QE/FMAN: modify CONFIG_SYS_QE_FMAN_FW_ADDR to CONFIG_SYS_FMAN_FW_ADDR and CONFIG_SYS_QE_FW_ADDR

CONFIG_SYS_QE_FMAN_FW_ADDR is used to both Fman and QE for microcode address.
Now using CONFIG_SYS_FMAN_FW_ADDR for Fman microcode address,
and CONFIG_SYS_QE_FW_ADDR for QE microcode address.

Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

README

@@ -4502,8 +4502,13 @@ This firmware often needs to be loaded during U-Boot booting, so macros
 are used to identify the storage device (NOR flash, SPI, etc) and the address
 within that device.
 
-- CONFIG_SYS_QE_FMAN_FW_ADDR
-	The address in the storage device where the firmware is located.  The
+- CONFIG_SYS_FMAN_FW_ADDR
+	The address in the storage device where the FMAN microcode is located.  The
+	meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
+	is also specified.
+
+- CONFIG_SYS_QE_FW_ADDR
+	The address in the storage device where the QE microcode is located.  The
 	meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
 	is also specified.
 

arch/powerpc/cpu/mpc85xx/cpu_init.c

@@ -818,7 +818,7 @@ void cpu_secondary_init_r(void)
 
 	/* load QE firmware from NAND flash to DDR first */
 	ret = nand_read(&nand_info[0], (loff_t)CONFIG_SYS_QE_FMAN_FW_IN_NAND,
-			&fw_length, (u_char *)CONFIG_SYS_QE_FMAN_FW_ADDR);
+			&fw_length, (u_char *)CONFIG_SYS_QE_FW_ADDR);
 
 	if (ret && ret == -EUCLEAN) {
 		printf ("NAND read for QE firmware at offset %x failed %d\n",

drivers/net/fm/fm.c

@@ -350,16 +350,16 @@ int fm_init_common(int index, struct ccsr_fman *reg)
 {
 	int rc;
 #if defined(CONFIG_SYS_QE_FMAN_FW_IN_NOR)
-	void *addr = (void *)CONFIG_SYS_QE_FMAN_FW_ADDR;
+	void *addr = (void *)CONFIG_SYS_FMAN_FW_ADDR;
 #elif defined(CONFIG_SYS_QE_FMAN_FW_IN_NAND)
 	size_t fw_length = CONFIG_SYS_QE_FMAN_FW_LENGTH;
 	void *addr = malloc(CONFIG_SYS_QE_FMAN_FW_LENGTH);
 
-	rc = nand_read(&nand_info[0], (loff_t)CONFIG_SYS_QE_FMAN_FW_ADDR,
+	rc = nand_read(&nand_info[0], (loff_t)CONFIG_SYS_FMAN_FW_ADDR,
 		       &fw_length, (u_char *)addr);
 	if (rc == -EUCLEAN) {
 		printf("NAND read of FMAN firmware at offset 0x%x failed %d\n",
-			CONFIG_SYS_QE_FMAN_FW_ADDR, rc);
+			CONFIG_SYS_FMAN_FW_ADDR, rc);
 	}
 #elif defined(CONFIG_SYS_QE_FW_IN_SPIFLASH)
 	struct spi_flash *ucode_flash;
@@ -371,7 +371,7 @@ int fm_init_common(int index, struct ccsr_fman *reg)
 	if (!ucode_flash)
 		printf("SF: probe for ucode failed\n");
 	else {
-		ret = spi_flash_read(ucode_flash, CONFIG_SYS_QE_FMAN_FW_ADDR,
+		ret = spi_flash_read(ucode_flash, CONFIG_SYS_FMAN_FW_ADDR,
 				CONFIG_SYS_QE_FMAN_FW_LENGTH, addr);
 		if (ret)
 			printf("SF: read for ucode failed\n");
@@ -381,7 +381,7 @@ int fm_init_common(int index, struct ccsr_fman *reg)
 	int dev = CONFIG_SYS_MMC_ENV_DEV;
 	void *addr = malloc(CONFIG_SYS_QE_FMAN_FW_LENGTH);
 	u32 cnt = CONFIG_SYS_QE_FMAN_FW_LENGTH / 512;
-	u32 blk = CONFIG_SYS_QE_FMAN_FW_ADDR / 512;
+	u32 blk = CONFIG_SYS_FMAN_FW_ADDR / 512;
 	struct mmc *mmc = find_mmc_device(CONFIG_SYS_MMC_ENV_DEV);
 
 	if (!mmc)
@@ -395,7 +395,7 @@ int fm_init_common(int index, struct ccsr_fman *reg)
 		flush_cache((ulong)addr, cnt * 512);
 	}
 #elif defined(CONFIG_SYS_QE_FMAN_FW_IN_REMOTE)
-	void *addr = (void *)CONFIG_SYS_QE_FMAN_FW_ADDR;
+	void *addr = (void *)CONFIG_SYS_FMAN_FW_ADDR;
 #else
 	void *addr = NULL;
 #endif

drivers/qe/qe.c

@@ -165,7 +165,7 @@ void qe_init(uint qe_base)
 	/*
 	 * Upload microcode to IRAM for those SOCs which do not have ROM in QE.
 	 */
-	qe_upload_firmware((const void *)CONFIG_SYS_QE_FMAN_FW_ADDR);
+	qe_upload_firmware((const void *)CONFIG_SYS_QE_FW_ADDR);
 
 	/* enable the microcode in IRAM */
 	out_be32(&qe_immr->iram.iready,QE_IRAM_READY);

include/configs/B4860QDS.h

@@ -596,7 +596,7 @@ unsigned long get_board_ddr_clk(void);
  * env, so we got 0x110000.
  */
 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
+#define CONFIG_SYS_FMAN_FW_ADDR	0x110000
 #elif defined(CONFIG_SDCARD)
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
@@ -604,10 +604,10 @@ unsigned long get_board_ddr_clk(void);
  * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1130)
+#define CONFIG_SYS_FMAN_FW_ADDR	(512 * 1130)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(8 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_FMAN_FW_ADDR	(8 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 /*
  * Slave has no ucode locally, it can fetch this from remote. When implementing
@@ -617,10 +617,10 @@ unsigned long get_board_ddr_clk(void);
  * master LAW->the ucode address in master's memory space.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xFFE00000
+#define CONFIG_SYS_FMAN_FW_ADDR	0xFFE00000
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR		0xEFF00000
+#define CONFIG_SYS_FMAN_FW_ADDR		0xEFF00000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)

include/configs/MPC8569MDS.h

@@ -493,7 +493,7 @@ extern unsigned long get_clock_freq(void);
 
 /* QE microcode/firmware address */
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xfff00000
+#define CONFIG_SYS_QE_FW_ADDR	0xfff00000
 
 /*
  * BOOTP options

include/configs/P1023RDB.h

@@ -360,7 +360,7 @@ extern unsigned long get_clock_freq(void);
 /* Default address of microcode for the Linux Fman driver */
 /* QE microcode/firmware address */
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xEFF00000
+#define CONFIG_SYS_FMAN_FW_ADDR	0xEFF00000
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 

include/configs/P1023RDS.h

@@ -500,10 +500,10 @@ extern unsigned long get_clock_freq(void);
 /* Default address of microcode for the Linux Fman driver */
 /* QE microcode/firmware address */
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xEFF00000
+#define CONFIG_SYS_FMAN_FW_ADDR	0xEFF00000
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x1f00000
+#define CONFIG_SYS_FMAN_FW_ADDR	0x1f00000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)

include/configs/P2041RDB.h

@@ -506,7 +506,7 @@ unsigned long get_board_sys_clk(unsigned long dummy);
  * env, so we got 0x110000.
  */
 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
+#define CONFIG_SYS_FMAN_FW_ADDR	0x110000
 #elif defined(CONFIG_SDCARD)
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
@@ -514,10 +514,10 @@ unsigned long get_board_sys_clk(unsigned long dummy);
  * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1680)
+#define CONFIG_SYS_FMAN_FW_ADDR	(512 * 1680)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(8 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_FMAN_FW_ADDR	(8 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 /*
  * Slave has no ucode locally, it can fetch this from remote. When implementing
@@ -527,10 +527,10 @@ unsigned long get_board_sys_clk(unsigned long dummy);
  * master LAW->the ucode address in master's memory space.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xFFE00000
+#define CONFIG_SYS_FMAN_FW_ADDR	0xFFE00000
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xEFF00000
+#define CONFIG_SYS_FMAN_FW_ADDR	0xEFF00000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)

include/configs/T1040QDS.h

@@ -602,7 +602,7 @@ unsigned long get_board_ddr_clk(void);
  * env, so we got 0x110000.
  */
 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
+#define CONFIG_SYS_FMAN_FW_ADDR	0x110000
 #elif defined(CONFIG_SDCARD)
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
@@ -610,13 +610,13 @@ unsigned long get_board_ddr_clk(void);
  * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1680)
+#define CONFIG_SYS_FMAN_FW_ADDR	(512 * 1680)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(8 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_FMAN_FW_ADDR	(8 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR		0xEFF00000
+#define CONFIG_SYS_FMAN_FW_ADDR		0xEFF00000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)

include/configs/T1040RDB.h

@@ -517,7 +517,7 @@
  * env, so we got 0x110000.
  */
 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
+#define CONFIG_SYS_FMAN_FW_ADDR	0x110000
 #elif defined(CONFIG_SDCARD)
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
@@ -525,13 +525,13 @@
  * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1680)
+#define CONFIG_SYS_FMAN_FW_ADDR	(512 * 1680)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(4 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_FMAN_FW_ADDR	(4 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR		0xEFF00000
+#define CONFIG_SYS_FMAN_FW_ADDR		0xEFF00000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)

include/configs/T1042RDB_PI.h

@@ -525,7 +525,7 @@
  * env, so we got 0x110000.
  */
 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
+#define CONFIG_SYS_FMAN_FW_ADDR	0x110000
 #elif defined(CONFIG_SDCARD)
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
@@ -533,13 +533,13 @@
  * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1680)
+#define CONFIG_SYS_FMAN_FW_ADDR	(512 * 1680)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(4 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_FMAN_FW_ADDR	(4 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR		0xEFF00000
+#define CONFIG_SYS_FMAN_FW_ADDR		0xEFF00000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)

include/configs/T208xQDS.h

@@ -552,7 +552,7 @@ unsigned long get_board_ddr_clk(void);
  * env, so we got 0x110000.
  */
 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
+#define CONFIG_SYS_FMAN_FW_ADDR	0x110000
 #elif defined(CONFIG_SDCARD)
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
@@ -560,10 +560,10 @@ unsigned long get_board_ddr_clk(void);
  * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1680)
+#define CONFIG_SYS_FMAN_FW_ADDR	(512 * 1680)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(8 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_FMAN_FW_ADDR	(8 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 /*
  * Slave has no ucode locally, it can fetch this from remote. When implementing
@@ -573,10 +573,10 @@ unsigned long get_board_ddr_clk(void);
  * master LAW->the ucode address in master's memory space.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xFFE00000
+#define CONFIG_SYS_FMAN_FW_ADDR	0xFFE00000
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xEFF00000
+#define CONFIG_SYS_FMAN_FW_ADDR	0xEFF00000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)

include/configs/T208xRDB.h

@@ -510,7 +510,7 @@ unsigned long get_board_ddr_clk(void);
  * env, so we got 0x110000.
  */
 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
+#define CONFIG_SYS_FMAN_FW_ADDR	0x110000
 #define CONFIG_CORTINA_FW_ADDR		0x120000
 
 #elif defined(CONFIG_SDCARD)
@@ -520,12 +520,12 @@ unsigned long get_board_ddr_clk(void);
  * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1680)
+#define CONFIG_SYS_FMAN_FW_ADDR	(512 * 1680)
 #define CONFIG_CORTINA_FW_ADDR		(512 * 1808)
 
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(6 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_FMAN_FW_ADDR	(6 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #define CONFIG_CORTINA_FW_ADDR		(7 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 /*
@@ -536,11 +536,11 @@ unsigned long get_board_ddr_clk(void);
  * master LAW->the ucode address in master's memory space.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xFFE00000
+#define CONFIG_SYS_FMAN_FW_ADDR	0xFFE00000
 #define CONFIG_CORTINA_FW_ADDR		0xFFE10000
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xEFF00000
+#define CONFIG_SYS_FMAN_FW_ADDR	0xEFF00000
 #define CONFIG_CORTINA_FW_ADDR		0xEFE00000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000

include/configs/T4240EMU.h

@@ -98,7 +98,7 @@
 #define CONFIG_SYS_INTERLAKEN
 
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR		0xEFF00000
+#define CONFIG_SYS_FMAN_FW_ADDR		0xEFF00000
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 

include/configs/T4240QDS.h

@@ -375,7 +375,7 @@ unsigned long get_board_ddr_clk(void);
  * env, so we got 0x110000.
  */
 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
+#define CONFIG_SYS_FMAN_FW_ADDR	0x110000
 #elif defined(CONFIG_SDCARD)
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
@@ -383,10 +383,10 @@ unsigned long get_board_ddr_clk(void);
  * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1680)
+#define CONFIG_SYS_FMAN_FW_ADDR	(512 * 1680)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(8 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_FMAN_FW_ADDR	(8 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 /*
  * Slave has no ucode locally, it can fetch this from remote. When implementing
@@ -396,10 +396,10 @@ unsigned long get_board_ddr_clk(void);
  * master LAW->the ucode address in master's memory space.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xFFE00000
+#define CONFIG_SYS_FMAN_FW_ADDR	0xFFE00000
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR		0xEFF00000
+#define CONFIG_SYS_FMAN_FW_ADDR		0xEFF00000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)

include/configs/corenet_ds.h

@@ -509,7 +509,7 @@
  * env, so we got 0x110000.
  */
 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
+#define CONFIG_SYS_FMAN_FW_ADDR	0x110000
 #elif defined(CONFIG_SDCARD)
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
@@ -517,10 +517,10 @@
  * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1680)
+#define CONFIG_SYS_FMAN_FW_ADDR	(512 * 1680)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(8 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_FMAN_FW_ADDR	(8 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 /*
  * Slave has no ucode locally, it can fetch this from remote. When implementing
@@ -530,10 +530,10 @@
  * master LAW->the ucode address in master's memory space.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xFFE00000
+#define CONFIG_SYS_FMAN_FW_ADDR	0xFFE00000
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR		0xEFF00000
+#define CONFIG_SYS_FMAN_FW_ADDR		0xEFF00000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)

include/configs/km/km8309-common.h

@@ -27,7 +27,7 @@
 /* QE microcode/firmware address */
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 /* at end of uboot partition, before env */
-#define CONFIG_SYS_QE_FMAN_FW_ADDR   0xF00B0000
+#define CONFIG_SYS_QE_FW_ADDR   0xF00B0000
 
 /*
  * System IO Config

include/configs/km/kmp204x-common.h

@@ -350,7 +350,7 @@ int get_scl(void);
  * ucode is stored after env, so we got 0x120000.
  */
 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x120000
+#define CONFIG_SYS_FMAN_FW_ADDR	0x120000
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 

include/configs/p1_p2_rdb_pc.h

@@ -772,7 +772,7 @@
 #ifdef CONFIG_QE
 /* QE microcode/firmware address */
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xefec0000
+#define CONFIG_SYS_QE_FW_ADDR	0xefec0000
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #endif /* CONFIG_QE */
 

include/configs/p1_twr.h

@@ -348,7 +348,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #ifdef CONFIG_QE
 /* QE microcode/firmware address */
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xefec0000
+#define CONFIG_SYS_QE_FW_ADDR	0xefec0000
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #endif /* CONFIG_QE */