phy: marvell: a3700: Use reg_set_indirect istead of 2 reg_sets

Create a special function for indirect register setting,
reg_set_indirect, and use it instead of the two calls to reg_set.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>

drivers/phy/marvell/comphy_a3700.c

@@ -223,6 +223,17 @@ static int comphy_pcie_power_up(u32 speed, u32 invert)
 	return ret;
 }
 
+/*
+ * reg_set_indirect
+ *
+ * return: void
+ */
+static void reg_set_indirect(u32 reg, u16 data, u16 mask)
+{
+	reg_set(rh_vsreg_addr, reg, 0xFFFFFFFF);
+	reg_set(rh_vsreg_data, data, mask);
+}
+
 /*
  * comphy_sata_power_up
  *
@@ -230,43 +241,40 @@ static int comphy_pcie_power_up(u32 speed, u32 invert)
  */
 static int comphy_sata_power_up(void)
 {
-	int	ret;
+	int ret;
 
 	debug_enter();
 
 	/*
 	 * 0. Swap SATA TX lines
 	 */
-	reg_set(rh_vsreg_addr, vphy_sync_pattern_reg, 0xFFFFFFFF);
-	reg_set(rh_vsreg_data, bs_txd_inv, bs_txd_inv);
+	reg_set_indirect(vphy_sync_pattern_reg, bs_txd_inv, bs_txd_inv);
 
 	/*
 	 * 1. Select 40-bit data width width
 	 */
-	reg_set(rh_vsreg_addr, vphy_loopback_reg0, 0xFFFFFFFF);
-	reg_set(rh_vsreg_data, 0x800, bs_phyintf_40bit);
+	reg_set_indirect(vphy_loopback_reg0, 0x800, bs_phyintf_40bit);
 
 	/*
 	 * 2. Select reference clock and PHY mode (SATA)
 	 */
-	reg_set(rh_vsreg_addr, vphy_power_reg0, 0xFFFFFFFF);
 	if (get_ref_clk() == 40) {
-		reg_set(rh_vsreg_data, 0x3, 0x00FF); /* 40 MHz */
+		/* 40 MHz */
+		reg_set_indirect(vphy_power_reg0, 0x3, 0x00FF);
 	} else {
-		reg_set(rh_vsreg_data, 0x1, 0x00FF); /* 25 MHz */
+		/* 20 MHz */
+		reg_set_indirect(vphy_power_reg0, 0x1, 0x00FF);
 	}
 
 	/*
 	 * 3. Use maximum PLL rate (no power save)
 	 */
-	reg_set(rh_vsreg_addr, vphy_calctl_reg, 0xFFFFFFFF);
-	reg_set(rh_vsreg_data, bs_max_pll_rate, bs_max_pll_rate);
+	reg_set_indirect(vphy_calctl_reg, bs_max_pll_rate, bs_max_pll_rate);
 
 	/*
 	 * 4. Reset reserved bit (??)
 	 */
-	reg_set(rh_vsreg_addr, vphy_reserve_reg, 0xFFFFFFFF);
-	reg_set(rh_vsreg_data, 0, bs_phyctrl_frm_pin);
+	reg_set_indirect(vphy_reserve_reg, 0, bs_phyctrl_frm_pin);
 
 	/*
 	 * 5. Set vendor-specific configuration (??)