Merge branch 'microblaze' of git://git.denx.de/u-boot-microblaze

arch/arm/include/asm/u-boot-arm.h

@@ -36,7 +36,6 @@ int	arch_early_init_r(void);
 
 /* board/.../... */
 int	board_init(void);
-int	dram_init (void);
 void	dram_init_banksize (void);
 
 /* cpu/.../interrupt.c */

arch/microblaze/config.mk

@@ -15,3 +15,8 @@ endif
 CONFIG_STANDALONE_LOAD_ADDR ?= 0x80F00000
 
 PLATFORM_CPPFLAGS += -ffixed-r31 -D__microblaze__
+
+ifeq ($(CONFIG_SPL_BUILD),)
+PLATFORM_CPPFLAGS += -fPIC
+endif
+__HAVE_ARCH_GENERIC_BOARD := y

arch/microblaze/cpu/exception.c

@@ -13,49 +13,52 @@ void _hw_exception_handler (void)
 {
 	int address = 0;
 	int state = 0;
+
 	/* loading address of exception EAR */
-	MFS (address, rear);
+	MFS(address, rear);
 	/* loading excetpion state register ESR */
-	MFS (state, resr);
-	printf ("Hardware exception at 0x%x address\n", address);
+	MFS(state, resr);
+	printf("Hardware exception at 0x%x address\n", address);
+	R17(address);
+	printf("Return address from exception 0x%x\n", address);
 	switch (state & 0x1f) {	/* mask on exception cause */
 	case 0x1:
-		puts ("Unaligned data access exception\n");
+		puts("Unaligned data access exception\n");
 		break;
 	case 0x2:
-		puts ("Illegal op-code exception\n");
+		puts("Illegal op-code exception\n");
 		break;
 	case 0x3:
-		puts ("Instruction bus error exception\n");
+		puts("Instruction bus error exception\n");
 		break;
 	case 0x4:
-		puts ("Data bus error exception\n");
+		puts("Data bus error exception\n");
 		break;
 	case 0x5:
-		puts ("Divide by zero exception\n");
+		puts("Divide by zero exception\n");
 		break;
 #ifdef MICROBLAZE_V5
 	case 0x7:
 		puts("Priviledged or stack protection violation exception\n");
 		break;
 	case 0x1000:
-		puts ("Exception in delay slot\n");
+		puts("Exception in delay slot\n");
 		break;
 #endif
 	default:
-		puts ("Undefined cause\n");
+		puts("Undefined cause\n");
 		break;
 	}
-	printf ("Unaligned %sword access\n", ((state & 0x800) ? "" : "half"));
-	printf ("Unaligned %s access\n", ((state & 0x400) ? "store" : "load"));
-	printf ("Register R%x\n", (state & 0x3E) >> 5);
-	hang ();
+	printf("Unaligned %sword access\n", ((state & 0x800) ? "" : "half"));
+	printf("Unaligned %s access\n", ((state & 0x400) ? "store" : "load"));
+	printf("Register R%x\n", (state & 0x3E) >> 5);
+	hang();
 }
 
 #ifdef CONFIG_SYS_USR_EXCEP
 void _exception_handler (void)
 {
-	puts ("User vector_exception\n");
-	hang ();
+	puts("User vector_exception\n");
+	hang();
 }
 #endif

arch/microblaze/cpu/interrupts.c

@@ -14,10 +14,9 @@
 #include <asm/microblaze_intc.h>
 #include <asm/asm.h>
 
-#undef DEBUG_INT
-
 void enable_interrupts(void)
 {
+	debug("Enable interrupts for the whole CPU\n");
 	MSRSET(0x2);
 }
 
@@ -50,12 +49,11 @@ static void enable_one_interrupt(int irq)
 	offset <<= irq;
 	mask = intc->ier;
 	intc->ier = (mask | offset);
-#ifdef DEBUG_INT
-	printf("Enable one interrupt irq %x - mask %x,ier %x\n", offset, mask,
-		intc->ier);
-	printf("INTC isr %x, ier %x, iar %x, mer %x\n", intc->isr, intc->ier,
-		intc->iar, intc->mer);
-#endif
+
+	debug("Enable one interrupt irq %x - mask %x,ier %x\n", offset, mask,
+	      intc->ier);
+	debug("INTC isr %x, ier %x, iar %x, mer %x\n", intc->isr, intc->ier,
+	      intc->iar, intc->mer);
 }
 
 static void disable_one_interrupt(int irq)
@@ -66,12 +64,11 @@ static void disable_one_interrupt(int irq)
 	offset <<= irq;
 	mask = intc->ier;
 	intc->ier = (mask & ~offset);
-#ifdef DEBUG_INT
-	printf("Disable one interrupt irq %x - mask %x,ier %x\n", irq, mask,
-		intc->ier);
-	printf("INTC isr %x, ier %x, iar %x, mer %x\n", intc->isr, intc->ier,
-		intc->iar, intc->mer);
-#endif
+
+	debug("Disable one interrupt irq %x - mask %x,ier %x\n", irq, mask,
+	      intc->ier);
+	debug("INTC isr %x, ier %x, iar %x, mer %x\n", intc->isr, intc->ier,
+	      intc->iar, intc->mer);
 }
 
 int install_interrupt_handler(int irq, interrupt_handler_t *hdlr, void *arg)
@@ -88,12 +85,12 @@ int install_interrupt_handler(int irq, interrupt_handler_t *hdlr, void *arg)
 		act->handler = hdlr;
 		act->arg = arg;
 		act->count = 0;
-		enable_one_interrupt (irq);
+		enable_one_interrupt(irq);
 		return 0;
 	}
 
 	/* Disable */
-	act->handler = (interrupt_handler_t *) def_hdlr;
+	act->handler = (interrupt_handler_t *)def_hdlr;
 	act->arg = (void *)irq;
 	disable_one_interrupt(irq);
 	return 1;
@@ -107,18 +104,17 @@ static void intc_init(void)
 	intc->iar = 0xFFFFFFFF;
 	/* XIntc_Start - hw_interrupt enable and all interrupt enable */
 	intc->mer = 0x3;
-#ifdef DEBUG_INT
-	printf("INTC isr %x, ier %x, iar %x, mer %x\n", intc->isr, intc->ier,
-		intc->iar, intc->mer);
-#endif
+
+	debug("INTC isr %x, ier %x, iar %x, mer %x\n", intc->isr, intc->ier,
+	      intc->iar, intc->mer);
 }
 
-int interrupts_init(void)
+int interrupt_init(void)
 {
 	int i;
 
 #if defined(CONFIG_SYS_INTC_0_ADDR) && defined(CONFIG_SYS_INTC_0_NUM)
-	intc = (microblaze_intc_t *) (CONFIG_SYS_INTC_0_ADDR);
+	intc = (microblaze_intc_t *)CONFIG_SYS_INTC_0_ADDR;
 	irq_no = CONFIG_SYS_INTC_0_NUM;
 #endif
 	if (irq_no) {
@@ -130,7 +126,7 @@ int interrupts_init(void)
 
 		/* initialize irq list */
 		for (i = 0; i < irq_no; i++) {
-			vecs[i].handler = (interrupt_handler_t *) def_hdlr;
+			vecs[i].handler = (interrupt_handler_t *)def_hdlr;
 			vecs[i].arg = (void *)i;
 			vecs[i].count = 0;
 		}
@@ -147,31 +143,29 @@ void interrupt_handler(void)
 {
 	int irqs = intc->ivr;	/* find active interrupt */
 	int mask = 1;
-#ifdef DEBUG_INT
 	int value;
-	printf ("INTC isr %x, ier %x, iar %x, mer %x\n", intc->isr, intc->ier,
-		intc->iar, intc->mer);
-	R14(value);
-	printf ("Interrupt handler on %x line, r14 %x\n", irqs, value);
-#endif
 	struct irq_action *act = vecs + irqs;
 
-#ifdef DEBUG_INT
-	printf
-	    ("Jumping to interrupt handler rutine addr %x,count %x,arg %x\n",
-	     act->handler, act->count, act->arg);
+	debug("INTC isr %x, ier %x, iar %x, mer %x\n", intc->isr, intc->ier,
+	      intc->iar, intc->mer);
+#ifdef DEBUG
+	R14(value);
 #endif
-	act->handler (act->arg);
+	debug("Interrupt handler on %x line, r14 %x\n", irqs, value);
+
+	debug("Jumping to interrupt handler rutine addr %x,count %x,arg %x\n",
+	      (u32)act->handler, act->count, (u32)act->arg);
+	act->handler(act->arg);
 	act->count++;
 
 	intc->iar = mask << irqs;
 
-#ifdef DEBUG_INT
-	printf ("Dump INTC reg, isr %x, ier %x, iar %x, mer %x\n", intc->isr,
-		intc->ier, intc->iar, intc->mer);
+	debug("Dump INTC reg, isr %x, ier %x, iar %x, mer %x\n", intc->isr,
+	      intc->ier, intc->iar, intc->mer);
+#ifdef DEBUG
 	R14(value);
-	printf ("Interrupt handler on %x line, r14 %x\n", irqs, value);
 #endif
+	debug("Interrupt handler on %x line, r14 %x\n", irqs, value);
 }
 
 #if defined(CONFIG_CMD_IRQ)
@@ -186,10 +180,10 @@ int do_irqinfo(cmd_tbl_t *cmdtp, int flag, int argc, const char *argv[])
 		      "-----------------------------\n");
 
 		for (i = 0; i < irq_no; i++) {
-			if (act->handler != (interrupt_handler_t *) def_hdlr) {
+			if (act->handler != (interrupt_handler_t *)def_hdlr) {
 				printf("%02d  %08x  %08x  %d\n", i,
-					(int)act->handler, (int)act->arg,
-								act->count);
+				       (int)act->handler, (int)act->arg,
+				       act->count);
 			}
 			act++;
 		}

arch/microblaze/cpu/irq.S

@@ -11,71 +11,70 @@
 	.text
 	.global _interrupt_handler
 _interrupt_handler:
-	swi	r2, r1, -4
-	swi	r3, r1, -8
-	swi	r4, r1, -12
-	swi	r5, r1, -16
-	swi	r6, r1, -20
-	swi	r7, r1, -24
-	swi	r8, r1, -28
-	swi	r9, r1, -32
-	swi	r10, r1, -36
-	swi	r11, r1, -40
-	swi	r12, r1, -44
-	swi	r13, r1, -48
-	swi	r14, r1, -52
-	swi	r15, r1, -56
-	swi	r16, r1, -60
-	swi	r17, r1, -64
-	swi	r18, r1, -68
-	swi	r19, r1, -72
-	swi	r20, r1, -76
-	swi	r21, r1, -80
-	swi	r22, r1, -84
-	swi	r23, r1, -88
-	swi	r24, r1, -92
-	swi	r25, r1, -96
-	swi	r26, r1, -100
-	swi	r27, r1, -104
-	swi	r28, r1, -108
-	swi	r29, r1, -112
-	swi	r30, r1, -116
-	swi	r31, r1, -120
 	addik	r1, r1, -124
+	swi	r2, r1, 4
+	swi	r3, r1, 8
+	swi	r4, r1, 12
+	swi	r5, r1, 16
+	swi	r6, r1, 20
+	swi	r7, r1, 24
+	swi	r8, r1, 28
+	swi	r9, r1, 32
+	swi	r10, r1, 36
+	swi	r11, r1, 40
+	swi	r12, r1, 44
+	swi	r13, r1, 48
+	swi	r14, r1, 52
+	swi	r15, r1, 56
+	swi	r16, r1, 60
+	swi	r17, r1, 64
+	swi	r18, r1, 68
+	swi	r19, r1, 72
+	swi	r20, r1, 76
+	swi	r21, r1, 80
+	swi	r22, r1, 84
+	swi	r23, r1, 88
+	swi	r24, r1, 92
+	swi	r25, r1, 96
+	swi	r26, r1, 100
+	swi	r27, r1, 104
+	swi	r28, r1, 108
+	swi	r29, r1, 112
+	swi	r30, r1, 116
+	swi	r31, r1, 120
 	brlid	r15, interrupt_handler
 	nop
+	lwi	r31, r1, 120
+	lwi	r30, r1, 116
+	lwi	r29, r1, 112
+	lwi	r28, r1, 108
+	lwi	r27, r1, 104
+	lwi	r26, r1, 100
+	lwi	r25, r1, 96
+	lwi	r24, r1, 92
+	lwi	r23, r1, 88
+	lwi	r22, r1, 84
+	lwi	r21, r1, 80
+	lwi	r20, r1, 76
+	lwi	r19, r1, 72
+	lwi	r18, r1, 68
+	lwi	r17, r1, 64
+	lwi	r16, r1, 60
+	lwi	r15, r1, 56
+	lwi	r14, r1, 52
+	lwi	r13, r1, 48
+	lwi	r12, r1, 44
+	lwi	r11, r1, 40
+	lwi	r10, r1, 36
+	lwi	r9, r1, 32
+	lwi	r8, r1, 28
+	lwi	r7, r1, 24
+	lwi	r6, r1, 20
+	lwi	r5, r1, 16
+	lwi	r4, r1, 12
+	lwi	r3, r1, 8
+	lwi	r2, r1, 4
 	addik	r1, r1, 124
-	lwi	r31, r1, -120
-	lwi	r30, r1, -116
-	lwi	r29, r1, -112
-	lwi	r28, r1, -108
-	lwi	r27, r1, -104
-	lwi	r26, r1, -100
-	lwi	r25, r1, -96
-	lwi	r24, r1, -92
-	lwi	r23, r1, -88
-	lwi	r22, r1, -84
-	lwi	r21, r1, -80
-	lwi	r20, r1, -76
-	lwi	r19, r1, -72
-	lwi	r18, r1, -68
-	lwi	r17, r1, -64
-	lwi	r16, r1, -60
-	lwi	r15, r1, -56
-	lwi	r14, r1, -52
-	lwi	r13, r1, -48
-	lwi	r12, r1, -44
-	lwi	r11, r1, -40
-	lwi	r10, r1, -36
-	lwi	r9, r1, -32
-	lwi	r8, r1, -28
-	lwi	r7, r1, -24
-	lwi	r6, r1, -20
-	lwi	r5, r1, -16
-	lwi	r4, r1, -12
-	lwi	r3, r1, -8
-	lwi	r2, r1, -4
-
 	rtid	r14, 0
 	nop
 	.size _interrupt_handler,.-_interrupt_handler

arch/microblaze/cpu/spl.c

@@ -25,8 +25,6 @@ u32 spl_boot_device(void)
 /* Board initialization after bss clearance */
 void spl_board_init(void)
 {
-	gd = (gd_t *)CONFIG_SPL_STACK_ADDR;
-
 	/* enable console uart printing */
 	preloader_console_init();
 }

arch/microblaze/cpu/start.S

@@ -29,8 +29,12 @@ _start:
 	addi	r1, r0, CONFIG_SPL_STACK_ADDR
 	mts	rshr, r1
 	addi	r1, r1, -4	/* Decrement SP to top of memory */
+#else
+#if defined(CONFIG_SYS_MALLOC_F_LEN)
+	addi	r1, r0, CONFIG_SYS_INIT_SP_OFFSET - CONFIG_SYS_MALLOC_F_LEN
 #else
 	addi	r1, r0, CONFIG_SYS_INIT_SP_OFFSET
+#endif
 	mts	rshr, r1
 	addi	r1, r1, -4	/* Decrement SP to top of memory */
 
@@ -129,7 +133,7 @@ _start:
 	/* Flush cache before enable cache */
 	addik	r5, r0, 0
 	addik	r6, r0, XILINX_DCACHE_BYTE_SIZE
-flush:	bralid r15, flush_cache
+	bralid r15, flush_cache
 	nop
 
 	/* enable instruction and data cache */
@@ -150,12 +154,28 @@ clear_bss:
 	bnei    r6, 2b
 3:	/* jumping to board_init */
 #ifndef CONFIG_SPL_BUILD
+	or	r5, r0, r0	/* flags - empty */
+	addi    r31, r0, _gd
+#if defined(CONFIG_SYS_MALLOC_F_LEN)
+	addi	r6, r0, CONFIG_SYS_INIT_SP_OFFSET
+	swi	r6, r31, GD_MALLOC_BASE
+#endif
 	brai	board_init_f
 #else
+	addi	r31, r0, _gd
+#if defined(CONFIG_SYS_MALLOC_F_LEN)
+	addi	r6, r0, CONFIG_SPL_STACK_ADDR
+	swi	r6, r31, GD_MALLOC_BASE
+#endif
 	brai	board_init_r
 #endif
 1:	bri	1b
 
+ .section .bss
+.align 4
+_gd:
+         .space  GENERATED_GBL_DATA_SIZE
+
 #ifndef CONFIG_SPL_BUILD
 /*
  * Read 16bit little endian
@@ -189,4 +209,108 @@ out16:	bslli	r3, r6, 8
 	rtsd	r15, 8
 	or	r0, r0, r0
 	.end	out16
+
+/*
+ * Relocate u-boot
+ */
+	.text
+	.global	relocate_code
+	.ent	relocate_code
+	.align	2
+relocate_code:
+	/*
+	 * r5 - start_addr_sp
+	 * r6 - new_gd
+	 * r7 - reloc_addr
+	 */
+	addi	r1, r5, 0 /* Start to use new SP */
+	addi	r31, r6, 0 /* Start to use new GD */
+
+	add	r23, r0, r7 /* Move reloc addr to r23 */
+	/* Relocate text and data - r12 temp value */
+	addi	r21, r0, _start
+	addi	r22, r0, __end - 4 /* Include BSS too */
+
+	rsub	r6, r21, r22
+	or	r5, r0, r0
+1:	lw	r12, r21, r5 /* Load u-boot data */
+	sw	r12, r23, r5 /* Write zero to loc */
+	cmp	r12, r5, r6 /* Check if we have reach the end */
+	bneid	r12, 1b
+	addi	r5, r5, 4 /* Increment to next loc - relocate code */
+
+       /* R23 points to the base address. */
+	add	r23, r0, r7 /* Move reloc addr to r23 */
+	addi	r24, r0, CONFIG_SYS_TEXT_BASE /* Get reloc offset */
+	rsub	r23, r24, r23 /* keep - this is already here gd->reloc_off */
+
+	addik	r6, r0, 0x2 /* BIG/LITTLE endian offset */
+	lwi	r7, r0, 0x28
+	swi	r6, r0, 0x28 /* used first unused MB vector */
+	lbui	r10, r0, 0x28 /* used first unused MB vector */
+	swi	r7, r0, 0x28
+
+#ifdef CONFIG_SYS_USR_EXCEP
+	addik	r6, r0, _exception_handler
+	addk	r6, r6, r23 /* add offset */
+	sw	r6, r1, r0
+	lhu	r7, r1, r10
+	rsubi	r8, r10, 0xa
+	sh	r7, r0, r8
+	rsubi	r8, r10, 0xe
+	sh	r6, r0, r8
+#endif
+	addik	r6, r0, _hw_exception_handler
+	addk	r6, r6, r23 /* add offset */
+	sw	r6, r1, r0
+	lhu	r7, r1, r10
+	rsubi	r8, r10, 0x22
+	sh	r7, r0, r8
+	rsubi	r8, r10, 0x26
+	sh	r6, r0, r8
+
+	addik	r6, r0, _interrupt_handler
+	addk	r6, r6, r23 /* add offset */
+	sw	r6, r1, r0
+	lhu	r7, r1, r10
+	rsubi	r8, r10, 0x12
+	sh	r7, r0, r8
+	rsubi	r8, r10, 0x16
+	sh	r6, r0, r8
+
+	/* Check if GOT exist */
+	addik	r21, r23, _got_start
+	addik	r22, r23, _got_end
+	cmpu	r12, r21, r22
+	beqi	r12, 2f /* No GOT table - jump over */
+
+	/* Skip last 3 entries plus 1 because of loop boundary below */
+	addik	r22, r22, -0x10
+
+        /* Relocate the GOT. */
+3:	lw	r12, r21, r0 /* Load entry */
+	addk	r12, r12, r23 /* Add reloc offset */
+	sw	r12, r21, r0 /* Save entry back */
+
+	cmpu	r12, r21, r22 /* Check if this cross boundary */
+	bneid	r12, 3b
+	addik	r21. r21, 4
+
+	/* Update pointer to GOT */
+	mfs	r20, rpc
+	addik	r20, r20, _GLOBAL_OFFSET_TABLE_ + 8
+	addk	r20, r20, r23
+
+	/* Flush caches to ensure consistency */
+	addik	r5, r0, 0
+	addik	r6, r0, XILINX_DCACHE_BYTE_SIZE
+	bralid	r15, flush_cache
+	nop
+
+2:	addi	r5, r31, 0 /* gd is initialized in board_r.c */
+	addi	r6, r0, CONFIG_SYS_TEXT_BASE
+	addi	r12, r23, board_init_r
+	bra	r12 /* Jump to relocated code */
+
+	.end	relocate_code
 #endif

arch/microblaze/cpu/u-boot-spl.lds

@@ -37,6 +37,12 @@ SECTIONS
 		__data_end = .;
 	}
 
+	. = ALIGN(4);
+	.u_boot_list : {
+		KEEP(*(SORT(.u_boot_list*)));
+	}
+	__init_end = . ;
+
 	.bss ALIGN(0x4):
 	{
 		__bss_start = .;

arch/microblaze/cpu/u-boot.lds

@@ -29,17 +29,23 @@ SECTIONS
 	.data ALIGN(0x4):
 	{
 		__data_start = .;
-#ifdef CONFIG_OF_EMBED
-		dts/built-in.o (.data)
-#endif
 		*(.data)
 		__data_end = .;
 	}
 
+	.got ALIGN(4):
+	{
+		_got_start = .;
+		*(.got*)
+		. = ALIGN(4);
+		_got_end = .;
+	}
+
 	. = ALIGN(4);
 	.u_boot_list : {
 		KEEP(*(SORT(.u_boot_list*)));
 	}
+	__init_end = . ;
 
 	.bss ALIGN(0x4):
 	{

arch/microblaze/include/asm/asm.h

@@ -43,6 +43,10 @@
 #define R14(val) \
 	__asm__ __volatile__ ("addi %0, r14, 0":"=r" (val));
 
+/* get return address from interrupt */
+#define R17(val) \
+	__asm__ __volatile__ ("addi %0, r17, 0" : "=r" (val));
+
 #define NOP	__asm__ __volatile__ ("nop");
 
 /* use machine status registe USE_MSR_REG */

arch/microblaze/include/asm/config.h

@@ -7,4 +7,11 @@
 #ifndef _ASM_CONFIG_H_
 #define _ASM_CONFIG_H_
 
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_NEEDS_MANUAL_RELOC
+#endif
+
+#define CONFIG_NR_DRAM_BANKS	1
+#define CONFIG_SYS_GENERIC_BOARD
+
 #endif

arch/microblaze/include/asm/microblaze_intc.h

@@ -34,5 +34,3 @@ struct irq_action {
  */
 int install_interrupt_handler(int irq, interrupt_handler_t *hdlr,
 				       void *arg);
-
-int interrupts_init(void);

arch/microblaze/include/asm/u-boot.h

@@ -16,16 +16,7 @@
 #ifndef _U_BOOT_H_
 #define _U_BOOT_H_
 
-typedef struct bd_info {
-	unsigned long	bi_memstart;	/* start of DRAM memory */
-	phys_size_t	bi_memsize;	/* size	 of DRAM memory in bytes */
-	unsigned long	bi_flashstart;	/* start of FLASH memory */
-	unsigned long	bi_flashsize;	/* size	 of FLASH memory */
-	unsigned long	bi_flashoffset; /* reserved area for startup monitor */
-	unsigned long	bi_sramstart;	/* start of SRAM memory */
-	unsigned long	bi_sramsize;	/* size	 of SRAM memory */
-	ulong		bi_boot_params; /* where this board expects params */
-} bd_t;
+#include <asm-generic/u-boot.h>
 
 /* For image.h:image_check_target_arch() */
 #define IH_ARCH_DEFAULT IH_ARCH_MICROBLAZE

arch/microblaze/lib/Makefile

@@ -5,6 +5,5 @@
 # SPDX-License-Identifier:	GPL-2.0+
 #
 
-obj-y	+= board.o
 obj-$(CONFIG_CMD_BOOTM) += bootm.o
 obj-y	+= muldi3.o

arch/microblaze/lib/board.c

@@ -1,201 +0,0 @@
-/*
- * (C) Copyright 2007 Michal Simek
- * (C) Copyright 2004 Atmark Techno, Inc.
- *
- * Michal  SIMEK <monstr@monstr.eu>
- * Yasushi SHOJI <yashi@atmark-techno.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-#include <malloc.h>
-#include <version.h>
-#include <watchdog.h>
-#include <stdio_dev.h>
-#include <serial.h>
-#include <net.h>
-#include <spi.h>
-#include <linux/compiler.h>
-#include <asm/processor.h>
-#include <asm/microblaze_intc.h>
-#include <fdtdec.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static int display_banner(void)
-{
-	printf("\n\n%s\n\n", version_string);
-	return 0;
-}
-
-/*
- * All attempts to come up with a "common" initialization sequence
- * that works for all boards and architectures failed: some of the
- * requirements are just _too_ different. To get rid of the resulting
- * mess of board dependend #ifdef'ed code we now make the whole
- * initialization sequence configurable to the user.
- *
- * The requirements for any new initalization function is simple: it
- * receives a pointer to the "global data" structure as it's only
- * argument, and returns an integer return code, where 0 means
- * "continue" and != 0 means "fatal error, hang the system".
- */
-typedef int (init_fnc_t) (void);
-
-init_fnc_t *init_sequence[] = {
-	env_init,
-#ifdef CONFIG_OF_CONTROL
-	fdtdec_check_fdt,
-#endif
-	serial_init,
-#ifndef CONFIG_SPL_BUILD
-	console_init_f,
-#endif
-	display_banner,
-#ifndef CONFIG_SPL_BUILD
-	interrupts_init,
-	timer_init,
-#endif
-	NULL,
-};
-
-unsigned long monitor_flash_len;
-
-void board_init_f(ulong not_used)
-{
-	bd_t *bd;
-	init_fnc_t **init_fnc_ptr;
-	gd = (gd_t *)(CONFIG_SYS_SDRAM_BASE + CONFIG_SYS_GBL_DATA_OFFSET);
-	bd = (bd_t *)(CONFIG_SYS_SDRAM_BASE + CONFIG_SYS_GBL_DATA_OFFSET
-						- GENERATED_BD_INFO_SIZE);
-#if defined(CONFIG_CMD_FLASH) && !defined(CONFIG_SPL_BUILD)
-	ulong flash_size = 0;
-#endif
-	asm ("nop");	/* FIXME gd is not initialize - wait */
-	memset((void *)gd, 0, GENERATED_GBL_DATA_SIZE);
-	memset((void *)bd, 0, GENERATED_BD_INFO_SIZE);
-	gd->bd = bd;
-	gd->baudrate = CONFIG_BAUDRATE;
-	bd->bi_memstart = CONFIG_SYS_SDRAM_BASE;
-	bd->bi_memsize = CONFIG_SYS_SDRAM_SIZE;
-	gd->flags |= GD_FLG_RELOC;      /* tell others: relocation done */
-
-	monitor_flash_len = __end - __text_start;
-
-#ifdef CONFIG_OF_EMBED
-	/* Get a pointer to the FDT */
-	gd->fdt_blob = __dtb_dt_begin;
-#elif defined CONFIG_OF_SEPARATE
-	/* FDT is at end of image */
-	gd->fdt_blob = (void *)__end;
-#endif
-
-#ifndef CONFIG_SPL_BUILD
-	/* Allow the early environment to override the fdt address */
-	gd->fdt_blob = (void *)getenv_ulong("fdtcontroladdr", 16,
-						(uintptr_t)gd->fdt_blob);
-#endif
-
-	/*
-	 * The Malloc area is immediately below the monitor copy in DRAM
-	 * aka CONFIG_SYS_MONITOR_BASE - Note there is no need for reloc_off
-	 * as our monitory code is run from SDRAM
-	 */
-	mem_malloc_init(CONFIG_SYS_MALLOC_BASE, CONFIG_SYS_MALLOC_LEN);
-
-	serial_initialize();
-
-#ifdef CONFIG_XILINX_TB_WATCHDOG
-	hw_watchdog_init();
-#endif
-	for (init_fnc_ptr = init_sequence; *init_fnc_ptr; ++init_fnc_ptr) {
-		WATCHDOG_RESET();
-		if ((*init_fnc_ptr) () != 0)
-			hang();
-	}
-
-#ifndef CONFIG_SPL_BUILD
-#ifdef CONFIG_OF_CONTROL
-	/* For now, put this check after the console is ready */
-	if (fdtdec_prepare_fdt())
-		panic("** No FDT - please see doc/README.fdt-control");
-	else
-		printf("DTB: 0x%x\n", (u32)gd->fdt_blob);
-#endif
-
-	puts("SDRAM :\n");
-	printf("\t\tIcache:%s\n", icache_status() ? "ON" : "OFF");
-	printf("\t\tDcache:%s\n", dcache_status() ? "ON" : "OFF");
-	printf("\tU-Boot Start:0x%08x\n", CONFIG_SYS_TEXT_BASE);
-
-#if defined(CONFIG_CMD_FLASH)
-	puts("Flash: ");
-	bd->bi_flashstart = CONFIG_SYS_FLASH_BASE;
-	flash_size = flash_init();
-	if (bd->bi_flashstart && flash_size > 0) {
-# ifdef CONFIG_SYS_FLASH_CHECKSUM
-		print_size(flash_size, "");
-		/*
-		 * Compute and print flash CRC if flashchecksum is set to 'y'
-		 *
-		 * NOTE: Maybe we should add some WATCHDOG_RESET()? XXX
-		 */
-		if (getenv_yesno("flashchecksum") == 1) {
-			printf("  CRC: %08X",
-			       crc32(0, (const u8 *)bd->bi_flashstart,
-				     flash_size)
-			);
-		}
-		putc('\n');
-# else	/* !CONFIG_SYS_FLASH_CHECKSUM */
-		print_size(flash_size, "\n");
-# endif /* CONFIG_SYS_FLASH_CHECKSUM */
-		bd->bi_flashsize = flash_size;
-		bd->bi_flashoffset = bd->bi_flashstart + flash_size;
-	} else {
-		puts("Flash init FAILED");
-		bd->bi_flashstart = 0;
-		bd->bi_flashsize = 0;
-		bd->bi_flashoffset = 0;
-	}
-#endif
-
-#ifdef CONFIG_SPI
-	spi_init();
-#endif
-
-	/* relocate environment function pointers etc. */
-	env_relocate();
-
-	/* Initialize stdio devices */
-	stdio_init();
-
-	/* Initialize the jump table for applications */
-	jumptable_init();
-
-	/* Initialize the console (after the relocation and devices init) */
-	console_init_r();
-
-	board_init();
-
-	/* Initialize from environment */
-	load_addr = getenv_ulong("loadaddr", 16, load_addr);
-
-#if defined(CONFIG_CMD_NET)
-	printf("Net:   ");
-	eth_initialize(gd->bd);
-
-	uchar enetaddr[6];
-	eth_getenv_enetaddr("ethaddr", enetaddr);
-	printf("MAC:   %pM\n", enetaddr);
-#endif
-
-	/* main_loop */
-	for (;;) {
-		WATCHDOG_RESET();
-		main_loop();
-	}
-#endif /* CONFIG_SPL_BUILD */
-}

arch/nds32/include/asm/u-boot-nds32.h

@@ -22,7 +22,6 @@ int	cleanup_before_linux(void);
 
 /* board/.../... */
 int	board_init(void);
-int	dram_init(void);
 
 /* cpu/.../interrupt.c */
 void	reset_timer_masked(void);

arch/sandbox/include/asm/u-boot-sandbox.h

@@ -17,7 +17,6 @@
 
 /* board/.../... */
 int board_init(void);
-int dram_init(void);
 
 /* start.c */
 int sandbox_early_getopt_check(void);

arch/x86/include/asm/u-boot-x86.h

@@ -26,15 +26,9 @@ unsigned long get_tbclk_mhz(void);
 void timer_set_base(uint64_t base);
 int pcat_timer_init(void);
 
-/* Architecture specific DRAM init */
-int dram_init(void);
-
 /* cpu/.../interrupts.c */
 int cpu_init_interrupts(void);
 
-/* board/.../... */
-int dram_init(void);
-
 int cleanup_before_linux(void);
 int x86_cleanup_before_linux(void);
 void x86_enable_caches(void);

board/xilinx/microblaze-generic/microblaze-generic.c

@@ -11,16 +11,62 @@
 
 #include <common.h>
 #include <config.h>
+#include <fdtdec.h>
 #include <netdev.h>
 #include <asm/processor.h>
 #include <asm/microblaze_intc.h>
 #include <asm/asm.h>
 #include <asm/gpio.h>
 
+DECLARE_GLOBAL_DATA_PTR;
+
 #ifdef CONFIG_XILINX_GPIO
 static int reset_pin = -1;
 #endif
 
+#ifdef CONFIG_OF_CONTROL
+ulong ram_base;
+
+void dram_init_banksize(void)
+{
+	gd->bd->bi_dram[0].start = ram_base;
+	gd->bd->bi_dram[0].size = get_effective_memsize();
+}
+
+int dram_init(void)
+{
+	int node;
+	fdt_addr_t addr;
+	fdt_size_t size;
+	const void *blob = gd->fdt_blob;
+
+	node = fdt_node_offset_by_prop_value(blob, -1, "device_type",
+					     "memory", 7);
+	if (node == -FDT_ERR_NOTFOUND) {
+		debug("DRAM: Can't get memory node\n");
+		return 1;
+	}
+	addr = fdtdec_get_addr_size(blob, node, "reg", &size);
+	if (addr == FDT_ADDR_T_NONE || size == 0) {
+		debug("DRAM: Can't get base address or size\n");
+		return 1;
+	}
+	ram_base = addr;
+
+	gd->ram_top = addr; /* In setup_dest_addr() is done +ram_size */
+	gd->ram_size = size;
+
+	return 0;
+};
+#else
+int dram_init(void)
+{
+	gd->ram_size = CONFIG_SYS_SDRAM_SIZE;
+
+	return 0;
+}
+#endif
+
 int do_reset(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 {
 #ifdef CONFIG_XILINX_GPIO

common/board_f.c

@@ -262,7 +262,7 @@ static int zero_global_data(void)
 
 static int setup_mon_len(void)
 {
-#ifdef __ARM__
+#if defined(__ARM__) || defined(__MICROBLAZE__)
 	gd->mon_len = (ulong)&__bss_end - (ulong)_start;
 #elif defined(CONFIG_SANDBOX)
 	gd->mon_len = (ulong)&_end - (ulong)_init;
@@ -909,7 +909,7 @@ static init_fnc_t init_sequence_f[] = {
 #endif
 	announce_dram_init,
 	/* TODO: unify all these dram functions? */
-#if defined(CONFIG_ARM) || defined(CONFIG_X86)
+#if defined(CONFIG_ARM) || defined(CONFIG_X86) || defined(CONFIG_MICROBLAZE)
 	dram_init,		/* configure available RAM banks */
 #endif
 #if defined(CONFIG_MIPS) || defined(CONFIG_PPC)

common/board_r.c

@@ -294,6 +294,15 @@ static int initr_announce(void)
 	return 0;
 }
 
+#ifdef CONFIG_NEEDS_MANUAL_RELOC
+static int initr_manual_reloc_cmdtable(void)
+{
+	fixup_cmdtable(ll_entry_start(cmd_tbl_t, cmd),
+		       ll_entry_count(cmd_tbl_t, cmd));
+	return 0;
+}
+#endif
+
 #if !defined(CONFIG_SYS_NO_FLASH)
 static int initr_flash(void)
 {
@@ -702,6 +711,9 @@ init_fnc_t init_sequence_r[] = {
 	initr_serial,
 	initr_announce,
 	INIT_FUNC_WATCHDOG_RESET
+#ifdef CONFIG_NEEDS_MANUAL_RELOC
+	initr_manual_reloc_cmdtable,
+#endif
 #ifdef CONFIG_PPC
 	initr_trap,
 #endif
@@ -801,7 +813,7 @@ init_fnc_t init_sequence_r[] = {
 #if defined(CONFIG_ARM)
 	initr_enable_interrupts,
 #endif
-#ifdef CONFIG_X86
+#if defined(CONFIG_X86) || defined(CONFIG_MICROBLAZE)
 	timer_init,		/* initialize timer */
 #endif
 #if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)

common/cmd_bdinfo.c

@@ -183,8 +183,14 @@ int do_bdinfo(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 int do_bdinfo(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 {
 	bd_t *bd = gd->bd;
-	print_num("mem start      ",	(ulong)bd->bi_memstart);
-	print_lnum("mem size       ",	(u64)bd->bi_memsize);
+	int i;
+
+	for (i = 0; i < CONFIG_NR_DRAM_BANKS; ++i) {
+		print_num("DRAM bank",	i);
+		print_num("-> start",	bd->bi_dram[i].start);
+		print_num("-> size",	bd->bi_dram[i].size);
+	}
+
 	print_num("flash start    ",	(ulong)bd->bi_flashstart);
 	print_num("flash size     ",	(ulong)bd->bi_flashsize);
 	print_num("flash offset   ",	(ulong)bd->bi_flashoffset);
@@ -196,6 +202,12 @@ int do_bdinfo(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 	print_eths();
 #endif
 	printf("baudrate    = %u bps\n", gd->baudrate);
+	print_num("relocaddr", gd->relocaddr);
+	print_num("reloc off", gd->reloc_off);
+	print_num("fdt_blob", (ulong)gd->fdt_blob);
+	print_num("new_fdt", (ulong)gd->new_fdt);
+	print_num("fdt_size", (ulong)gd->fdt_size);
+
 	return 0;
 }
 

include/common.h

@@ -183,6 +183,7 @@ typedef void (interrupt_handler_t)(void *);
 /*
  * Function Prototypes
  */
+int dram_init(void);
 
 void	hang		(void) __attribute__ ((noreturn));
 

include/configs/microblaze-generic.h

@@ -106,62 +106,22 @@
 # define CONFIG_XILINX_TB_WATCHDOG
 #endif
 
-/*
- * memory layout - Example
- * CONFIG_SYS_TEXT_BASE = 0x1200_0000;	defined in config.mk
- * CONFIG_SYS_SRAM_BASE = 0x1000_0000;
- * CONFIG_SYS_SRAM_SIZE = 0x0400_0000;	64MB
- *
- * CONFIG_SYS_MONITOR_LEN = 0x40000
- * CONFIG_SYS_MALLOC_LEN = 3 * CONFIG_SYS_MONITOR_LEN = 0xC0000
- *
- * CONFIG_SYS_GBL_DATA_OFFSET = 0x1000_0000 + 0x0400_0000 - 0x1000 = 0x13FF_F000
- * CONFIG_SYS_MONITOR_BASE = 0x13FF_F000 - CONFIG_SYS_MONITOR_LEN = 0x13FB_F000
- * CONFIG_SYS_MALLOC_BASE = 0x13FB_F000 - CONFIG_SYS_MALLOC_LEN = 0x13EF_F000
- *
- * 0x1000_0000	CONFIG_SYS_SDRAM_BASE
- *					MEMTEST_AREA	 64kB
- *					FREE
- * 0x1200_0000	CONFIG_SYS_TEXT_BASE
- *		U-BOOT code
- * 0x1202_0000
- *					FREE
- *
- *					STACK
- * 0x13EF_F000	CONFIG_SYS_MALLOC_BASE
- *					MALLOC_AREA	768kB	Alloc
- * 0x13FB_F000	CONFIG_SYS_MONITOR_BASE
- *					MONITOR_CODE	256kB	Env
- * 0x13FF_F000	CONFIG_SYS_GBL_DATA_OFFSET
- *					GLOBAL_DATA	4kB	bd, gd
- * 0x1400_0000	CONFIG_SYS_SDRAM_BASE + CONFIG_SYS_SDRAM_SIZE
- */
-
+#ifndef CONFIG_OF_CONTROL
 /* ddr sdram - main memory */
-#define	CONFIG_SYS_SDRAM_BASE		XILINX_RAM_START
-#define	CONFIG_SYS_SDRAM_SIZE		XILINX_RAM_SIZE
-#define	CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
-#define	CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_SDRAM_BASE + 0x1000)
-
-/* global pointer */
-/* start of global data */
-#define	CONFIG_SYS_GBL_DATA_OFFSET \
-		(CONFIG_SYS_SDRAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-/* monitor code */
-#define	SIZE				0x40000
-#define	CONFIG_SYS_MONITOR_LEN		SIZE
-#define	CONFIG_SYS_MONITOR_BASE	\
-		(CONFIG_SYS_SDRAM_BASE + CONFIG_SYS_GBL_DATA_OFFSET \
-			- CONFIG_SYS_MONITOR_LEN - GENERATED_BD_INFO_SIZE)
-#define	CONFIG_SYS_MONITOR_END \
-			(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-#define	CONFIG_SYS_MALLOC_LEN		(SIZE * 3)
-#define	CONFIG_SYS_MALLOC_BASE \
-			(CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
-
-/* stack */
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_MALLOC_BASE
+# define CONFIG_SYS_SDRAM_BASE	XILINX_RAM_START
+# define CONFIG_SYS_SDRAM_SIZE	XILINX_RAM_SIZE
+#endif
+
+#define CONFIG_SYS_MALLOC_LEN	0xC0000
+#ifndef CONFIG_SPL_BUILD
+# define CONFIG_SYS_MALLOC_F_LEN	1024
+#else
+# define CONFIG_SYS_MALLOC_SIMPLE
+# define CONFIG_SYS_MALLOC_F_LEN	0x150
+#endif
+
+/* Stack location before relocation */
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_TEXT_BASE
 
 /*
  * CFI flash memory layout - Example
@@ -452,7 +412,10 @@
 #define CONFIG_SPL_LDSCRIPT	"arch/microblaze/cpu/u-boot-spl.lds"
 
 #define CONFIG_SPL_RAM_DEVICE
-#define CONFIG_SPL_NOR_SUPPORT
+#ifdef CONFIG_SYS_FLASH_BASE
+# define CONFIG_SPL_NOR_SUPPORT
+# define CONFIG_SYS_UBOOT_BASE		CONFIG_SYS_FLASH_BASE
+#endif
 
 /* for booting directly linux */
 #define CONFIG_SPL_OS_BOOT
@@ -468,36 +431,20 @@
 /* BRAM start */
 #define CONFIG_SYS_INIT_RAM_ADDR	0x0
 /* BRAM size - will be generated */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x10000
-/* Stack pointer prior relocation, must situated at on-chip RAM */
-#define CONFIG_SYS_SPL_MALLOC_END	(CONFIG_SYS_INIT_RAM_ADDR + \
-					 CONFIG_SYS_INIT_RAM_SIZE - \
-					 GENERATED_GBL_DATA_SIZE)
-
-#define CONFIG_SYS_SPL_MALLOC_SIZE	0x100
+#define CONFIG_SYS_INIT_RAM_SIZE	0x100000
 
-/*
- * The main reason to do it in this way is that MALLOC_START
- * can't be defined - common/spl/spl.c
- */
-#if (CONFIG_SYS_SPL_MALLOC_SIZE != 0)
-# define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SYS_SPL_MALLOC_END - \
-					 CONFIG_SYS_SPL_MALLOC_SIZE)
-# define CONFIG_SPL_STACK_ADDR		CONFIG_SYS_SPL_MALLOC_START
-#else
-# define CONFIG_SPL_STACK_ADDR		CONFIG_SYS_SPL_MALLOC_END
-#endif
+# define CONFIG_SPL_STACK_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + \
+					 CONFIG_SYS_INIT_RAM_SIZE - \
+					 CONFIG_SYS_MALLOC_F_LEN)
 
 /* Just for sure that there is a space for stack */
 #define CONFIG_SPL_STACK_SIZE		0x100
 
-#define CONFIG_SYS_UBOOT_BASE		CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_UBOOT_START		CONFIG_SYS_TEXT_BASE
 
 #define CONFIG_SPL_MAX_FOOTPRINT	(CONFIG_SYS_INIT_RAM_SIZE - \
 					 CONFIG_SYS_INIT_RAM_ADDR - \
-					 GENERATED_GBL_DATA_SIZE - \
-					 CONFIG_SYS_SPL_MALLOC_SIZE - \
+					 CONFIG_SYS_MALLOC_F_LEN - \
 					 CONFIG_SPL_STACK_SIZE)
 
 #endif	/* __CONFIG_H */