mx1ads: remove board support

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Stefano Babic <sbabic@denx.de>

board/mx1ads/Makefile

@@ -1,16 +0,0 @@
-#
-# board/mx1ads/Makefile
-#
-# (C) Copyright 2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# (c) Copyright 2004
-# Techware Information Technology, Inc.
-# http://www.techware.com.tw/
-#
-# Ming-Len Wu <minglen_wu@techware.com.tw>
-#
-# SPDX-License-Identifier:	GPL-2.0+
-
-obj-y	:= mx1ads.o syncflash.o
-obj-y	+= lowlevel_init.o

board/mx1ads/lowlevel_init.S

@@ -1,68 +0,0 @@
-/*
- * board/mx1ads/lowlevel_init.S
- *
- * (c) Copyright 2004
- * Techware Information Technology, Inc.
- * http://www.techware.com.tw/
- *
- * Ming-Len Wu <minglen_wu@techware.com.tw>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <config.h>
-#include <version.h>
-
-#define SDCTL0			0x221000
-#define SDCTL1			0x221004
-
-
-_TEXT_BASE:
-	.word	CONFIG_SYS_TEXT_BASE
-
-.globl lowlevel_init
-lowlevel_init:
-/* memory controller init		*/
-
-	ldr  r1, =SDCTL0
-
-/*  Set Precharge Command		*/
-
-	ldr  r3, =0x92120200
-/*	ldr  r3, =0x92120251
-*/
-	str  r3, [r1]
-
-/* Issue Precharge All Commad		*/
-	ldr  r3, =0x8200000
-	ldr  r2, [r3]
-
-/* Set AutoRefresh Command		*/
-	ldr  r3, =0xA2120200
-	str  r3, [r1]
-
-/* Issue AutoRefresh Command		*/
-	ldr  r3, =0x8000000
-	ldr  r2, [r3]
-	ldr  r2, [r3]
-	ldr  r2, [r3]
-	ldr  r2, [r3]
-	ldr  r2, [r3]
-	ldr  r2, [r3]
-	ldr  r2, [r3]
-	ldr  r2, [r3]
-
-/* Set Mode Register			*/
-	ldr  r3, =0xB2120200
-	str  r3, [r1]
-
-/* Issue Mode Register Command		*/
-	ldr  r3, =0x08111800	/* Mode Register Value		*/
-	ldr  r2, [r3]
-
-/* Set Normal Mode			*/
-	ldr  r3, =0x82124200
-	str  r3, [r1]
-
-/* everything is fine now		*/
-	mov	pc, lr

board/mx1ads/mx1ads.c

@@ -1,178 +0,0 @@
-/*
- * board/mx1ads/mx1ads.c
- *
- * (c) Copyright 2004
- * Techware Information Technology, Inc.
- * http://www.techware.com.tw/
- *
- * Ming-Len Wu <minglen_wu@techware.com.tw>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <netdev.h>
-/*#include <mc9328.h>*/
-#include <asm/arch/imx-regs.h>
-#include <asm/io.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define FCLK_SPEED 1
-
-#if FCLK_SPEED==0		/* Fout = 203MHz, Fin = 12MHz for Audio */
-#define M_MDIV	0xC3
-#define M_PDIV	0x4
-#define M_SDIV	0x1
-#elif FCLK_SPEED==1		/* Fout = 202.8MHz */
-#define M_MDIV	0xA1
-#define M_PDIV	0x3
-#define M_SDIV	0x1
-#endif
-
-#define USB_CLOCK 1
-
-#if USB_CLOCK==0
-#define U_M_MDIV	0xA1
-#define U_M_PDIV	0x3
-#define U_M_SDIV	0x1
-#elif USB_CLOCK==1
-#define U_M_MDIV	0x48
-#define U_M_PDIV	0x3
-#define U_M_SDIV	0x2
-#endif
-
-#if 0
-
-static inline void delay (unsigned long loops)
-{
-	__asm__ volatile ("1:\n"
-			  "subs %0, %1, #1\n"
-			  "bne 1b":"=r" (loops):"0" (loops));
-}
-
-#endif
-
-/*
- * Miscellaneous platform dependent initialisations
- */
-
-void SetAsynchMode (void)
-{
-	__asm__ ("mrc p15,0,r0,c1,c0,0 \n"
-		 "mov r2, #0xC0000000 \n"
-		 "orr r0,r2,r0 \n" "mcr p15,0,r0,c1,c0,0 \n");
-}
-
-static u32 mc9328sid;
-
-int board_early_init_f(void)
-{
-	mc9328sid = SIDR;
-
-	GPCR = 0x000003AB;	/* I/O pad driving strength     */
-
-	/*	MX1_CS1U	= 0x00000A00;	*/ /* SRAM initialization          */
-/*	MX1_CS1L	= 0x11110601;	*/
-
-	MPCTL0 = 0x04632410;	/* setting for 150 MHz MCU PLL CLK      */
-
-/* set FCLK divider 1 (i.e. FCLK to MCU PLL CLK) and
- * BCLK divider to 2 (i.e. BCLK to 48 MHz)
- */
-	CSCR = 0xAF000403;
-
-	CSCR |= 0x00200000;	/* Trigger the restart bit(bit 21)      */
-	CSCR &= 0xFFFF7FFF;	/* Program PRESC bit(bit 15) to 0 to divide-by-1 */
-
-/* setup cs4 for cs8900 ethernet */
-
-	CS4U = 0x00000F00;	/* Initialize CS4 for CS8900 ethernet   */
-	CS4L = 0x00001501;
-
-	GIUS (0) &= 0xFF3FFFFF;
-	GPR (0) &= 0xFF3FFFFF;
-
-	readl(0x1500000C);
-	readl(0x1500000C);
-
-	SetAsynchMode ();
-
-	icache_enable ();
-	dcache_enable ();
-
-/* set PERCLKs				*/
-	PCDR = 0x00000055;	/* set PERCLKS                          */
-
-/* PERCLK3 is only used by SSI so the SSI driver can set it any value it likes
- * PERCLK1 and PERCLK2 are shared so DO NOT change it in any other place
- * all sources selected as normal interrupt
- */
-
-/*	MX1_INTTYPEH = 0;
-	MX1_INTTYPEL = 0;
-*/
-	return 0;
-}
-
-int board_init(void)
-{
-	gd->bd->bi_arch_number = MACH_TYPE_MX1ADS;
-
-	gd->bd->bi_boot_params = 0x08000100;	/* adress of boot parameters */
-
-	return 0;
-}
-
-int board_late_init (void)
-{
-
-	setenv ("stdout", "serial");
-	setenv ("stderr", "serial");
-
-	switch (mc9328sid) {
-	case 0x0005901d:
-		printf ("MX1ADS board with MC9328 MX1 (0L44N), Silicon ID 0x%08x \n\n",
-			mc9328sid);
-		break;
-	case 0x04d4c01d:
-		printf ("MX1ADS board with MC9328 MXL (1L45N), Silicon ID 0x%08x \n\n",
-			mc9328sid);
-		break;
-	case 0x00d4c01d:
-		printf ("MX1ADS board with MC9328 MXL (2L45N), Silicon ID 0x%08x \n\n",
-			mc9328sid);
-		break;
-
-	default:
-		printf ("MX1ADS board with UNKNOWN MC9328 cpu, Silicon ID 0x%08x \n",
-			mc9328sid);
-		break;
-	}
-	return 0;
-}
-
-int dram_init(void)
-{
-	/* dram_init must store complete ramsize in gd->ram_size */
-	gd->ram_size = get_ram_size((void *)PHYS_SDRAM_1,
-				PHYS_SDRAM_1_SIZE);
-	return 0;
-}
-
-void dram_init_banksize(void)
-{
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-}
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
-	int rc = 0;
-#ifdef CONFIG_CS8900
-	rc = cs8900_initialize(0, CONFIG_CS8900_BASE);
-#endif
-	return rc;
-}
-#endif

board/mx1ads/syncflash.c

@@ -1,307 +0,0 @@
-/*
- * board/mx1ads/syncflash.c
- *
- * (c) Copyright 2004
- * Techware Information Technology, Inc.
- * http://www.techware.com.tw/
- *
- * Ming-Len Wu <minglen_wu@techware.com.tw>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-/*#include <mc9328.h>*/
-#include <asm/arch/imx-regs.h>
-
-typedef unsigned long * p_u32;
-
-/* 4Mx16x2 IAM=0 CSD1 */
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];	/* info for FLASH chips    */
-
-/*  Following Setting is for CSD1	*/
-#define SFCTL			0x00221004
-#define reg_SFCTL		__REG(SFCTL)
-
-#define SYNCFLASH_A10		(0x00100000)
-
-#define CMD_NORMAL		(0x81020300)			/* Normal Mode			*/
-#define CMD_PREC		(CMD_NORMAL + 0x10000000)	/* Precharge Command		*/
-#define CMD_AUTO		(CMD_NORMAL + 0x20000000)	/* Auto Refresh Command		*/
-#define CMD_LMR			(CMD_NORMAL + 0x30000000)	/* Load Mode Register Command	*/
-#define CMD_LCR			(CMD_NORMAL + 0x60000000)	/* LCR Command			*/
-#define CMD_PROGRAM		(CMD_NORMAL + 0x70000000)
-
-#define MODE_REG_VAL		(CONFIG_SYS_FLASH_BASE+0x0008CC00)	/* Cas Latency 3		*/
-
-/* LCR Command */
-#define LCR_READSTATUS		(0x0001C000)			/* 0x70				*/
-#define LCR_ERASE_CONFIRM	(0x00008000)			/* 0x20				*/
-#define LCR_ERASE_NVMODE	(0x0000C000)			/* 0x30				*/
-#define LCR_PROG_NVMODE		(0x00028000)			/* 0xA0				*/
-#define LCR_SR_CLEAR		(0x00014000)			/* 0x50				*/
-
-/* Get Status register			*/
-u32 SF_SR(void) {
-	u32 tmp;
-
-	reg_SFCTL	= CMD_PROGRAM;
-	tmp		= __REG(CONFIG_SYS_FLASH_BASE);
-
-	reg_SFCTL	= CMD_NORMAL;
-
-	reg_SFCTL	= CMD_LCR;			/* Activate LCR Mode		*/
-	__REG(CONFIG_SYS_FLASH_BASE + LCR_SR_CLEAR);
-
-	return tmp;
-}
-
-/* check if SyncFlash is ready		*/
-u8 SF_Ready(void) {
-	u32 tmp;
-
-	tmp	= SF_SR();
-
-	if ((tmp & 0x00800000) && (tmp & 0x001C0000)) {
-		printf ("SyncFlash Error code %08x\n",tmp);
-	};
-
-	if ((tmp & 0x00000080) && (tmp & 0x0000001C)) {
-		printf ("SyncFlash Error code %08x\n",tmp);
-	};
-
-	if (tmp == 0x00800080)		/* Test Bit 7 of SR	*/
-		return 1;
-	else
-		return 0;
-}
-
-/* Issue the precharge all command		*/
-void SF_PrechargeAll(void) {
-
-	/* Set Precharge Command	*/
-	reg_SFCTL	= CMD_PREC;
-	/* Issue Precharge All Command */
-	__REG(CONFIG_SYS_FLASH_BASE + SYNCFLASH_A10);
-}
-
-/* set SyncFlash to normal mode			*/
-void SF_Normal(void) {
-
-	SF_PrechargeAll();
-
-	reg_SFCTL	= CMD_NORMAL;
-}
-
-/* Erase SyncFlash				*/
-void SF_Erase(u32 RowAddress) {
-
-	reg_SFCTL	= CMD_NORMAL;
-	__REG(RowAddress);
-
-	reg_SFCTL	= CMD_PREC;
-	__REG(RowAddress);
-
-	reg_SFCTL	= CMD_LCR;			/* Set LCR mode		*/
-	__REG(RowAddress + LCR_ERASE_CONFIRM)	= 0;	/* Issue Erase Setup Command	*/
-
-	reg_SFCTL	= CMD_NORMAL;			/* return to Normal mode	*/
-	__REG(RowAddress)	= 0xD0D0D0D0;		/* Confirm			*/
-
-	while(!SF_Ready());
-}
-
-void SF_NvmodeErase(void) {
-	SF_PrechargeAll();
-
-	reg_SFCTL	= CMD_LCR;			/* Set to LCR mode		*/
-	__REG(CONFIG_SYS_FLASH_BASE + LCR_ERASE_NVMODE)  = 0;	/* Issue Erase Nvmode Reg Command */
-
-	reg_SFCTL	= CMD_NORMAL;			/* Return to Normal mode	*/
-	__REG(CONFIG_SYS_FLASH_BASE + LCR_ERASE_NVMODE) = 0xC0C0C0C0;	/* Confirm		*/
-
-	while(!SF_Ready());
-}
-
-void SF_NvmodeWrite(void) {
-	SF_PrechargeAll();
-
-	reg_SFCTL	= CMD_LCR;			/* Set to LCR mode		*/
-	__REG(CONFIG_SYS_FLASH_BASE+LCR_PROG_NVMODE) = 0;	/* Issue Program Nvmode reg command */
-
-	reg_SFCTL	= CMD_NORMAL;			/* Return to Normal mode	*/
-	__REG(CONFIG_SYS_FLASH_BASE+LCR_PROG_NVMODE) = 0xC0C0C0C0;	/* Confirm not needed	*/
-}
-
-/****************************************************************************************/
-
-ulong flash_init(void) {
-	int i, j;
-
-/* Turn on CSD1 for negating RESETSF of SyncFLash */
-
-	reg_SFCTL	|= 0x80000000;		/* enable CSD1 for SyncFlash		*/
-	udelay(200);
-
-	reg_SFCTL	= CMD_LMR;		/* Set Load Mode Register Command	*/
-	__REG(MODE_REG_VAL);	/* Issue Load Mode Register Command	*/
-
-	SF_Normal();
-
-	i = 0;
-
-	flash_info[i].flash_id	=  FLASH_MAN_MT | FLASH_MT28S4M16LC;
-
-	flash_info[i].size	= FLASH_BANK_SIZE;
-	flash_info[i].sector_count = CONFIG_SYS_MAX_FLASH_SECT;
-
-	memset(flash_info[i].protect, 0, CONFIG_SYS_MAX_FLASH_SECT);
-
-	for (j = 0; j < flash_info[i].sector_count; j++) {
-		flash_info[i].start[j] = CONFIG_SYS_FLASH_BASE + j * 0x00100000;
-	}
-
-	flash_protect(FLAG_PROTECT_SET,
-		CONFIG_SYS_FLASH_BASE,
-		CONFIG_SYS_FLASH_BASE + monitor_flash_len - 1,
-		&flash_info[0]);
-
-	flash_protect(FLAG_PROTECT_SET,
-		CONFIG_ENV_ADDR,
-		CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1,
-		&flash_info[0]);
-
-	return FLASH_BANK_SIZE;
-}
-
-void flash_print_info (flash_info_t *info) {
-
-	int i;
-
-	switch (info->flash_id & FLASH_VENDMASK) {
-		case (FLASH_MAN_MT & FLASH_VENDMASK):
-			printf("Micron: ");
-			break;
-		default:
-			printf("Unknown Vendor ");
-			break;
-	}
-
-	switch (info->flash_id & FLASH_TYPEMASK) {
-		case (FLASH_MT28S4M16LC & FLASH_TYPEMASK):
-			printf("2x FLASH_MT28S4M16LC (16MB Total)\n");
-			break;
-		default:
-			printf("Unknown Chip Type\n");
-			return;
-			break;
-	}
-
-	printf("  Size: %ld MB in %d Sectors\n",
-		info->size >> 20, info->sector_count);
-
-	printf("  Sector Start Addresses: ");
-
-	for (i = 0; i < info->sector_count; i++) {
-		if ((i % 5) == 0)
-			printf ("\n   ");
-
-		printf (" %08lX%s", info->start[i],
-			info->protect[i] ? " (RO)" : "     ");
-	}
-
-	printf ("\n");
-}
-
-/*-----------------------------------------------------------------------*/
-
-int flash_erase (flash_info_t *info, int s_first, int s_last) {
-	int iflag, cflag, prot, sect;
-	int rc = ERR_OK;
-
-/* first look for protection bits */
-
-	if (info->flash_id == FLASH_UNKNOWN)
-		return ERR_UNKNOWN_FLASH_TYPE;
-
-	if ((s_first < 0) || (s_first > s_last))
-		return ERR_INVAL;
-
-	if ((info->flash_id & FLASH_VENDMASK) != (FLASH_MAN_MT & FLASH_VENDMASK))
-		return ERR_UNKNOWN_FLASH_VENDOR;
-
-	prot = 0;
-
-	for (sect = s_first; sect <= s_last; ++sect) {
-		if (info->protect[sect])
-			prot++;
-	}
-
-	if (prot) {
-		printf("protected!\n");
-		return ERR_PROTECTED;
-	}
-/*
- * Disable interrupts which might cause a timeout
- * here. Remember that our exception vectors are
- * at address 0 in the flash, and we don't want a
- * (ticker) exception to happen while the flash
- * chip is in programming mode.
- */
-
-	cflag = icache_status();
-	icache_disable();
-	iflag = disable_interrupts();
-
-/* Start erase on unprotected sectors */
-	for (sect = s_first; sect <= s_last && !ctrlc(); sect++) {
-
-		printf("Erasing sector %2d ... ", sect);
-
-/* arm simple, non interrupt dependent timer */
-
-		get_timer(0);
-
-		SF_NvmodeErase();
-		SF_NvmodeWrite();
-
-		SF_Erase(CONFIG_SYS_FLASH_BASE + (0x0100000 * sect));
-		SF_Normal();
-
-		printf("ok.\n");
-	}
-
-	if (ctrlc())
-		printf("User Interrupt!\n");
-
-	if (iflag)
-		enable_interrupts();
-
-	if (cflag)
-		icache_enable();
-
-	return rc;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash.
- */
-
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt) {
-	int i;
-
-	for(i = 0; i < cnt; i += 4) {
-
-		SF_PrechargeAll();
-
-		reg_SFCTL	= CMD_PROGRAM;		/* Enter SyncFlash Program mode */
-		__REG(addr + i) = __REG((u32)src  + i);
-
-		while(!SF_Ready());
-	}
-
-	SF_Normal();
-
-	return ERR_OK;
-}

boards.cfg

@@ -65,7 +65,6 @@ Active  arm         arm920t        at91        BuS             eb_cpux9k2
 Active  arm         arm920t        at91        BuS             eb_cpux9k2          eb_cpux9k2_ram                       eb_cpux9k2:RAMBOOT                                                                                                                Jens Scharsig <esw@bus-elektronik.de>
 Active  arm         arm920t        at91        eukrea          cpuat91             cpuat91                              cpuat91                                                                                                                           Eric Benard <eric@eukrea.com>
 Active  arm         arm920t        at91        eukrea          cpuat91             cpuat91_ram                          cpuat91:RAMBOOT                                                                                                                   Eric Benard <eric@eukrea.com>
-Active  arm         arm920t        imx         -               -                   mx1ads                               -                                                                                                                                 -
 Active  arm         arm920t        imx         -               -                   scb9328                              -                                                                                                                                 Torsten Koschorrek <koschorrek@synertronixx.de>
 Active  arm         arm920t        ks8695      -               -                   cm4008                               -                                                                                                                                 Greg Ungerer <greg.ungerer@opengear.com>
 Active  arm         arm920t        ks8695      -               -                   cm41xx                               -                                                                                                                                 -

doc/README.scrapyard

@@ -11,6 +11,7 @@ easily if here is something they might want to dig for...
 
 Board            Arch        CPU            Commit      Removed     Last known maintainer/contact
 =================================================================================================
+mx1ads           arm         arm920t        -           2014-01-13
 mini2440         arm         arm920t        -           2014-01-13  Gabriel Huau <contact@huau-gabriel.fr>
 omap730p2        arm         arm926ejs      79c5c08d    2013-11-11
 pn62             powerpc     mpc824x        649acfe1    2013-11-11  Wolfgang Grandegger <wg@grandegger.com>

include/configs/mx1ads.h

@@ -1,163 +0,0 @@
-/*
- * include/configs/mx1ads.h
- *
- * (c) Copyright 2004
- * Techware Information Technology, Inc.
- * http://www.techware.com.tw/
- *
- * Ming-Len Wu <minglen_wu@techware.com.tw>
- *
- * This is the Configuration setting for Motorola MX1ADS board
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_ARM920T		1	/* This is an ARM920T Core		*/
-#define CONFIG_IMX		1	/* It's a Motorola MC9328 SoC		*/
-#define CONFIG_MX1ADS		1	/* on a Motorola MX1ADS Board		*/
-
-/*
- * Select serial console configuration
-  */
-#define CONFIG_IMX_SERIAL
-#define CONFIG_IMX_SERIAL1		/* internal uart 1 */
-/* #define _CONFIG_UART2 */		/* internal uart 2 */
-/* #define CONFIG_SILENT_CONSOLE */	/* use this to disable output */
-
-#define CONFIG_BOARD_LATE_INIT
-#define USE_920T_MMU		1
-
-#if 0
-#define CONFIG_SYS_MX1_GPCR		0x000003AB	/* for MX1ADS 0L44N		*/
-#define CONFIG_SYS_MX1_GPCR		0x000003AB	/* for MX1ADS 0L44N		*/
-#define CONFIG_SYS_MX1_GPCR		0x000003AB	/* for MX1ADS 0L44N		*/
-#endif
-
-/*
- * Size of malloc() pool
- */
-
-#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 128*1024)
-
-/*
- *  CS8900 Ethernet drivers
- */
-#define CONFIG_CS8900		/* we have a CS8900 on-board */
-#define CONFIG_CS8900_BASE	0x15000300
-#define CONFIG_CS8900_BUS16	/* the Linux driver does accesses as shorts */
-
-/*
- * select serial console configuration
- */
-
-/* #define CONFIG_UART1			*/
-/* #define CONFIG_UART2		1	*/
-
-#define CONFIG_BAUDRATE		115200
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_ELF
-
-#define CONFIG_BOOTDELAY	3
-#define CONFIG_BOOTARGS		"root=/dev/msdk mem=48M"
-#define CONFIG_BOOTFILE		"mx1ads"
-#define CONFIG_BOOTCOMMAND	"tftp; bootm"
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	115200		/* speed to run kgdb serial port */
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-
-#define CONFIG_SYS_HUSH_PARSER		1
-
-#define CONFIG_SYS_LONGHELP				/* undef to save memory		*/
-
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT		"MX1ADS$ "	/* Monitor Command Prompt */
-#else
-#define CONFIG_SYS_PROMPT		"MX1ADS=> "	/* Monitor Command Prompt */
-#endif
-
-#define CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
-#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-						/* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x09000000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0AF00000	/* 63 MB in DRAM	*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x08800000	/* default load address */
-#define CONFIG_SYS_HZ			3686400
-#define CONFIG_SYS_CPUSPEED		0x141
-
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-
-#define CONFIG_NR_DRAM_BANKS	1		/* we have 1 bank of SDRAM	*/
-#define PHYS_SDRAM_1		0x08000000	/* SDRAM  on CSD0		*/
-#define PHYS_SDRAM_1_SIZE	0x04000000	/* 64 MB			*/
-
-#define CONFIG_SYS_TEXT_BASE	0x10000000
-
-#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_ADDR	0x00300000
-#define CONFIG_SYS_INIT_RAM_SIZE	0x000FFFFF
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-						GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR	(CONFIG_SYS_INIT_RAM_ADDR + \
-						CONFIG_SYS_GBL_DATA_OFFSET)
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1		/* 1 bank of SyncFlash		*/
-#define CONFIG_SYS_FLASH_BASE		0x0C000000	/* SyncFlash on CSD1		*/
-#define FLASH_BANK_SIZE		0x01000000	/* 16 MB Total			*/
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-
-#define CONFIG_SYNCFLASH	1
-#define PHYS_FLASH_SIZE		0x01000000
-#define CONFIG_SYS_MAX_FLASH_SECT	(16)
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE+0x00ff8000)
-
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_SIZE		0x04000 /* Total Size of Environment Sector */
-#define CONFIG_ENV_SECT_SIZE	0x100000
-
-/*-----------------------------------------------------------------------
- * Enable passing ATAGS
- */
-
-#define CONFIG_CMDLINE_TAG		1	/* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS	1
-
-#define CONFIG_SYS_CLK_FREQ 16780000
-#define CONFIG_SYSPLL_CLK_FREQ 16000000
-
-#endif	/* __CONFIG_H */