net/designware - switch driver to phylib usage

With this change driver will benefit from existing phylib and thus
custom phy functionality implemented in the driver will go away:
 * Instantiation of the driver is now much shorter - 2 parameters
instead of 4.
 * Simplified phy management/functoinality in driver is replaced with
rich functionality of phylib.
 * Support of custom phy initialization is now done with existing
"board_phy_config".

Note that after this change some previously used config options
(driver-specific PHY configuration) will be obsolete and they are simply
substituted with similar options of phylib.

For example:
 * CONFIG_DW_AUTONEG - no need in this one. Autonegotiation is enabled
by default.
 * CONFIG_DW_SEARCH_PHY - if one wants to specify attached phy
explicitly CONFIG_PHY_ADDR board config option has to be used, otherwise
automatically the first discovered on MDIO bus phy will be used

I believe there's no need now in "doc/README.designware_eth" because
user only needs to instantiate the driver with "designware_initialize"
whose prototype exists in "include/netdev.h".

Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

board/bf609-ezkit/bf609-ezkit.c

@@ -41,12 +41,12 @@ int board_eth_init(bd_t *bis)
 	if (CONFIG_DW_PORTS & 1) {
 		static const unsigned short pins[] = P_RMII0;
 		if (!peripheral_request_list(pins, "emac0"))
-			ret += designware_initialize(0, EMAC0_MACCFG, 1, 0);
+			ret += designware_initialize(EMAC0_MACCFG, 0);
 	}
 	if (CONFIG_DW_PORTS & 2) {
 		static const unsigned short pins[] = P_RMII1;
 		if (!peripheral_request_list(pins, "emac1"))
-			ret += designware_initialize(1, EMAC1_MACCFG, 1, 0);
+			ret += designware_initialize(EMAC1_MACCFG, 0);
 	}
 
 	return ret;

board/spear/spear300/spear300.c

@@ -53,8 +53,7 @@ int board_eth_init(bd_t *bis)
 
 #if defined(CONFIG_DESIGNWARE_ETH)
 	u32 interface = PHY_INTERFACE_MODE_MII;
-	if (designware_initialize(0, CONFIG_SPEAR_ETHBASE, CONFIG_DW0_PHY,
-				interface) >= 0)
+	if (designware_initialize(CONFIG_SPEAR_ETHBASE, interface) >= 0)
 		ret++;
 #endif
 	return ret;

board/spear/spear310/spear310.c

@@ -54,8 +54,7 @@ int board_eth_init(bd_t *bis)
 
 #if defined(CONFIG_DESIGNWARE_ETH)
 	u32 interface = PHY_INTERFACE_MODE_MII;
-	if (designware_initialize(0, CONFIG_SPEAR_ETHBASE, CONFIG_DW0_PHY,
-				interface) >= 0)
+	if (designware_initialize(CONFIG_SPEAR_ETHBASE, interface) >= 0)
 		ret++;
 #endif
 #if defined(CONFIG_MACB)

board/spear/spear320/spear320.c

@@ -65,8 +65,7 @@ int board_eth_init(bd_t *bis)
 
 #if defined(CONFIG_DESIGNWARE_ETH)
 	u32 interface = PHY_INTERFACE_MODE_MII;
-	if (designware_initialize(0, CONFIG_SPEAR_ETHBASE, CONFIG_DW0_PHY,
-				interface) >= 0)
+	if (designware_initialize(CONFIG_SPEAR_ETHBASE, interface) >= 0)
 		ret++;
 #endif
 #if defined(CONFIG_MACB)

board/spear/spear600/spear600.c

@@ -51,8 +51,7 @@ int board_eth_init(bd_t *bis)
 #if defined(CONFIG_DW_AUTONEG)
 	interface = PHY_INTERFACE_MODE_GMII;
 #endif
-	if (designware_initialize(0, CONFIG_SPEAR_ETHBASE, CONFIG_DW0_PHY,
-				interface) >= 0)
+	if (designware_initialize(CONFIG_SPEAR_ETHBASE, interface) >= 0)
 		ret++;
 #endif
 	return ret;

board/spear/x600/x600.c

@@ -67,31 +67,32 @@ void board_nand_init(void)
 		fsmc_nand_init(nand);
 }
 
-int designware_board_phy_init(struct eth_device *dev, int phy_addr,
-	int (*mii_write)(struct eth_device *, u8, u8, u16),
-	int dw_reset_phy(struct eth_device *))
+int board_phy_config(struct phy_device *phydev)
 {
 	/* Extended PHY control 1, select GMII */
-	mii_write(dev, phy_addr, 23, 0x0020);
+	phy_write(phydev, MDIO_DEVAD_NONE, 23, 0x0020);
 
 	/* Software reset necessary after GMII mode selction */
-	dw_reset_phy(dev);
+	phy_reset(phydev);
 
 	/* Enable extended page register access */
-	mii_write(dev, phy_addr, 31, 0x0001);
+	phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0001);
 
 	/* 17e: Enhanced LED behavior, needs to be written twice */
-	mii_write(dev, phy_addr, 17, 0x09ff);
-	mii_write(dev, phy_addr, 17, 0x09ff);
+	phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff);
+	phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff);
 
 	/* 16e: Enhanced LED method select */
-	mii_write(dev, phy_addr, 16, 0xe0ea);
+	phy_write(phydev, MDIO_DEVAD_NONE, 16, 0xe0ea);
 
 	/* Disable extended page register access */
-	mii_write(dev, phy_addr, 31, 0x0000);
+	phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0000);
 
 	/* Enable clock output pin */
-	mii_write(dev, phy_addr, 18, 0x0049);
+	phy_write(phydev, MDIO_DEVAD_NONE, 18, 0x0049);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
 
 	return 0;
 }
@@ -100,7 +101,7 @@ int board_eth_init(bd_t *bis)
 {
 	int ret = 0;
 
-	if (designware_initialize(0, CONFIG_SPEAR_ETHBASE, CONFIG_PHY_ADDR,
+	if (designware_initialize(CONFIG_SPEAR_ETHBASE,
 				  PHY_INTERFACE_MODE_GMII) >= 0)
 		ret++;
 

doc/README.designware_eth

@@ -1,25 +0,0 @@
-This driver supports Designware Ethernet Controller provided by Synopsis.
-
-The driver is enabled by CONFIG_DESIGNWARE_ETH.
-
-The driver has been developed and tested on SPEAr platforms. By default, the
-MDIO interface works at 100/Full. #defining the below options in board
-configuration file changes this behavior.
-
-Call an subroutine from respective board/.../board.c
-designware_initialize(u32 id, ulong base_addr, u32 phy_addr);
-
-The various options suported by the driver are
-1. CONFIG_DW_ALTDESCRIPTOR
-	Define this to use the Alternate/Enhanced Descriptor configurations.
-1. CONFIG_DW_AUTONEG
-	Define this to autonegotiate with the host before proceeding with mac
-	level configuration. This obviates the definitions of CONFIG_DW_SPEED10M
-	and CONFIG_DW_DUPLEXHALF.
-2. CONFIG_DW_SPEED10M
-	Define this to change the default behavior from 100Mbps to 10Mbps.
-3. CONFIG_DW_DUPLEXHALF
-	Define this to change the default behavior from Full Duplex to Half.
-4. CONFIG_DW_SEARCH_PHY
-	Define this to search the phy address. This would overwrite the value
-	passed as 3rd arg from designware_initialize routine.

drivers/net/designware.c

@@ -17,7 +17,75 @@
 #include <asm/io.h>
 #include "designware.h"
 
-static int configure_phy(struct eth_device *dev);
+#if !defined(CONFIG_PHYLIB)
+# error "DesignWare Ether MAC requires PHYLIB - missing CONFIG_PHYLIB"
+#endif
+
+static int dw_mdio_read(struct mii_dev *bus, int addr, int devad, int reg)
+{
+	struct eth_mac_regs *mac_p = bus->priv;
+	ulong start;
+	u16 miiaddr;
+	int timeout = CONFIG_MDIO_TIMEOUT;
+
+	miiaddr = ((addr << MIIADDRSHIFT) & MII_ADDRMSK) |
+		  ((reg << MIIREGSHIFT) & MII_REGMSK);
+
+	writel(miiaddr | MII_CLKRANGE_150_250M | MII_BUSY, &mac_p->miiaddr);
+
+	start = get_timer(0);
+	while (get_timer(start) < timeout) {
+		if (!(readl(&mac_p->miiaddr) & MII_BUSY))
+			return readl(&mac_p->miidata);
+		udelay(10);
+	};
+
+	return -1;
+}
+
+static int dw_mdio_write(struct mii_dev *bus, int addr, int devad, int reg,
+			u16 val)
+{
+	struct eth_mac_regs *mac_p = bus->priv;
+	ulong start;
+	u16 miiaddr;
+	int ret = -1, timeout = CONFIG_MDIO_TIMEOUT;
+
+	writel(val, &mac_p->miidata);
+	miiaddr = ((addr << MIIADDRSHIFT) & MII_ADDRMSK) |
+		  ((reg << MIIREGSHIFT) & MII_REGMSK) | MII_WRITE;
+
+	writel(miiaddr | MII_CLKRANGE_150_250M | MII_BUSY, &mac_p->miiaddr);
+
+	start = get_timer(0);
+	while (get_timer(start) < timeout) {
+		if (!(readl(&mac_p->miiaddr) & MII_BUSY)) {
+			ret = 0;
+			break;
+		}
+		udelay(10);
+	};
+
+	return ret;
+}
+
+static int dw_mdio_init(char *name, struct eth_mac_regs *mac_regs_p)
+{
+	struct mii_dev *bus = mdio_alloc();
+
+	if (!bus) {
+		printf("Failed to allocate MDIO bus\n");
+		return -1;
+	}
+
+	bus->read = dw_mdio_read;
+	bus->write = dw_mdio_write;
+	sprintf(bus->name, name);
+
+	bus->priv = (void *)mac_regs_p;
+
+	return mdio_register(bus);
+}
 
 static void tx_descs_init(struct eth_device *dev)
 {
@@ -83,53 +151,59 @@ static void rx_descs_init(struct eth_device *dev)
 	priv->rx_currdescnum = 0;
 }
 
-static void descs_init(struct eth_device *dev)
+static int dw_write_hwaddr(struct eth_device *dev)
 {
-	tx_descs_init(dev);
-	rx_descs_init(dev);
+	struct dw_eth_dev *priv = dev->priv;
+	struct eth_mac_regs *mac_p = priv->mac_regs_p;
+	u32 macid_lo, macid_hi;
+	u8 *mac_id = &dev->enetaddr[0];
+
+	macid_lo = mac_id[0] + (mac_id[1] << 8) + (mac_id[2] << 16) +
+		   (mac_id[3] << 24);
+	macid_hi = mac_id[4] + (mac_id[5] << 8);
+
+	writel(macid_hi, &mac_p->macaddr0hi);
+	writel(macid_lo, &mac_p->macaddr0lo);
+
+	return 0;
 }
 
-static int mac_reset(struct eth_device *dev)
+static void dw_adjust_link(struct eth_mac_regs *mac_p,
+			   struct phy_device *phydev)
 {
-	struct dw_eth_dev *priv = dev->priv;
-	struct eth_mac_regs *mac_p = priv->mac_regs_p;
-	struct eth_dma_regs *dma_p = priv->dma_regs_p;
+	u32 conf = readl(&mac_p->conf) | FRAMEBURSTENABLE | DISABLERXOWN;
 
-	ulong start;
-	int timeout = CONFIG_MACRESET_TIMEOUT;
+	if (!phydev->link) {
+		printf("%s: No link.\n", phydev->dev->name);
+		return;
+	}
 
-	writel(readl(&dma_p->busmode) | DMAMAC_SRST, &dma_p->busmode);
+	if (phydev->speed != 1000)
+		conf |= MII_PORTSELECT;
 
-	if (priv->interface != PHY_INTERFACE_MODE_RGMII)
-		writel(MII_PORTSELECT, &mac_p->conf);
+	if (phydev->speed == 100)
+		conf |= FES_100;
 
-	start = get_timer(0);
-	while (get_timer(start) < timeout) {
-		if (!(readl(&dma_p->busmode) & DMAMAC_SRST))
-			return 0;
+	if (phydev->duplex)
+		conf |= FULLDPLXMODE;
 
-		/* Try again after 10usec */
-		udelay(10);
-	};
+	writel(conf, &mac_p->conf);
 
-	return -1;
+	printf("Speed: %d, %s duplex%s\n", phydev->speed,
+	       (phydev->duplex) ? "full" : "half",
+	       (phydev->port == PORT_FIBRE) ? ", fiber mode" : "");
 }
 
-static int dw_write_hwaddr(struct eth_device *dev)
+static void dw_eth_halt(struct eth_device *dev)
 {
 	struct dw_eth_dev *priv = dev->priv;
 	struct eth_mac_regs *mac_p = priv->mac_regs_p;
-	u32 macid_lo, macid_hi;
-	u8 *mac_id = &dev->enetaddr[0];
+	struct eth_dma_regs *dma_p = priv->dma_regs_p;
 
-	macid_lo = mac_id[0] + (mac_id[1] << 8) + \
-		   (mac_id[2] << 16) + (mac_id[3] << 24);
-	macid_hi = mac_id[4] + (mac_id[5] << 8);
+	writel(readl(&mac_p->conf) & ~(RXENABLE | TXENABLE), &mac_p->conf);
+	writel(readl(&dma_p->opmode) & ~(RXSTART | TXSTART), &dma_p->opmode);
 
-	writel(macid_hi, &mac_p->macaddr0hi);
-	writel(macid_lo, &mac_p->macaddr0lo);
-
-	return 0;
+	phy_shutdown(priv->phydev);
 }
 
 static int dw_eth_init(struct eth_device *dev, bd_t *bis)
@@ -137,55 +211,43 @@ static int dw_eth_init(struct eth_device *dev, bd_t *bis)
 	struct dw_eth_dev *priv = dev->priv;
 	struct eth_mac_regs *mac_p = priv->mac_regs_p;
 	struct eth_dma_regs *dma_p = priv->dma_regs_p;
-	u32 conf;
+	unsigned int start;
 
-	if (priv->phy_configured != 1)
-		configure_phy(dev);
+	writel(readl(&dma_p->busmode) | DMAMAC_SRST, &dma_p->busmode);
 
-	/* Print link status only once */
-	if (!priv->link_printed) {
-		printf("ENET Speed is %d Mbps - %s duplex connection\n",
-		       priv->speed, (priv->duplex == HALF) ? "HALF" : "FULL");
-		priv->link_printed = 1;
-	}
+	start = get_timer(0);
+	while (readl(&dma_p->busmode) & DMAMAC_SRST) {
+		if (get_timer(start) >= CONFIG_MACRESET_TIMEOUT)
+			return -1;
 
-	/* Reset ethernet hardware */
-	if (mac_reset(dev) < 0)
-		return -1;
+		mdelay(100);
+	};
 
-	/* Resore the HW MAC address as it has been lost during MAC reset */
+	/* Soft reset above clears HW address registers.
+	 * So we have to set it here once again */
 	dw_write_hwaddr(dev);
 
-	writel(FIXEDBURST | PRIORXTX_41 | BURST_16,
-			&dma_p->busmode);
-
-	writel(readl(&dma_p->opmode) | FLUSHTXFIFO | STOREFORWARD |
-		TXSECONDFRAME, &dma_p->opmode);
+	rx_descs_init(dev);
+	tx_descs_init(dev);
 
-	conf = FRAMEBURSTENABLE | DISABLERXOWN;
+	writel(FIXEDBURST | PRIORXTX_41 | BURST_16, &dma_p->busmode);
 
-	if (priv->speed != 1000)
-		conf |= MII_PORTSELECT;
+	writel(readl(&dma_p->opmode) | FLUSHTXFIFO | STOREFORWARD,
+	       &dma_p->opmode);
 
-	if ((priv->interface != PHY_INTERFACE_MODE_MII) &&
-		(priv->interface != PHY_INTERFACE_MODE_GMII)) {
+	writel(readl(&dma_p->opmode) | RXSTART | TXSTART, &dma_p->opmode);
 
-		if (priv->speed == 100)
-			conf |= FES_100;
+	/* Start up the PHY */
+	if (phy_startup(priv->phydev)) {
+		printf("Could not initialize PHY %s\n",
+		       priv->phydev->dev->name);
+		return -1;
 	}
 
-	if (priv->duplex == FULL)
-		conf |= FULLDPLXMODE;
-
-	writel(conf, &mac_p->conf);
+	dw_adjust_link(mac_p, priv->phydev);
 
-	descs_init(dev);
-
-	/*
-	 * Start/Enable xfer at dma as well as mac level
-	 */
-	writel(readl(&dma_p->opmode) | RXSTART, &dma_p->opmode);
-	writel(readl(&dma_p->opmode) | TXSTART, &dma_p->opmode);
+	if (!priv->phydev->link)
+		return -1;
 
 	writel(readl(&mac_p->conf) | RXENABLE | TXENABLE, &mac_p->conf);
 
@@ -267,251 +329,30 @@ static int dw_eth_recv(struct eth_device *dev)
 	return length;
 }
 
-static void dw_eth_halt(struct eth_device *dev)
-{
-	struct dw_eth_dev *priv = dev->priv;
-
-	mac_reset(dev);
-	priv->tx_currdescnum = priv->rx_currdescnum = 0;
-}
-
-static int eth_mdio_read(struct eth_device *dev, u8 addr, u8 reg, u16 *val)
+static int dw_phy_init(struct eth_device *dev)
 {
 	struct dw_eth_dev *priv = dev->priv;
-	struct eth_mac_regs *mac_p = priv->mac_regs_p;
-	ulong start;
-	u32 miiaddr;
-	int timeout = CONFIG_MDIO_TIMEOUT;
-
-	miiaddr = ((addr << MIIADDRSHIFT) & MII_ADDRMSK) | \
-		  ((reg << MIIREGSHIFT) & MII_REGMSK);
-
-	writel(miiaddr | MII_CLKRANGE_150_250M | MII_BUSY, &mac_p->miiaddr);
-
-	start = get_timer(0);
-	while (get_timer(start) < timeout) {
-		if (!(readl(&mac_p->miiaddr) & MII_BUSY)) {
-			*val = readl(&mac_p->miidata);
-			return 0;
-		}
+	struct phy_device *phydev;
+	int mask = 0xffffffff;
 
-		/* Try again after 10usec */
-		udelay(10);
-	};
-
-	return -1;
-}
-
-static int eth_mdio_write(struct eth_device *dev, u8 addr, u8 reg, u16 val)
-{
-	struct dw_eth_dev *priv = dev->priv;
-	struct eth_mac_regs *mac_p = priv->mac_regs_p;
-	ulong start;
-	u32 miiaddr;
-	int ret = -1, timeout = CONFIG_MDIO_TIMEOUT;
-	u16 value;
-
-	writel(val, &mac_p->miidata);
-	miiaddr = ((addr << MIIADDRSHIFT) & MII_ADDRMSK) | \
-		  ((reg << MIIREGSHIFT) & MII_REGMSK) | MII_WRITE;
-
-	writel(miiaddr | MII_CLKRANGE_150_250M | MII_BUSY, &mac_p->miiaddr);
-
-	start = get_timer(0);
-	while (get_timer(start) < timeout) {
-		if (!(readl(&mac_p->miiaddr) & MII_BUSY)) {
-			ret = 0;
-			break;
-		}
-
-		/* Try again after 10usec */
-		udelay(10);
-	};
-
-	/* Needed as a fix for ST-Phy */
-	eth_mdio_read(dev, addr, reg, &value);
-
-	return ret;
-}
-
-#if defined(CONFIG_DW_SEARCH_PHY)
-static int find_phy(struct eth_device *dev)
-{
-	int phy_addr = 0;
-	u16 ctrl, oldctrl;
-
-	do {
-		eth_mdio_read(dev, phy_addr, MII_BMCR, &ctrl);
-		oldctrl = ctrl & BMCR_ANENABLE;
-
-		ctrl ^= BMCR_ANENABLE;
-		eth_mdio_write(dev, phy_addr, MII_BMCR, ctrl);
-		eth_mdio_read(dev, phy_addr, MII_BMCR, &ctrl);
-		ctrl &= BMCR_ANENABLE;
-
-		if (ctrl == oldctrl) {
-			phy_addr++;
-		} else {
-			ctrl ^= BMCR_ANENABLE;
-			eth_mdio_write(dev, phy_addr, MII_BMCR, ctrl);
-
-			return phy_addr;
-		}
-	} while (phy_addr < 32);
-
-	return -1;
-}
+#ifdef CONFIG_PHY_ADDR
+	mask = 1 << CONFIG_PHY_ADDR;
 #endif
 
-static int dw_reset_phy(struct eth_device *dev)
-{
-	struct dw_eth_dev *priv = dev->priv;
-	u16 ctrl;
-	ulong start;
-	int timeout = CONFIG_PHYRESET_TIMEOUT;
-	u32 phy_addr = priv->address;
-
-	eth_mdio_write(dev, phy_addr, MII_BMCR, BMCR_RESET);
-
-	start = get_timer(0);
-	while (get_timer(start) < timeout) {
-		eth_mdio_read(dev, phy_addr, MII_BMCR, &ctrl);
-		if (!(ctrl & BMCR_RESET))
-			break;
-
-		/* Try again after 10usec */
-		udelay(10);
-	};
-
-	if (get_timer(start) >= CONFIG_PHYRESET_TIMEOUT)
+	phydev = phy_find_by_mask(priv->bus, mask, priv->interface);
+	if (!phydev)
 		return -1;
 
-#ifdef CONFIG_PHY_RESET_DELAY
-	udelay(CONFIG_PHY_RESET_DELAY);
-#endif
-	return 0;
-}
+	phydev->supported &= PHY_GBIT_FEATURES;
+	phydev->advertising = phydev->supported;
 
-/*
- * Add weak default function for board specific PHY configuration
- */
-int __weak designware_board_phy_init(struct eth_device *dev, int phy_addr,
-		int (*mii_write)(struct eth_device *, u8, u8, u16),
-		int dw_reset_phy(struct eth_device *))
-{
-	return 0;
-}
+	priv->phydev = phydev;
+	phy_config(phydev);
 
-static int configure_phy(struct eth_device *dev)
-{
-	struct dw_eth_dev *priv = dev->priv;
-	int phy_addr;
-	u16 bmcr;
-#if defined(CONFIG_DW_AUTONEG)
-	u16 bmsr;
-	u32 timeout;
-	ulong start;
-#endif
-
-#if defined(CONFIG_DW_SEARCH_PHY)
-	phy_addr = find_phy(dev);
-	if (phy_addr >= 0)
-		priv->address = phy_addr;
-	else
-		return -1;
-#else
-	phy_addr = priv->address;
-#endif
-
-	/*
-	 * Some boards need board specific PHY initialization. This is
-	 * after the main driver init code but before the auto negotiation
-	 * is run.
-	 */
-	if (designware_board_phy_init(dev, phy_addr,
-				      eth_mdio_write, dw_reset_phy) < 0)
-		return -1;
-
-	if (dw_reset_phy(dev) < 0)
-		return -1;
-
-#if defined(CONFIG_DW_AUTONEG)
-	/* Set Auto-Neg Advertisement capabilities to 10/100 half/full */
-	eth_mdio_write(dev, phy_addr, MII_ADVERTISE, 0x1E1);
-
-	bmcr = BMCR_ANENABLE | BMCR_ANRESTART;
-#else
-	bmcr = BMCR_SPEED100 | BMCR_FULLDPLX;
-
-#if defined(CONFIG_DW_SPEED10M)
-	bmcr &= ~BMCR_SPEED100;
-#endif
-#if defined(CONFIG_DW_DUPLEXHALF)
-	bmcr &= ~BMCR_FULLDPLX;
-#endif
-#endif
-	if (eth_mdio_write(dev, phy_addr, MII_BMCR, bmcr) < 0)
-		return -1;
-
-	/* Read the phy status register and populate priv structure */
-#if defined(CONFIG_DW_AUTONEG)
-	timeout = CONFIG_AUTONEG_TIMEOUT;
-	start = get_timer(0);
-	puts("Waiting for PHY auto negotiation to complete");
-	while (get_timer(start) < timeout) {
-		eth_mdio_read(dev, phy_addr, MII_BMSR, &bmsr);
-		if (bmsr & BMSR_ANEGCOMPLETE) {
-			priv->phy_configured = 1;
-			break;
-		}
-
-		/* Print dot all 1s to show progress */
-		if ((get_timer(start) % 1000) == 0)
-			putc('.');
-
-		/* Try again after 1msec */
-		udelay(1000);
-	};
-
-	if (!(bmsr & BMSR_ANEGCOMPLETE))
-		puts(" TIMEOUT!\n");
-	else
-		puts(" done\n");
-#else
-	priv->phy_configured = 1;
-#endif
-
-	priv->speed = miiphy_speed(dev->name, phy_addr);
-	priv->duplex = miiphy_duplex(dev->name, phy_addr);
-
-	return 0;
-}
-
-#if defined(CONFIG_MII)
-static int dw_mii_read(const char *devname, u8 addr, u8 reg, u16 *val)
-{
-	struct eth_device *dev;
-
-	dev = eth_get_dev_by_name(devname);
-	if (dev)
-		eth_mdio_read(dev, addr, reg, val);
-
-	return 0;
-}
-
-static int dw_mii_write(const char *devname, u8 addr, u8 reg, u16 val)
-{
-	struct eth_device *dev;
-
-	dev = eth_get_dev_by_name(devname);
-	if (dev)
-		eth_mdio_write(dev, addr, reg, val);
-
-	return 0;
+	return 1;
 }
-#endif
 
-int designware_initialize(u32 id, ulong base_addr, u32 phy_addr, u32 interface)
+int designware_initialize(ulong base_addr, u32 interface)
 {
 	struct eth_device *dev;
 	struct dw_eth_dev *priv;
@@ -533,19 +374,14 @@ int designware_initialize(u32 id, ulong base_addr, u32 phy_addr, u32 interface)
 	memset(dev, 0, sizeof(struct eth_device));
 	memset(priv, 0, sizeof(struct dw_eth_dev));
 
-	sprintf(dev->name, "mii%d", id);
+	sprintf(dev->name, "dwmac.%lx", base_addr);
 	dev->iobase = (int)base_addr;
 	dev->priv = priv;
 
-	eth_getenv_enetaddr_by_index("eth", id, &dev->enetaddr[0]);
-
 	priv->dev = dev;
 	priv->mac_regs_p = (struct eth_mac_regs *)base_addr;
 	priv->dma_regs_p = (struct eth_dma_regs *)(base_addr +
 			DW_DMA_BASE_OFFSET);
-	priv->address = phy_addr;
-	priv->phy_configured = 0;
-	priv->interface = interface;
 
 	dev->init = dw_eth_init;
 	dev->send = dw_eth_send;
@@ -555,8 +391,10 @@ int designware_initialize(u32 id, ulong base_addr, u32 phy_addr, u32 interface)
 
 	eth_register(dev);
 
-#if defined(CONFIG_MII)
-	miiphy_register(dev->name, dw_mii_read, dw_mii_write);
-#endif
-	return 1;
+	priv->interface = interface;
+
+	dw_mdio_init(dev->name, priv->mac_regs_p);
+	priv->bus = miiphy_get_dev_by_name(dev->name);
+
+	return dw_phy_init(dev);
 }

drivers/net/designware.h

@@ -16,8 +16,6 @@
 
 #define CONFIG_MACRESET_TIMEOUT	(3 * CONFIG_SYS_HZ)
 #define CONFIG_MDIO_TIMEOUT	(3 * CONFIG_SYS_HZ)
-#define CONFIG_PHYRESET_TIMEOUT	(3 * CONFIG_SYS_HZ)
-#define CONFIG_AUTONEG_TIMEOUT	(5 * CONFIG_SYS_HZ)
 
 struct eth_mac_regs {
 	u32 conf;		/* 0x00 */
@@ -217,14 +215,9 @@ struct dmamacdescr {
 #endif
 
 struct dw_eth_dev {
-	u32 address;
 	u32 interface;
-	u32 speed;
-	u32 duplex;
 	u32 tx_currdescnum;
 	u32 rx_currdescnum;
-	u32 phy_configured;
-	u32 link_printed;
 
 	struct dmamacdescr tx_mac_descrtable[CONFIG_TX_DESCR_NUM];
 	struct dmamacdescr rx_mac_descrtable[CONFIG_RX_DESCR_NUM];
@@ -236,15 +229,8 @@ struct dw_eth_dev {
 	struct eth_dma_regs *dma_regs_p;
 
 	struct eth_device *dev;
+	struct phy_device *phydev;
+	struct mii_dev *bus;
 };
 
-/* Speed specific definitions */
-#define SPEED_10M		1
-#define SPEED_100M		2
-#define SPEED_1000M		3
-
-/* Duplex mode specific definitions */
-#define HALF_DUPLEX		1
-#define FULL_DUPLEX		2
-
 #endif

include/configs/bf609-ezkit.h

@@ -72,12 +72,13 @@
 #define CONFIG_NET_MULTI
 #define CONFIG_HOSTNAME		"bf609-ezkit"
 #define CONFIG_DESIGNWARE_ETH
+#define CONFIG_PHY_ADDR		1
 #define CONFIG_DW_PORTS		1
-#define CONFIG_DW_AUTONEG
 #define CONFIG_DW_ALTDESCRIPTOR
 #define CONFIG_CMD_NET
 #define CONFIG_CMD_MII
 #define CONFIG_MII
+#define CONFIG_PHYLIB
 
 /* i2c Settings */
 #define CONFIG_BFIN_TWI_I2C

include/configs/spear-common.h

@@ -17,11 +17,9 @@
 /* Ethernet driver configuration */
 #define CONFIG_MII
 #define CONFIG_DESIGNWARE_ETH
-#define CONFIG_DW_SEARCH_PHY
-#define CONFIG_DW0_PHY				1
 #define CONFIG_NET_MULTI
+#define CONFIG_PHYLIB
 #define CONFIG_PHY_RESET_DELAY			10000		/* in usec */
-#define CONFIG_DW_AUTONEG
 #define CONFIG_PHY_GIGE			/* Include GbE speed/duplex detection */
 
 /* USBD driver configuration */

include/configs/spear6xx_evb.h

@@ -37,6 +37,9 @@
 #define CONFIG_SYS_FSMC_NAND_8BIT
 #define CONFIG_SYS_NAND_BASE			0xD2000000
 
+/* Ethernet PHY configuration */
+#define CONFIG_PHY_NATSEMI
+
 /* Environment Settings */
 #define CONFIG_EXTRA_ENV_SETTINGS              CONFIG_EXTRA_ENV_USBTTY
 

include/netdev.h

@@ -36,7 +36,7 @@ int calxedaxgmac_initialize(u32 id, ulong base_addr);
 int cs8900_initialize(u8 dev_num, int base_addr);
 int davinci_emac_initialize(void);
 int dc21x4x_initialize(bd_t *bis);
-int designware_initialize(u32 id, ulong base_addr, u32 phy_addr, u32 interface);
+int designware_initialize(ulong base_addr, u32 interface);
 int dm9000_initialize(bd_t *bis);
 int dnet_eth_initialize(int id, void *regs, unsigned int phy_addr);
 int e1000_initialize(bd_t *bis);