MIPS: Add support for Microchip PIC32MZ[DA] SoC family.

Add Microchip PIC32MZ[DA] SoC family support.

Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>

arch/mips/dts/pic32mzda.dtsi

@@ -0,0 +1,153 @@
+/*
+ * Copyright 2015 Microchip Technology, Inc.
+ * Purna Chandra Mandal, <purna.mandal@microchip.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/clock/microchip,clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "skeleton.dtsi"
+
+/ {
+	compatible = "microchip,pic32mzda", "microchip,pic32mz";
+
+	aliases {
+		gpio0 = &gpioA;
+		gpio1 = &gpioB;
+		gpio2 = &gpioC;
+		gpio3 = &gpioD;
+		gpio4 = &gpioE;
+		gpio5 = &gpioF;
+		gpio6 = &gpioG;
+		gpio7 = &gpioH;
+		gpio8 = &gpioJ;
+		gpio9 = &gpioK;
+	};
+
+	cpus {
+		cpu@0 {
+			compatible = "mips,mips14kc";
+		};
+	};
+
+	clock: clk@1f801200 {
+		compatible = "microchip,pic32mzda-clk";
+		reg = <0x1f801200 0x1000>;
+		#clock-cells = <1>;
+	};
+
+	uart1: serial@1f822000 {
+		compatible = "microchip,pic32mzda-uart";
+		reg = <0x1f822000 0x50>;
+		interrupts = <112 IRQ_TYPE_LEVEL_HIGH>;
+		status = "disabled";
+		clocks = <&clock PB2CLK>;
+	};
+
+	uart2: serial@1f822200 {
+		compatible = "microchip,pic32mzda-uart";
+		reg = <0x1f822200 0x50>;
+		interrupts = <145 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clock PB2CLK>;
+		status = "disabled";
+	};
+
+	uart6: serial@1f822a00 {
+		compatible = "microchip,pic32mzda-uart";
+		reg = <0x1f822a00 0x50>;
+		interrupts = <188 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clock PB2CLK>;
+		status = "disabled";
+	};
+
+	evic: interrupt-controller@1f810000 {
+		compatible = "microchip,pic32mzda-evic";
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		reg = <0x1f810000 0x1000>;
+	};
+
+	pinctrl: pinctrl@1f801400 {
+		compatible = "microchip,pic32mzda-pinctrl";
+		reg = <0x1f801400 0x100>, /* in  */
+		      <0x1f801500 0x200>, /* out */
+		      <0x1f860000 0xa00>; /* port */
+		reg-names = "ppsin","ppsout","port";
+		status = "disabled";
+
+		ranges = <0 0x1f860000 0xa00>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		gpioA: gpio0@0 {
+			compatible = "microchip,pic32mzda-gpio";
+			reg = <0x000 0x48>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpioB: gpio1@100 {
+			compatible = "microchip,pic32mzda-gpio";
+			reg = <0x100 0x48>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpioC: gpio2@200 {
+			compatible = "microchip,pic32mzda-gpio";
+			reg = <0x200 0x48>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpioD: gpio3@300 {
+			compatible = "microchip,pic32mzda-gpio";
+			reg = <0x300 0x48>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpioE: gpio4@400 {
+			compatible = "microchip,pic32mzda-gpio";
+			reg = <0x400 0x48>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpioF: gpio5@500 {
+			compatible = "microchip,pic32mzda-gpio";
+			reg = <0x500 0x48>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpioG: gpio6@600 {
+			compatible = "microchip,pic32mzda-gpio";
+			reg = <0x600 0x48>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpioH: gpio7@700 {
+			compatible = "microchip,pic32mzda-gpio";
+			reg = <0x700 0x48>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpioJ: gpio8@800 {
+			compatible = "microchip,pic32mzda-gpio";
+			reg = <0x800 0x48>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpioK: gpio9@900 {
+			compatible = "microchip,pic32mzda-gpio";
+			reg = <0x900 0x48>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+	};
+};

arch/mips/mach-pic32/Kconfig

@@ -2,6 +2,21 @@ menu "Microchip PIC32 platforms"
 	depends on MACH_PIC32
 
 config SYS_SOC
-	default "none"
+	default "pic32mzda" if SOC_PIC32MZDA
+
+choice
+	prompt "PIC32 SoC select"
+
+config SOC_PIC32MZDA
+	bool "Microchip PIC32MZ[DA] family"
+	select SUPPORTS_LITTLE_ENDIAN
+	select SUPPORTS_CPU_MIPS32_R1
+	select SUPPORTS_CPU_MIPS32_R2
+	select MIPS_L1_CACHE_SHIFT_4
+	select SYS_MIPS_CACHE_INIT_RAM_LOAD
+	help
+	  This supports Microchip PIC32MZ[DA] family of microcontrollers.
+
+endchoice
 
 endmenu

arch/mips/mach-pic32/Makefile

@@ -4,4 +4,4 @@
 # SPDX-License-Identifier:      GPL-2.0+
 #
 
-obj-y = cpu.o
+obj-y = cpu.o lowlevel_init.o reset.o

arch/mips/mach-pic32/cpu.c

@@ -6,8 +6,151 @@
  *
  */
 #include <common.h>
+#include <clk.h>
+#include <dm.h>
+#include <mach/pic32.h>
+#include <mach/ddr.h>
+#include <dt-bindings/clock/microchip,clock.h>
 
+/* Flash prefetch */
+#define PRECON          0x00
+
+/* Flash ECCCON */
+#define ECC_MASK	0x03
+#define ECC_SHIFT	4
+
+#define CLK_MHZ(x)	((x) / 1000000)
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static ulong clk_get_cpu_rate(void)
+{
+	int ret;
+	struct udevice *dev;
+
+	ret = uclass_get_device(UCLASS_CLK, 0, &dev);
+	if (ret) {
+		panic("uclass-clk: device not found\n");
+		return 0;
+	}
+
+	return clk_get_rate(dev);
+}
+
+/* initialize prefetch module related to cpu_clk */
+static void prefetch_init(void)
+{
+	struct pic32_reg_atomic *regs;
+	const void __iomem *base;
+	int v, nr_waits;
+	ulong rate;
+
+	/* cpu frequency in MHZ */
+	rate = clk_get_cpu_rate() / 1000000;
+
+	/* get flash ECC type */
+	base = pic32_get_syscfg_base();
+	v = (readl(base + CFGCON) >> ECC_SHIFT) & ECC_MASK;
+
+	if (v < 2) {
+		if (rate < 66)
+			nr_waits = 0;
+		else if (rate < 133)
+			nr_waits = 1;
+		else
+			nr_waits = 2;
+	} else {
+		if (rate <= 83)
+			nr_waits = 0;
+		else if (rate <= 166)
+			nr_waits = 1;
+		else
+			nr_waits = 2;
+	}
+
+	regs = ioremap(PREFETCH_BASE + PRECON, sizeof(*regs));
+	writel(nr_waits, &regs->raw);
+
+	/* Enable prefetch for all */
+	writel(0x30, &regs->set);
+	iounmap(regs);
+}
+
+/* arch specific CPU init after DM */
+int arch_cpu_init_dm(void)
+{
+	/* flash prefetch */
+	prefetch_init();
+	return 0;
+}
+
+/* Un-gate DDR2 modules (gated by default) */
+static void ddr2_pmd_ungate(void)
+{
+	void __iomem *regs;
+
+	regs = pic32_get_syscfg_base();
+	writel(0, regs + PMD7);
+}
+
+/* initialize the DDR2 Controller and DDR2 PHY */
 phys_size_t initdram(int board_type)
 {
+	ddr2_pmd_ungate();
+	ddr2_phy_init();
+	ddr2_ctrl_init();
+	return ddr2_calculate_size();
+}
+
+int misc_init_r(void)
+{
+	set_io_port_base(0);
+	return 0;
+}
+
+#ifdef CONFIG_DISPLAY_BOARDINFO
+const char *get_core_name(void)
+{
+	u32 proc_id;
+	const char *str;
+
+	proc_id = read_c0_prid();
+	switch (proc_id) {
+	case 0x19e28:
+		str = "PIC32MZ[DA]";
+		break;
+	default:
+		str = "UNKNOWN";
+	}
+
+	return str;
+}
+#endif
+#ifdef CONFIG_CMD_CLK
+int soc_clk_dump(void)
+{
+	int i, ret;
+	struct udevice *dev;
+
+	ret = uclass_get_device(UCLASS_CLK, 0, &dev);
+	if (ret) {
+		printf("clk-uclass not found\n");
+		return ret;
+	}
+
+	printf("PLL Speed: %lu MHz\n",
+	       CLK_MHZ(clk_get_periph_rate(dev, PLLCLK)));
+	printf("CPU Speed: %lu MHz\n", CLK_MHZ(clk_get_rate(dev)));
+	printf("MPLL Speed: %lu MHz\n",
+	       CLK_MHZ(clk_get_periph_rate(dev, MPLL)));
+
+	for (i = PB1CLK; i <= PB7CLK; i++)
+		printf("PB%d Clock Speed: %lu MHz\n", i - PB1CLK + 1,
+		       CLK_MHZ(clk_get_periph_rate(dev, i)));
+
+	for (i = REF1CLK; i <= REF5CLK; i++)
+		printf("REFO%d Clock Speed: %lu MHz\n", i - REF1CLK + 1,
+		       CLK_MHZ(clk_get_periph_rate(dev, i)));
 	return 0;
 }
+#endif

arch/mips/mach-pic32/include/mach/pic32.h

@@ -73,4 +73,7 @@ static inline void __iomem *pic32_get_syscfg_base(void)
 	return (void __iomem *)CKSEG1ADDR(PIC32_CFG_BASE);
 }
 
+/* Core */
+const char *get_core_name(void);
+
 #endif	/* __PIC32_REGS_H__ */

arch/mips/mach-pic32/lowlevel_init.S

@@ -0,0 +1,27 @@
+/*
+ * (c) 2015 Purna Chandra Mandal <purna.mandal@microchip.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+*/
+
+#include <config.h>
+#include <asm/regdef.h>
+#include <asm/mipsregs.h>
+#include <asm/asm.h>
+
+LEAF(lowlevel_init)
+	/*
+	 * Establish Cause
+	 * (set IV bit)
+	 */
+	li	t1, 0x00800000
+	mtc0	t1, CP0_CAUSE
+
+	/* Establish Wired (and Random) */
+	mtc0	zero, CP0_WIRED
+	 nop
+
+	jr	ra
+	 nop
+	END(lowlevel_init)

arch/mips/mach-pic32/reset.c

@@ -0,0 +1,36 @@
+/*
+ * (c) 2015 Purna Chandra Mandal <purna.mandal@microchip.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <mach/pic32.h>
+
+/* SYSKEY */
+#define UNLOCK_KEY1	0xaa996655
+#define UNLOCK_KEY2	0x556699aa
+#define LOCK_KEY	0
+
+#define RSWRST          0x1250
+
+void _machine_restart(void)
+{
+	void __iomem *base;
+
+	base = pic32_get_syscfg_base();
+
+	/* unlock sequence */
+	writel(LOCK_KEY, base + SYSKEY);
+	writel(UNLOCK_KEY1, base + SYSKEY);
+	writel(UNLOCK_KEY2, base + SYSKEY);
+
+	/* soft reset */
+	writel(0x1, base + RSWRST);
+	(void) readl(base + RSWRST);
+
+	while (1)
+		;
+}