Merge branch 'master' of git://www.denx.de/git/u-boot-imx

arch/arm/cpu/armv7/mx6/soc.c

@@ -21,7 +21,6 @@
 #include <stdbool.h>
 #include <asm/arch/mxc_hdmi.h>
 #include <asm/arch/crm_regs.h>
-#include <asm/bootm.h>
 #include <dm.h>
 #include <imx_thermal.h>
 
@@ -289,6 +288,22 @@ static void set_preclk_from_osc(void)
 }
 #endif
 
+#define SRC_SCR_WARM_RESET_ENABLE	0
+
+static void init_src(void)
+{
+	struct src *src_regs = (struct src *)SRC_BASE_ADDR;
+	u32 val;
+
+	/*
+	 * force warm reset sources to generate cold reset
+	 * for a more reliable restart
+	 */
+	val = readl(&src_regs->scr);
+	val &= ~(1 << SRC_SCR_WARM_RESET_ENABLE);
+	writel(val, &src_regs->scr);
+}
+
 int arch_cpu_init(void)
 {
 	init_aips();
@@ -323,6 +338,8 @@ int arch_cpu_init(void)
 	mxs_dma_init();
 #endif
 
+	init_src();
+
 	return 0;
 }
 

board/warp/README

@@ -0,0 +1,56 @@
+How to Update U-boot on Warp board
+----------------------------------
+
+Required software on the host PC:
+
+- imx_usb_loader: https://github.com/boundarydevices/imx_usb_loader
+
+- dfu-util: http://dfu-util.sourceforge.net/releases/
+
+Build U-boot for Warp:
+
+$ make mrproper
+$ make warp_config
+$ make
+
+This will generate the U-boot binary called u-boot.imx.
+
+Put warp board in USB download mode
+
+Connect a USB to serial adapter between the host PC and warp
+
+Connect a USB cable between the OTG warp port and the host PC
+
+Open a terminal program such as minicom
+
+Copy u-boot.imx to the imx_usb_loader folder.
+
+Load u-boot.imx via USB:
+
+$ sudo ./imx_usb u-boot.imx
+
+Then U-boot should start and its messages will appear in the console program.
+
+Use the default environment variables:
+
+=> env default -f -a
+=> save
+
+Run the DFU command:
+=> dfu 0 mmc 0
+
+Transfer u-boot.imx that will be flashed into the eMMC:
+
+$ sudo dfu-util -D u-boot.imx -a boot
+
+Then on the U-boot prompt the following message should be seen after a succesful
+upgrade:
+
+#DOWNLOAD ... OK
+Ctrl+C to exit ...
+
+Remove power from the warp board.
+
+Put warp board into normal boot mode
+
+Power up the board and the new updated U-boot should boot from eMMC

common/board_f.c

@@ -111,7 +111,8 @@ static int init_func_watchdog_init(void)
 {
 # if defined(CONFIG_HW_WATCHDOG) && (defined(CONFIG_BLACKFIN) || \
 	defined(CONFIG_M68K) || defined(CONFIG_MICROBLAZE) || \
-	defined(CONFIG_SH) || defined(CONFIG_AT91SAM9_WATCHDOG))
+	defined(CONFIG_SH) || defined(CONFIG_AT91SAM9_WATCHDOG) || \
+	defined(CONFIG_IMX_WATCHDOG))
 	hw_watchdog_init();
 # endif
 	puts("       Watchdog enabled\n");

include/configs/hummingboard.h

@@ -185,9 +185,6 @@
 #define CONFIG_SYS_HUSH_PARSER
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_SYS_CBSIZE		1024
-
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_MAXARGS	       16
 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
 

include/configs/mx25pdk.h

@@ -229,8 +229,6 @@
 #define CONFIG_SYS_HUSH_PARSER
 #define CONFIG_AUTO_COMPLETE
 
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_MAXARGS	       16
 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
 

include/configs/mx31pdk.h

@@ -121,9 +121,6 @@
  */
 #define CONFIG_SYS_LONGHELP	/* undef to save memory */
 #define CONFIG_SYS_CBSIZE	256	/* Console I/O Buffer Size */
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE + \
-				sizeof(CONFIG_SYS_PROMPT)+16)
 /* max number of command args */
 #define CONFIG_SYS_MAXARGS	16
 /* Boot Argument Buffer Size */

include/configs/mx35pdk.h

@@ -139,8 +139,6 @@
 
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_SYS_CBSIZE	256	/* Console I/O Buffer Size */
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_MAXARGS	16	/* max number of command args */
 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
 

include/configs/mx51evk.h

@@ -222,8 +222,6 @@
 #define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser */
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_MAXARGS	16	/* max number of command args */
 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
 

include/configs/mx53ard.h

@@ -186,7 +186,6 @@
 /* Miscellaneous configurable options */
 #define CONFIG_SYS_LONGHELP		/* undef to save memory */
 #define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser */
-#define CONFIG_SYS_PROMPT		"MX53ARD U-Boot > "
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
 

include/configs/mx53loco.h

@@ -184,8 +184,6 @@
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
 
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_MAXARGS	16	/* max number of command args */
 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
 

include/configs/mx6_common.h

@@ -28,8 +28,6 @@
 #define CONFIG_SYS_PL310_BASE	L2_PL310_BASE
 #endif
 
-#define CONFIG_SYS_FSL_ESDHC_HAS_DDR_MODE
-
 #define CONFIG_MP
 #define CONFIG_MXC_GPT_HCLK
 

include/configs/mx6qarm2.h

@@ -153,8 +153,6 @@
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_SYS_CBSIZE		256
 
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_MAXARGS		16
 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
 

include/configs/mx6sabre_common.h

@@ -111,12 +111,10 @@
 			"setenv get_cmd tftp; " \
 		"fi; " \
 		"if ${get_cmd} ${update_sd_firmware_filename}; then " \
-			"if mmc dev ${emmcdev} && " \
-				"mmc open ${emmcdev} 1; then "	\
+			"if mmc dev ${emmcdev} 1; then "	\
 				"setexpr fw_sz ${filesize} / 0x200; " \
 				"setexpr fw_sz ${fw_sz} + 1; "	\
 				"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
-				"mmc close ${emmcdev} 1; " \
 			"fi; "	\
 		"fi\0"
 #else
@@ -278,6 +276,7 @@
 #define CONFIG_IMX_HDMI
 #define CONFIG_IMX_VIDEO_SKIP
 
+#ifndef CONFIG_SPL
 #define CONFIG_CI_UDC
 #define CONFIG_USBD_HS
 #define CONFIG_USB_GADGET_DUALSPEED
@@ -291,5 +290,6 @@
 #define CONFIG_G_DNL_VENDOR_NUM		0x0525
 #define CONFIG_G_DNL_PRODUCT_NUM	0xa4a5
 #define CONFIG_G_DNL_MANUFACTURER	"FSL"
+#endif
 
 #endif                         /* __MX6QSABRE_COMMON_CONFIG_H */

include/configs/mx6slevk.h

@@ -169,8 +169,6 @@
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_SYS_CBSIZE		256
 
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_MAXARGS		16
 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
 

include/configs/mx6sxsabresd.h

@@ -134,8 +134,6 @@
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_SYS_CBSIZE		1024
 
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_MAXARGS		256
 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
 

include/configs/mxs.h

@@ -94,9 +94,6 @@
 /* U-Boot general configuration */
 #define CONFIG_SYS_LONGHELP
 #define CONFIG_SYS_CBSIZE	1024		/* Console I/O buffer size */
-#define CONFIG_SYS_PBSIZE	\
-	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-						/* Print buffer size */
 #define CONFIG_SYS_MAXARGS	32		/* Max number of command args */
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
 						/* Boot argument buffer size */

include/configs/nitrogen6x.h

@@ -325,9 +325,6 @@
 #define CONFIG_SYS_PROMPT	       "U-Boot > "
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_SYS_CBSIZE	       1024
-
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_MAXARGS	       48
 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
 

include/configs/novena.h

@@ -58,9 +58,6 @@
 /* U-Boot general configurations */
 #define CONFIG_SYS_LONGHELP
 #define CONFIG_SYS_CBSIZE	1024		/* Console I/O buffer size */
-#define CONFIG_SYS_PBSIZE	\
-	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-						/* Print buffer size */
 #define CONFIG_SYS_MAXARGS	32		/* Max number of command args */
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
 						/* Boot argument buffer size */

include/configs/wandboard.h

@@ -249,9 +249,6 @@
 #define CONFIG_SYS_HUSH_PARSER
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_SYS_CBSIZE		256
-
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_MAXARGS	       16
 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
 

include/configs/warp.h

@@ -28,7 +28,7 @@
 #define CONFIG_REVISION_TAG
 
 /* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN		(3 * SZ_1M)
+#define CONFIG_SYS_MALLOC_LEN		(35 * SZ_1M) /* Increase due to DFU */
 
 #define CONFIG_BOARD_EARLY_INIT_F
 #define CONFIG_BOARD_LATE_INIT
@@ -42,6 +42,7 @@
 #define CONFIG_FSL_USDHC
 #define CONFIG_SYS_FSL_ESDHC_ADDR	0
 #define CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT
+#define CONFIG_SYS_FSL_ESDHC_HAS_DDR_MODE
 
 #define CONFIG_MMC
 #define CONFIG_CMD_MMC
@@ -81,9 +82,6 @@
 #define CONFIG_HW_WATCHDOG
 #define CONFIG_IMX_WATCHDOG
 #define CONFIG_WATCHDOG_TIMEOUT_MSECS 30000 /* 30s */
-
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_MAXARGS		16
 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
 
@@ -150,6 +148,12 @@
 #define CONFIG_G_DNL_PRODUCT_NUM	0xa4a5
 #define CONFIG_G_DNL_MANUFACTURER	"FSL"
 
+#define CONFIG_CMD_DFU
+#define CONFIG_DFU_FUNCTION
+#define CONFIG_DFU_MMC
+#define CONFIG_SYS_DFU_DATA_BUF_SIZE SZ_32M
+#define DFU_DEFAULT_POLL_TIMEOUT 300
+
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"script=boot.scr\0" \
 	"image=zImage\0" \
@@ -164,6 +168,7 @@
 	"mmcdev=0\0" \
 	"mmcpart=1\0" \
 	"mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
+	"dfu_alt_info=boot raw 0x2 0x400 mmcpart 1\0" \
 	"mmcargs=setenv bootargs console=${console},${baudrate} " \
 		"root=${mmcroot}\0" \
 	"loadbootscript=" \