Exynos542x: add L2 control register configuration

This patch does 3 things:
1. Enables ECC by setting 21st bit of L2CTLR.
2. Restore data and tag RAM latencies to 3 cycles because iROM sets
   0x3000400 L2CTLR value during switching.
3. Disable clean/evict push to external by setting 3rd bit of L2ACTLR.
   We need to restore this here due to switching.

Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

arch/arm/cpu/armv7/exynos/lowlevel_init.c

@@ -46,6 +46,42 @@ enum {
 };
 
 #ifdef CONFIG_EXYNOS5420
+/*
+ * Enable ECC by setting L2CTLR[21].
+ * Set L2CTLR[7] to make tag ram latency 3 cycles and
+ * set L2CTLR[1] to make data ram latency 3 cycles.
+ * We need to make RAM latency of 3 cycles here because cores
+ * power ON and OFF while switching. And everytime a core powers
+ * ON, iROM provides it a default L2CTLR value 0x400 which stands
+ * for TAG RAM setup of 1 cycle. Hence, we face a need of
+ * restoring data and tag latency values.
+ */
+static void configure_l2_ctlr(void)
+{
+	uint32_t val;
+
+	mrc_l2_ctlr(val);
+	val |= (1 << 21);
+	val |= (1 << 7);
+	val |= (1 << 1);
+	mcr_l2_ctlr(val);
+}
+
+/*
+ * Set L2ACTLR[27] to prevent the clock generator from stopping
+ * the L2 logic clock.
+ * Set L2ACTLR[3] to disable clean/evict push to external.
+ */
+static void configure_l2_actlr(void)
+{
+	uint32_t val;
+
+	mrc_l2_aux_ctlr(val);
+	val |= (1 << 27);
+	val |= (1 << 3);
+	mcr_l2_aux_ctlr(val);
+}
+
 /*
  * Power up secondary CPUs.
  */
@@ -80,7 +116,19 @@ static void low_power_start(void)
 
 	/* Set the CPU to SVC32 mode */
 	svc32_mode_en();
-	v7_enable_l2_hazard_detect();
+
+#ifndef CONFIG_SYS_L2CACHE_OFF
+	/* Read MIDR for Primary Part Number */
+	mrc_midr(val);
+	val = (val >> 4);
+	val &= 0xf;
+
+	if (val == 0xf) {
+		configure_l2_ctlr();
+		configure_l2_actlr();
+		v7_enable_l2_hazard_detect();
+	}
+#endif
 
 	/* Invalidate L1 & TLB */
 	val = 0x0;
@@ -138,6 +186,7 @@ static void power_down_core(void)
 static void secondary_cores_configure(void)
 {
 	/* Setup L2 cache */
+	configure_l2_ctlr();
 	v7_enable_l2_hazard_detect();
 
 	/* Clear secondary boot iRAM base */

arch/arm/cpu/armv7/exynos/soc.c

@@ -37,30 +37,32 @@ void enable_caches(void)
  */
 static void exynos5_set_l2cache_params(void)
 {
-	unsigned int val = 0;
+	unsigned int l2ctlr = 0, l2actlr = 0;
 
 	/* Read L2CTLR value */
-	asm volatile("mrc p15, 1, %0, c9, c0, 2\n" : "=r"(val));
+	asm volatile("mrc p15, 1, %0, c9, c0, 2\n" : "=r"(l2ctlr));
 
-	/* Set cache setup and latency cycles */
-	val |= CACHE_TAG_RAM_SETUP |
-		CACHE_DATA_RAM_SETUP |
-		CACHE_TAG_RAM_LATENCY |
+	/* Set cache latency cycles */
+	l2ctlr |= CACHE_TAG_RAM_LATENCY |
 		CACHE_DATA_RAM_LATENCY;
 
-	/* Write new vlaue to L2CTLR */
-	asm volatile("mcr p15, 1, %0, c9, c0, 2\n" : : "r"(val));
-
 	if (proid_is_exynos5420() || proid_is_exynos5800()) {
 		/* Read L2ACTLR value */
-		asm volatile("mrc	p15, 1, %0, c15, c0, 0" : "=r" (val));
+		asm volatile("mrc p15, 1, %0, c15, c0, 0" : "=r" (l2actlr));
 
 		/* Disable clean/evict push to external */
-		val |= CACHE_DISABLE_CLEAN_EVICT;
+		l2actlr |= CACHE_DISABLE_CLEAN_EVICT;
 
 		/* Write new vlaue to L2ACTLR */
-		asm volatile("mcr	p15, 1, %0, c15, c0, 0" : : "r" (val));
+		asm volatile("mcr p15, 1, %0, c15, c0, 0" : : "r" (l2actlr));
+	} else {
+		/* Set cache setup cycles */
+		l2ctlr |= CACHE_TAG_RAM_SETUP |
+			CACHE_DATA_RAM_SETUP;
 	}
+
+	/* Write new vlaue to L2CTLR */
+	asm volatile("mcr p15, 1, %0, c9, c0, 2\n" : : "r"(l2ctlr));
 }
 
 /*