10 +324,10 @@ step2:
 		ddr_out32(&ddr->debug[28], 0);		/* Enable deskew */
 		ddr_out32(&ddr->debug[1], 0x400);	/* restart deskew */
 		/* wait for idle */
-		timeout = 200;
+		timeout = 40;
 		while (!(ddr_in32(&ddr->debug[1]) & 0x2) &&
 		       (timeout > 0)) {
-			udelay(100);
+			udelay(1000);
 			timeout--;
 		}
 		if (timeout <= 0) {

drivers/ddr/fsl/options.c

@@ -29,7 +29,240 @@ struct dynamic_odt {
 	unsigned int odt_rtt_wr;
 };
 
-#if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR4)
+#ifdef CONFIG_SYS_FSL_DDR4
+/* Quad rank is not verified yet due availability.
+ * Replacing 20 OHM with 34 OHM since DDR4 doesn't have 20 OHM option
+ */
+static const struct dynamic_odt single_Q[4] = {
+	{	/* cs0 */
+		FSL_DDR_ODT_NEVER,
+		FSL_DDR_ODT_CS_AND_OTHER_DIMM,
+		DDR4_RTT_34_OHM,	/* unverified */
+		DDR4_RTT_120_OHM
+	},
+	{	/* cs1 */
+		FSL_DDR_ODT_NEVER,
+		FSL_DDR_ODT_NEVER,
+		DDR4_RTT_OFF,
+		DDR4_RTT_120_OHM
+	},
+	{	/* cs2 */
+		FSL_DDR_ODT_NEVER,
+		FSL_DDR_ODT_CS_AND_OTHER_DIMM,
+		DDR4_RTT_34_OHM,
+		DDR4_RTT_120_OHM
+	},
+	{	/* cs3 */
+		FSL_DDR_ODT_NEVER,
+		FSL_DDR_ODT_NEVER,	/* tied high */
+		DDR4_RTT_OFF,
+		DDR4_RTT_120_OHM
+	}
+};
+
+static const struct dynamic_odt single_D[4] = {
+	{	/* cs0 */
+		FSL_DDR_ODT_NEVER,
+		FSL_DDR_ODT_ALL,
+		DDR4_RTT_40_OHM,
+		DDR4_RTT_OFF
+	},
+	{	/* cs1 */
+		FSL_DDR_ODT_NEVER,
+		FSL_DDR_ODT_NEVER,
+		DDR4_RTT_OFF,
+		DDR4_RTT_OFF
+	},
+	{0, 0, 0, 0},
+	{0, 0, 0, 0}
+};
+
+static const struct dynamic_odt single_S[4] = {
+	{	/* cs0 */
+		FSL_DDR_ODT_NEVER,
+		FSL_DDR_ODT_ALL,
+		DDR4_RTT_40_OHM,
+		DDR4_RTT_OFF
+	},
+	{0, 0, 0, 0},
+	{0, 0, 0, 0},
+	{0, 0, 0, 0},
+};
+
+static const struct dynamic_odt dual_DD[4] = {
+	{	/* cs0 */
+		FSL_DDR_ODT_NEVER,
+		FSL_DDR_ODT_SAME_DIMM,
+		DDR4_RTT_120_OHM,
+		DDR4_RTT_OFF
+	},
+	{	/* cs1 */
+		FSL_DDR_ODT_OTHER_DIMM,
+		FSL_DDR_ODT_OTHER_DIMM,
+		DDR4_RTT_34_OHM,
+		DDR4_RTT_OFF
+	},
+	{	/* cs2 */
+		FSL_DDR_ODT_NEVER,
+		FSL_DDR_ODT_SAME_DIMM,
+		DDR4_RTT_120_OHM,
+		DDR4_RTT_OFF
+	},
+	{	/* cs3 */
+		FSL_DDR_ODT_OTHER_DIMM,
+		FSL_DDR_ODT_OTHER_DIMM,
+		DDR4_RTT_34_OHM,
+		DDR4_RTT_OFF
+	}
+};
+
+static const struct dynamic_odt dual_DS[4] = {
+	{	/* cs0 */
+		FSL_DDR_ODT_NEVER,
+		FSL_DDR_ODT_SAME_DIMM,
+		DDR4_RTT_120_OHM,
+		DDR4_RTT_OFF
+	},
+	{	/* cs1 */
+		FSL_DDR_ODT_OTHER_DIMM,
+		FSL_DDR_ODT_OTHER_DIMM,
+		DDR4_RTT_34_OHM,
+		DDR4_RTT_OFF
+	},
+	{	/* cs2 */
+		FSL_DDR_ODT_OTHER_DIMM,
+		FSL_DDR_ODT_ALL,
+		DDR4_RTT_34_OHM,
+		DDR4_RTT_120_OHM
+	},
+	{0, 0, 0, 0}
+};
+static const struct dynamic_odt dual_SD[4] = {
+	{	/* cs0 */
+		FSL_DDR_ODT_OTHER_DIMM,
+		FSL_DDR_ODT_ALL,
+		DDR4_RTT_34_OHM,
+		DDR4_RTT_120_OHM
+	},
+	{0, 0, 0, 0},
+	{	/* cs2 */
+		FSL_DDR_ODT_NEVER,
+		FSL_DDR_ODT_SAME_DIMM,
+		DDR4_RTT_120_OHM,
+		DDR4_RTT_OFF
+	},
+	{	/* cs3 */
+		FSL_DDR_ODT_OTHER_DIMM,
+		FSL_DDR_ODT_OTHER_DIMM,
+		DDR4_RTT_34_OHM,
+		DDR4_RTT_OFF
+	}
+};
+
+static const struct dynamic_odt dual_SS[4] = {
+	{	/* cs0 */
+		FSL_DDR_ODT_OTHER_DIMM,
+		FSL_DDR_ODT_ALL,
+		DDR4_RTT_34_OHM,
+		DDR4_RTT_120_OHM
+	},
+	{0, 0, 0, 0},
+	{	/* cs2 */
+		FSL_DDR_ODT_OTHER_DIMM,
+		FSL_DDR_ODT_ALL,
+		DDR4_RTT_34_OHM,
+		DDR4_RTT_120_OHM
+	},
+	{0, 0, 0, 0}
+};
+
+static const struct dynamic_odt dual_D0[4] = {
+	{	/* cs0 */
+		FSL_DDR_ODT_NEVER,
+		FSL_DDR_ODT_SAME_DIMM,
+		DDR4_RTT_40_OHM,
+		DDR4_RTT_OFF
+	},
+	{	/* cs1 */
+		FSL_DDR_ODT_NEVER,
+		FSL_DDR_ODT_NEVER,
+		DDR4_RTT_OFF,
+		DDR4_RTT_OFF
+	},
+	{0, 0, 0, 0},
+	{0, 0, 0, 0}
+};
+
+static const struct dynamic_odt dual_0D[4] = {
+	{0, 0, 0, 0},
+	{0, 0, 0, 0},
+	{	/* cs2 */
+		FSL_DDR_ODT_NEVER,
+		FSL_DDR_ODT_SAME_DIMM,
+		DDR4_RTT_40_OHM,
+		DDR4_RTT_OFF
+	},
+	{	/* cs3 */
+		FSL_DDR_ODT_NEVER,
+		FSL_DDR_ODT_NEVER,
+		DDR4_RTT_OFF,
+		DDR4_RTT_OFF
+	}
+};
+
+static const struct dynamic_odt dual_S0[4] = {
+	{	/* cs0 */
+		FSL_DDR_ODT_NEVER,
+		FSL_DDR_ODT_CS,
+		DDR4_RTT_40_OHM,
+		DDR4_RTT_OFF
+	},
+	{0, 0, 0, 0},
+	{0, 0, 0, 0},
+	{0, 0, 0, 0}
+
+};
+
+static const struct dynamic_odt dual_0S[4] = {
+	{0, 0, 0, 0},
+	{0, 0, 0, 0},
+	{	/* cs2 */
+		FSL_DDR_ODT_NEVER,
+		FSL_DDR_ODT_CS,
+		DDR4_RTT_40_OHM,
+		DDR4_RTT_OFF
+	},
+	{0, 0, 0, 0}
+
+};
+
+static const struct dynamic_odt odt_unknown[4] = {
+	{	/* cs0 */
+		FSL_DDR_ODT_NEVER,
+		FSL_DDR_ODT_CS,
+		DDR4_RTT_120_OHM,
+		DDR4_RTT_OFF
+	},
+	{	/* cs1 */
+		FSL_DDR_ODT_NEVER,
+		FSL_DDR_ODT_CS,
+		DDR4_RTT_120_OHM,
+		DDR4_RTT_OFF
+	},
+	{	/* cs2 */
+		FSL_DDR_ODT_NEVER,
+		FSL_DDR_ODT_CS,
+		DDR4_RTT_120_OHM,
+		DDR4_RTT_OFF
+	},
+	{	/* cs3 */
+		FSL_DDR_ODT_NEVER,
+		FSL_DDR_ODT_CS,
+		DDR4_RTT_120_OHM,
+		DDR4_RTT_OFF
+	}
+};
+#elif defined(CONFIG_SYS_FSL_DDR3)
 static const struct dynamic_odt single_Q[4] = {
 	{	/* cs0 */
 		FSL_DDR_ODT_NEVER,
@@ -259,7 +492,7 @@ static const struct dynamic_odt odt_unknown[4] = {
 		DDR3_RTT_OFF
 	}
 };
-#else	/* CONFIG_SYS_FSL_DDR3 || CONFIG_SYS_FSL_DDR4 */
+#else	/* CONFIG_SYS_FSL_DDR3 */
 static const struct dynamic_odt single_Q[4] = {
 	{0, 0, 0, 0},
 	{0, 0, 0, 0},

drivers/net/fsl-mc/dpio/qbman_portal.c

@@ -117,7 +117,7 @@ void qbman_swp_mc_submit(struct qbman_swp *p, void *cmd, uint32_t cmd_verb)
 {
 	uint32_t *v = cmd;
 #ifdef QBMAN_CHECKING
-	BUG_ON(!p->mc.check != swp_mc_can_submit);
+	BUG_ON(p->mc.check != swp_mc_can_submit);
 #endif
 	lwsync();
 	/* TBD: "|=" is going to hurt performance. Need to move as many fields

drivers/spi/fsl_qspi.c

@@ -13,6 +13,7 @@
 #include <linux/sizes.h>
 #include <dm.h>
 #include <errno.h>
+#include <watchdog.h>
 #include "fsl_qspi.h"
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -527,6 +528,8 @@ static void qspi_op_read(struct fsl_qspi_priv *priv, u32 *rxbuf, u32 len)
 	to_or_from = priv->sf_addr + priv->cur_amba_base;
 
 	while (len > 0) {
+		WATCHDOG_RESET();
+
 		qspi_write32(priv->flags, &regs->sfar, to_or_from);
 
 		size = (len > RX_BUFFER_SIZE) ?
@@ -574,6 +577,8 @@ static void qspi_op_write(struct fsl_qspi_priv *priv, u8 *txbuf, u32 len)
 
 	status_reg = 0;
 	while ((status_reg & FLASH_STATUS_WEL) != FLASH_STATUS_WEL) {
+		WATCHDOG_RESET();
+
 		qspi_write32(priv->flags, &regs->ipcr,
 			     (SEQID_WREN << QSPI_IPCR_SEQID_SHIFT) | 0);
 		while (qspi_read32(priv->flags, &regs->sr) & QSPI_SR_BUSY_MASK)

include/asm-generic/global_data.h

@@ -59,6 +59,20 @@ typedef struct global_data {
 
 	unsigned long relocaddr;	/* Start address of U-Boot in RAM */
 	phys_size_t ram_size;	/* RAM size */
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+#define MEM_RESERVE_SECURE_SECURED	0x1
+#define MEM_RESERVE_SECURE_MAINTAINED	0x2
+#define MEM_RESERVE_SECURE_ADDR_MASK	(~0x3)
+	/*
+	 * Secure memory addr
+	 * This variable needs maintenance if the RAM base is not zero,
+	 * or if RAM splits into non-consecutive banks. It also has a
+	 * flag indicating the secure memory is marked as secure by MMU.
+	 * Flags used: 0x1 secured
+	 *             0x2 maintained
+	 */
+	phys_addr_t secure_ram;
+#endif
 	unsigned long mon_len;	/* monitor len */
 	unsigned long irq_sp;		/* irq stack pointer */
 	unsigned long start_addr_sp;	/* start_addr_stackpointer */

include/compiler.h

@@ -115,9 +115,6 @@ typedef unsigned int uint;
 #ifdef CONFIG_USE_STDINT
 /* Provided by gcc. */
 #include <stdint.h>
-#else
-/* Type for `void *' pointers. */
-typedef unsigned long int uintptr_t;
 #endif
 
 #include <linux/string.h>

include/configs/ls1043a_common.h

@@ -44,6 +44,7 @@
 #define CONFIG_SYS_DDR_SDRAM_BASE	0x80000000
 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_SYS_DDR_BLOCK2_BASE      0x880000000ULL
 
 #define CPU_RELEASE_ADDR               secondary_boot_func
 

include/configs/ls1043aqds.h

@@ -88,6 +88,23 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/ls1043aqds/ls1043aqds_rcw_sd_ifc.cfg
 #endif
 
+/* SATA */
+#define CONFIG_LIBATA
+#define CONFIG_SCSI_AHCI
+#define CONFIG_SCSI_AHCI_PLAT
+#define CONFIG_CMD_SCSI
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_EXT2
+#define CONFIG_DOS_PARTITION
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_SYS_SATA				AHCI_BASE_ADDR
+
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID		1
+#define CONFIG_SYS_SCSI_MAX_LUN			1
+#define CONFIG_SYS_SCSI_MAX_DEVICE		(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+						CONFIG_SYS_SCSI_MAX_LUN)
+
 /*
  * IFC Definitions
  */

include/configs/ls1043ardb.h

@@ -27,7 +27,7 @@
 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
 /* Physical Memory Map */
 #define CONFIG_CHIP_SELECTS_PER_CTRL	4
-#define CONFIG_NR_DRAM_BANKS		1
+#define CONFIG_NR_DRAM_BANKS		2
 
 #define CONFIG_SYS_SPD_BUS_NUM		0
 
@@ -291,4 +291,14 @@
 #define CONFIG_CMD_EXT2
 #endif
 
+#ifdef CONFIG_SECURE_BOOT
+#define CONFIG_CMD_HASH
+#define CONFIG_SHA_HW_ACCEL
+#define CONFIG_CMD_BLOB
+/* For LS1043 (ARMv8), ESBC image Address in Header is 64 bit */
+#define CONFIG_ESBC_ADDR_64BIT
+#endif
+
+#include <asm/fsl_secure_boot.h>
+
 #endif /* __LS1043ARDB_H__ */

include/configs/ls2080a_common.h

@@ -195,10 +195,9 @@ unsigned long long get_qixis_addr(void);
  * 512MB aligned, so the min size to hide is 512MB.
  */
 #if defined(CONFIG_FSL_MC_ENET) || defined(CONFIG_FSL_DEBUG_SERVER)
-#define CONFIG_SYS_DEBUG_SERVER_DRAM_BLOCK_MIN_SIZE	(256UL * 1024 * 1024)
+#define CONFIG_SYS_DEBUG_SERVER_DRAM_BLOCK_MIN_SIZE	(254UL * 1024 * 1024)
 #define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE		(256UL * 1024 * 1024)
-#define CONFIG_SYS_MEM_TOP_HIDE_MIN			(512UL * 1024 * 1024)
-#define CONFIG_SYS_MEM_TOP_HIDE		get_dram_size_to_hide()
+#define CONFIG_SYS_MC_RSV_MEM_ALIGN			(512UL * 1024 * 1024)
 #endif
 
 /* PCIe */
@@ -271,7 +270,7 @@ unsigned long long get_qixis_addr(void);
 	"console=ttyAMA0,38400n8\0"
 
 #define CONFIG_BOOTARGS		"console=ttyS0,115200 root=/dev/ram0 " \
-				"earlycon=uart8250,mmio,0x21c0500,115200 " \
+				"earlycon=uart8250,mmio,0x21c0500" \
 				"ramdisk_size=0x2000000 default_hugepagesz=2m" \
 				" hugepagesz=2m hugepages=16"
 #define CONFIG_BOOTCOMMAND		"cp.b $kernel_start $kernel_load "     \
@@ -290,10 +289,6 @@ unsigned long long get_qixis_addr(void);
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_SYS_MAXARGS		64	/* max command args */
 
-#ifndef __ASSEMBLY__
-unsigned long get_dram_size_to_hide(void);
-#endif
-
 #define CONFIG_PANIC_HANG	/* do not reset board on panic */
 
 #define CONFIG_SPL_BSS_START_ADDR	0x80100000

include/configs/ls2080aqds.h

@@ -40,6 +40,24 @@ unsigned long get_board_ddr_clk(void);
 #endif
 #define CONFIG_FSL_DDR_BIST	/* enable built-in memory test */
 
+/* SATA */
+#define CONFIG_LIBATA
+#define CONFIG_SCSI_AHCI
+#define CONFIG_SCSI_AHCI_PLAT
+#define CONFIG_CMD_SCSI
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_EXT2
+#define CONFIG_DOS_PARTITION
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_SYS_SATA1			AHCI_BASE_ADDR1
+#define CONFIG_SYS_SATA2			AHCI_BASE_ADDR2
+
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID		1
+#define CONFIG_SYS_SCSI_MAX_LUN			1
+#define CONFIG_SYS_SCSI_MAX_DEVICE		(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+						CONFIG_SYS_SCSI_MAX_LUN)
+
 /* undefined CONFIG_FSL_DDR_SYNC_REFRESH for simulator */
 
 #define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)

include/configs/ls2080ardb.h

@@ -42,6 +42,24 @@ unsigned long get_board_sys_clk(void);
 #endif
 #define CONFIG_FSL_DDR_BIST	/* enable built-in memory test */
 
+/* SATA */
+#define CONFIG_LIBATA
+#define CONFIG_SCSI_AHCI
+#define CONFIG_SCSI_AHCI_PLAT
+#define CONFIG_CMD_SCSI
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_EXT2
+#define CONFIG_DOS_PARTITION
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_SYS_SATA1			AHCI_BASE_ADDR1
+#define CONFIG_SYS_SATA2			AHCI_BASE_ADDR2
+
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID		1
+#define CONFIG_SYS_SCSI_MAX_LUN			1
+#define CONFIG_SYS_SCSI_MAX_DEVICE		(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+						CONFIG_SYS_SCSI_MAX_LUN)
+
 /* undefined CONFIG_FSL_DDR_SYNC_REFRESH for simulator */
 
 #define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
@@ -313,7 +331,7 @@ unsigned long get_board_sys_clk(void);
 
 #undef CONFIG_BOOTARGS
 #define CONFIG_BOOTARGS		"console=ttyS1,115200 root=/dev/ram0 " \
-				"earlycon=uart8250,mmio,0x21c0600,115200 " \
+				"earlycon=uart8250,mmio,0x21c0600" \
 				"ramdisk_size=0x2000000 default_hugepagesz=2m" \
 				" hugepagesz=2m hugepages=16"
 

include/fsl_ddr_sdram.h

@@ -33,6 +33,15 @@
 #define DDR3_RTT_20_OHM		4 /* RTT_Nom = RZQ/12 */
 #define DDR3_RTT_30_OHM		5 /* RTT_Nom = RZQ/8 */
 
+#define DDR4_RTT_OFF		0
+#define DDR4_RTT_60_OHM		1	/* RZQ/4 */
+#define DDR4_RTT_120_OHM	2	/* RZQ/2 */
+#define DDR4_RTT_40_OHM		3	/* RZQ/6 */
+#define DDR4_RTT_240_OHM	4	/* RZQ/1 */
+#define DDR4_RTT_48_OHM		5	/* RZQ/5 */
+#define DDR4_RTT_80_OHM		6	/* RZQ/3 */
+#define DDR4_RTT_34_OHM		7	/* RZQ/7 */
+
 #define DDR2_RTT_OFF		0
 #define DDR2_RTT_75_OHM		1
 #define DDR2_RTT_150_OHM	2

arch/powerpc/include/asm/fsl_errata.h → include/fsl_errata.h

@@ -1,14 +1,21 @@
 /*
- * Copyright 2013 Freescale Semiconductor, Inc.
+ * Copyright 2013 - 2015  Freescale Semiconductor, Inc.
  *
  * SPDX-License-Identifier:    GPL-2.0+
  */
 
-#ifndef _ASM_FSL_ERRATA_H
-#define _ASM_FSL_ERRATA_H
+#ifndef _FSL_ERRATA_H
+#define _FSL_ERRATA_H
 
 #include <common.h>
+#if defined(CONFIG_PPC)
 #include <asm/processor.h>
+#elif defined(CONFIG_LS102XA)
+#include <asm/arch-ls102xa/immap_ls102xa.h>
+#elif defined(CONFIG_FSL_LAYERSCAPE)
+#include <asm/arch/soc.h>
+#endif
+
 
 #ifdef CONFIG_SYS_FSL_ERRATUM_A006379
 static inline bool has_erratum_a006379(void)
@@ -26,7 +33,6 @@ static inline bool has_erratum_a006379(void)
 	return false;
 }
 #endif
-#endif
 
 #ifdef CONFIG_SYS_FSL_ERRATUM_A007186
 static inline bool has_erratum_a007186(void)
@@ -51,3 +57,36 @@ static inline bool has_erratum_a007186(void)
 	return false;
 }
 #endif
+
+#ifdef CONFIG_SYS_FSL_ERRATUM_A008378
+static inline bool has_erratum_a008378(void)
+{
+	u32 svr = get_svr();
+	u32 soc = SVR_SOC_VER(svr);
+
+
+	switch (soc) {
+#ifdef CONFIG_LS102XA
+	case SOC_VER_LS1020:
+	case SOC_VER_LS1021:
+	case SOC_VER_LS1022:
+	case SOC_VER_SLS1020:
+		return IS_SVR_REV(svr, 1, 0);
+#endif
+#ifdef CONFIG_PPC
+	case SVR_T1023:
+	case SVR_T1024:
+		return IS_SVR_REV(svr, 1, 0);
+	case SVR_T1020:
+	case SVR_T1022:
+	case SVR_T1040:
+	case SVR_T1042:
+		return IS_SVR_REV(svr, 1, 0) || IS_SVR_REV(svr, 1, 1);
+#endif
+	default:
+		return false;
+	}
+}
+#endif
+
+#endif /*  _FSL_ERRATA_H */

include/fsl_validate.h

@@ -83,7 +83,9 @@ struct fsl_secboot_img_hdr {
 	u32 sign_len;		/* length of the signature in bytes */
 	union {
 		u32 psgtable;	/* ptr to SG table */
+#ifndef CONFIG_ESBC_ADDR_64BIT
 		u32 pimg;	/* ptr to ESBC client image */
+#endif
 	};
 	union {
 		u32 sg_entries;	/* no of entries in SG table */
@@ -97,7 +99,12 @@ struct fsl_secboot_img_hdr {
 	u32 reserved1[2];
 	u32 fsl_uid_1;
 	u32 oem_uid_1;
-	u32 reserved2[2];
+	union {
+		u32 reserved2[2];
+#ifdef CONFIG_ESBC_ADDR_64BIT
+		u64 pimg64;	/* 64 bit pointer to ESBC Image */
+#endif
+	};
 	u32 ie_flag;
 	u32 ie_key_sel;
 };

include/linux/types.h

@@ -124,6 +124,7 @@ typedef		__UINT64_TYPE__	u_int64_t;
 typedef		__INT64_TYPE__		int64_t;
 #endif
 
+typedef unsigned long uintptr_t;
 /*
  * Below are truly Linux-specific types that should never collide with
  * any application/library that wants linux/types.h.