powerpc: T1023RDB: Remove macro CONFIG_T1023RDB

Use TARGET_T1023RDB from Kconfig instead.

Signed-off-by: York Sun <york.sun@nxp.com>

board/freescale/t102xrdb/ddr.c

@@ -136,7 +136,7 @@ found:
 	popts->data_bus_width = DDR_DATA_BUS_WIDTH_32;
 #endif
 
-#ifdef CONFIG_T1023RDB
+#ifdef CONFIG_TARGET_T1023RDB
 	popts->wrlvl_ctl_2 = 0x07070606;
 	popts->half_strength_driver_enable = 1;
 	popts->cpo_sample = 0x43;

board/freescale/t102xrdb/eth_t102xrdb.c

@@ -73,7 +73,7 @@ int board_eth_init(bd_t *bis)
 	case 0x135:
 		/* set the on-board 2.5G SGMII AQR105 PHY */
 		fm_info_set_phy_address(FM1_DTSEC3, SGMII_AQR_PHY_ADDR);
-#ifdef CONFIG_T1023RDB
+#ifdef CONFIG_TARGET_T1023RDB
 		/* set the on-board 1G SGMII RTL8211F PHY */
 		fm_info_set_phy_address(FM1_DTSEC1, SGMII_RTK_PHY_ADDR);
 #endif
@@ -92,7 +92,7 @@ int board_eth_init(bd_t *bis)
 			fm_info_set_mdio(i, dev);
 			break;
 		case PHY_INTERFACE_MODE_SGMII:
-#if defined(CONFIG_T1023RDB)
+#if defined(CONFIG_TARGET_T1023RDB)
 			dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
 #elif defined(CONFIG_T1024RDB)
 			dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);

board/freescale/t102xrdb/t102xrdb.c

@@ -19,7 +19,7 @@
 #include "t102xrdb.h"
 #ifdef CONFIG_T1024RDB
 #include "cpld.h"
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
 #include <i2c.h>
 #include <mmc.h>
 #endif
@@ -27,7 +27,7 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-#ifdef CONFIG_T1023RDB
+#ifdef CONFIG_TARGET_T1023RDB
 enum {
 	GPIO1_SD_SEL    = 0x00020000, /* GPIO1_14, 0: eMMC, 1:SD/MMC */
 	GPIO1_EMMC_SEL,
@@ -54,7 +54,7 @@ int checkboard(void)
 #if defined(CONFIG_T1024RDB)
 	printf("Board rev: 0x%02x CPLD ver: 0x%02x, ",
 	       CPLD_READ(hw_ver), CPLD_READ(sw_ver));
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
 	printf("Rev%c, ", t1023rdb_ctrl(GPIO3_GET_VERSION) + 'B');
 #endif
 	printf("boot from ");
@@ -74,7 +74,7 @@ int checkboard(void)
 		reg = ((reg & CPLD_LBMAP_MASK) >> CPLD_LBMAP_SHIFT);
 		printf("NOR vBank%d\n", reg);
 	}
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
 #ifdef CONFIG_NAND
 	puts("NAND\n");
 #else
@@ -196,7 +196,7 @@ int ft_board_setup(void *blob, bd_t *bd)
 	fdt_fixup_board_enet(blob);
 #endif
 
-#ifdef CONFIG_T1023RDB
+#ifdef CONFIG_TARGET_T1023RDB
 	if (t1023rdb_ctrl(GPIO3_GET_VERSION) > 0)
 		fdt_enable_nor(blob);
 #endif
@@ -204,7 +204,7 @@ int ft_board_setup(void *blob, bd_t *bd)
 	return 0;
 }
 
-#ifdef CONFIG_T1023RDB
+#ifdef CONFIG_TARGET_T1023RDB
 /* Enable NOR flash for RevC */
 static void fdt_enable_nor(void *blob)
 {

board/freescale/t102xrdb/t102xrdb.h

@@ -9,7 +9,7 @@
 
 void fdt_fixup_board_enet(void *blob);
 void pci_of_setup(void *blob, bd_t *bd);
-#ifdef CONFIG_T1023RDB
+#ifdef CONFIG_TARGET_T1023RDB
 static u32 t1023rdb_ctrl(u32 ctrl_type);
 static void fdt_enable_nor(void *blob);
 #endif

configs/T1023RDB_NAND_defconfig

@@ -12,7 +12,7 @@ CONFIG_FIT=y
 CONFIG_FIT_VERBOSE=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="T1023RDB,RAMBOOT_PBL,SPL_FSL_PBL,NAND"
+CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPL_FSL_PBL,NAND"
 CONFIG_BOOTDELAY=10
 CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 CONFIG_SPL=y

configs/T1023RDB_SDCARD_defconfig

@@ -12,7 +12,7 @@ CONFIG_FIT=y
 CONFIG_FIT_VERBOSE=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="T1023RDB,RAMBOOT_PBL,SPL_FSL_PBL,SDCARD"
+CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPL_FSL_PBL,SDCARD"
 CONFIG_BOOTDELAY=10
 CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 CONFIG_SPL=y

configs/T1023RDB_SECURE_BOOT_defconfig

@@ -7,7 +7,6 @@ CONFIG_FIT=y
 CONFIG_FIT_VERBOSE=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="T1023RDB"
 CONFIG_BOOTDELAY=10
 CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 CONFIG_HUSH_PARSER=y

configs/T1023RDB_SPIFLASH_defconfig

@@ -13,7 +13,7 @@ CONFIG_FIT=y
 CONFIG_FIT_VERBOSE=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="T1023RDB,RAMBOOT_PBL,SPL_FSL_PBL,SPIFLASH"
+CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPL_FSL_PBL,SPIFLASH"
 CONFIG_BOOTDELAY=10
 CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 CONFIG_SPL=y

configs/T1023RDB_defconfig

@@ -5,7 +5,6 @@ CONFIG_FIT=y
 CONFIG_FIT_VERBOSE=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="T1023RDB"
 CONFIG_BOOTDELAY=10
 CONFIG_SYS_CONSOLE_IS_IN_ENV=y
 CONFIG_HUSH_PARSER=y

include/configs/T102xRDB.h

@@ -62,7 +62,7 @@
 #define CONFIG_SYS_LDSCRIPT	"arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
 #if defined(CONFIG_T1024RDB)
 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1024_nand_rcw.cfg
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1023_nand_rcw.cfg
 #endif
 #define CONFIG_SPL_NAND_BOOT
@@ -81,7 +81,7 @@
 #endif
 #if defined(CONFIG_T1024RDB)
 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1024_spi_rcw.cfg
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1023_spi_rcw.cfg
 #endif
 #define CONFIG_SPL_SPI_BOOT
@@ -100,7 +100,7 @@
 #endif
 #if defined(CONFIG_T1024RDB)
 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1024_sd_rcw.cfg
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1023_sd_rcw.cfg
 #endif
 #define CONFIG_SPL_MMC_BOOT
@@ -177,7 +177,7 @@
 #define CONFIG_ENV_OFFSET		0x100000	/* 1MB */
 #if defined(CONFIG_T1024RDB)
 #define CONFIG_ENV_SECT_SIZE		0x10000
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
 #define CONFIG_ENV_SECT_SIZE		0x40000
 #endif
 #elif defined(CONFIG_SDCARD)
@@ -192,7 +192,7 @@
 #define CONFIG_ENV_SIZE			0x2000
 #if defined(CONFIG_T1024RDB)
 #define CONFIG_ENV_OFFSET		(2 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
 #define CONFIG_ENV_OFFSET		(10 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #endif
 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
@@ -277,7 +277,7 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_SPD_BUS_NUM	0
 #define SPD_EEPROM_ADDRESS	0x51
 #define CONFIG_SYS_SDRAM_SIZE	4096	/* for fixed parameter use */
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
 #define CONFIG_SYS_FSL_DDR4
 #define CONFIG_SYS_DDR_RAW_TIMING
 #define CONFIG_SYS_SDRAM_SIZE   2048
@@ -303,7 +303,7 @@ unsigned long get_board_ddr_clk(void);
 /* NOR Flash Timing Params */
 #if defined(CONFIG_T1024RDB)
 #define CONFIG_SYS_NOR_CSOR	CSOR_NAND_TRHZ_80
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
 #define CONFIG_SYS_NOR_CSOR    (CSOR_NOR_ADM_SHIFT(0) | \
 				CSOR_NAND_TRHZ_80 | CSOR_NOR_ADM_SHFT_MODE_EN)
 #endif
@@ -378,7 +378,7 @@ unsigned long get_board_ddr_clk(void);
 				| CSOR_NAND_SPRZ_224	/* Spare size = 224 */ \
 				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/
 #define CONFIG_SYS_NAND_BLOCK_SIZE	(512 * 1024)
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
 #define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 				| CSOR_NAND_ECC_MODE_4	/* 4-bit ECC */ \
@@ -733,7 +733,7 @@ unsigned long get_board_ddr_clk(void);
 #if defined(CONFIG_T1024RDB)
 #define CONFIG_SYS_FMAN_FW_ADDR		(3 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #define CONFIG_SYS_QE_FW_ADDR		(4 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
 #define CONFIG_SYS_FMAN_FW_ADDR		(11 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #define CONFIG_SYS_QE_FW_ADDR		(12 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #endif
@@ -766,7 +766,7 @@ unsigned long get_board_ddr_clk(void);
 #define RGMII_PHY2_ADDR		0x6
 #define SGMII_AQR_PHY_ADDR	0x2
 #define FM1_10GEC1_PHY_ADDR	0x1
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
 #define RGMII_PHY1_ADDR		0x1
 #define SGMII_RTK_PHY_ADDR	0x3
 #define SGMII_AQR_PHY_ADDR	0x2

scripts/config_whitelist.txt

@@ -7792,7 +7792,6 @@ CONFIG_SYS_XWAY_EBU_BOOTCFG
 CONFIG_SYS_ZYNQ_QSPI_WAIT
 CONFIG_SYS_ZYNQ_SPI_WAIT
 CONFIG_SYS_i2C_FSL
-CONFIG_T1023RDB
 CONFIG_T1024RDB
 CONFIG_T1040QDS
 CONFIG_T2080QDS