configs: ls1012a: add pfe configuration for LS1012A

Add configurations for PFE.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

configs/ls1012a2g5rdb_qspi_defconfig

@@ -31,7 +31,9 @@ CONFIG_DM=y
 CONFIG_DM_MMC=y
 CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH=y
+CONFIG_DM_ETH=y
 CONFIG_NETDEVICES=y
+CONFIG_FSL_PFE=y
 CONFIG_SYS_NS16550=y
 CONFIG_DM_SPI=y
 CONFIG_USB=y

configs/ls1012afrdm_qspi_defconfig

@@ -29,8 +29,10 @@ CONFIG_DM=y
 # CONFIG_MMC is not set
 CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH=y
+CONFIG_DM_ETH=y
 CONFIG_NETDEVICES=y
 CONFIG_E1000=y
+CONFIG_FSL_PFE=y
 CONFIG_PCI=y
 CONFIG_DM_PCI=y
 CONFIG_DM_PCI_COMPAT=y

configs/ls1012aqds_qspi_defconfig

@@ -36,8 +36,10 @@ CONFIG_SCSI_AHCI=y
 CONFIG_DM_MMC=y
 CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH=y
+CONFIG_DM_ETH=y
 CONFIG_NETDEVICES=y
 CONFIG_E1000=y
+CONFIG_FSL_PFE=y
 CONFIG_PCI=y
 CONFIG_DM_PCI=y
 CONFIG_DM_PCI_COMPAT=y

configs/ls1012ardb_qspi_defconfig

@@ -32,8 +32,10 @@ CONFIG_DM=y
 CONFIG_DM_MMC=y
 CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH=y
+CONFIG_DM_ETH=y
 CONFIG_NETDEVICES=y
 CONFIG_E1000=y
+CONFIG_FSL_PFE=y
 CONFIG_PCI=y
 CONFIG_DM_PCI=y
 CONFIG_DM_PCI_COMPAT=y

drivers/net/Kconfig

@@ -1,4 +1,5 @@
 source "drivers/net/phy/Kconfig"
+source "drivers/net/pfe_eth/Kconfig"
 
 config DM_ETH
 	bool "Enable Driver Model for Ethernet drivers"

drivers/net/Makefile

@@ -73,3 +73,4 @@ obj-$(CONFIG_FSL_MEMAC) += fm/memac_phy.o
 obj-$(CONFIG_VSC9953) += vsc9953.o
 obj-$(CONFIG_PIC32_ETH) += pic32_mdio.o pic32_eth.o
 obj-$(CONFIG_DWC_ETH_QOS) += dwc_eth_qos.o
+obj-$(CONFIG_FSL_PFE) += pfe_eth/

drivers/net/pfe_eth/Kconfig

@@ -0,0 +1,12 @@
+menuconfig FSL_PFE
+	bool "NXP PFE Ethernet driver"
+	help
+	  This driver provides support for NXP's Packet Forwarding Engine.
+
+if FSL_PFE
+
+config SYS_FSL_PFE_ADDR
+	hex "PFE base address"
+	default 0x04000000
+
+endif

drivers/net/pfe_eth/Makefile

@@ -0,0 +1,12 @@
+# Copyright 2015-2016 Freescale Semiconductor, Inc.
+# Copyright 2017 NXP
+#
+# SPDX-License-Identifier:GPL-2.0+
+
+# Layerscape PFE driver
+obj-y += pfe_cmd.o	\
+	 pfe_driver.o	\
+	 pfe_eth.o	\
+	 pfe_firmware.o \
+	 pfe_hw.o	\
+	 pfe_mdio.o

include/configs/ls1012a2g5rdb.h

@@ -9,15 +9,6 @@
 
 #include "ls1012a_common.h"
 
-/* PFE Ethernet */
-#ifdef CONFIG_FSL_PFE
-#define EMAC1_PHY_ADDR          0x2
-#define EMAC2_PHY_ADDR          0x1
-#define CONFIG_PHYLIB
-#define CONFIG_PHYLIB_10G
-#define CONFIG_PHY_AQUANTIA
-#endif
-
 /* DDR */
 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
 #define CONFIG_CHIP_SELECTS_PER_CTRL	1
@@ -110,7 +101,7 @@
 
 #undef CONFIG_BOOTCOMMAND
 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
-#define CONFIG_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd; " \
+#define CONFIG_BOOTCOMMAND "pfe stop;run distro_bootcmd; run qspi_bootcmd; " \
 			   "env exists secureboot && esbc_halt;"
 #endif
 

include/configs/ls1012a_common.h

@@ -112,9 +112,9 @@
 	"kernel_size=0x2800000\0"		\
 
 #undef CONFIG_BOOTCOMMAND
-#define CONFIG_BOOTCOMMAND		"sf probe 0:0; sf read $kernel_load "\
-					"$kernel_start $kernel_size && "\
-					"bootm $kernel_load"
+#define CONFIG_BOOTCOMMAND	"pfe stop; sf probe 0:0; sf read $kernel_load "\
+				"$kernel_start $kernel_size && "\
+				"bootm $kernel_load"
 
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */

include/configs/ls1012afrdm.h

@@ -68,7 +68,7 @@
 		"$kernel_addr $kernel_size && bootm $load_addr#$board\0"
 
 #undef CONFIG_BOOTCOMMAND
-#define CONFIG_BOOTCOMMAND "run distro_bootcmd;run qspi_bootcmd"
+#define CONFIG_BOOTCOMMAND "pfe stop;run distro_bootcmd;run qspi_bootcmd"
 
 #define CONFIG_CMD_MEMINFO
 #define CONFIG_CMD_MEMTEST

include/configs/ls1012ardb.h

@@ -117,7 +117,7 @@
 		"bootm $load_addr#$board\0"
 
 #undef CONFIG_BOOTCOMMAND
-#define CONFIG_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd; "	\
+#define CONFIG_BOOTCOMMAND "pfe stop; run distro_bootcmd; run qspi_bootcmd; "\
 			   "env exists secureboot && esbc_halt;"
 
 #include <asm/fsl_secure_boot.h>