rockchip: add basic support for evb-rk3288 board

evb-3288 board RK3288-based development board with 2 USB ports, HDMI,
VGA, micro-SD card, audio, WiFi and Gigabit Ethernet. It also includes
on-board 8G eMMC and 2GB of SDRAM. Expansion connector provide access to
display pins, I2C, SPI, UART and GPIOs. This add some basic files
required to allow the board to output serial messaged and can run
command(mmc info etc).

evb-rk3288 also supports booting from eMMC or SD card, the default is eMMC.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

arch/arm/dts/Makefile

@@ -31,6 +31,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
 	rk3288-firefly.dtb \
 	rk3288-jerry.dtb \
 	rk3288-rock2-square.dtb \
+	rk3288-evb.dtb \
 	rk3036-sdk.dtb
 dtb-$(CONFIG_ARCH_MESON) += \
 	meson-gxbb-odroidc2.dtb

arch/arm/dts/rk3288-evb.dts

@@ -0,0 +1,59 @@
+/*
+ * (C) Copyright 2016 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier:     GPL-2.0+ X11
+ */
+
+/dts-v1/;
+#include "rk3288-evb.dtsi"
+
+/ {
+	model = "Evb-RK3288";
+	compatible = "evb-rk3288,evb-rk3288", "rockchip,rk3288";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+};
+
+&dmc {
+	rockchip,num-channels = <2>;
+	rockchip,pctl-timing = <0x215 0xc8 0x0 0x35 0x26 0x2 0x70 0x2000d
+		0x6 0x0 0x8 0x4 0x17 0x24 0xd 0x6
+		0x4 0x8 0x4 0x76 0x4 0x0 0x30 0x0
+		0x1 0x2 0x2 0x4 0x0 0x0 0xc0 0x4
+		0x8 0x1f4>;
+	rockchip,phy-timing = <0x48d7dd93 0x187008d8 0x121076
+		0x0 0xc3 0x6 0x2>;
+	rockchip,sdram-channel = /bits/ 8 <0x2 0xa 0x3 0x2 0x2 0x0 0xe 0xe>;
+	rockchip,sdram-params = <0x20d266a4 0x5b6 2 533000000 6 9 0>;
+};
+
+&pinctrl {
+	u-boot,dm-pre-reloc;
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&uart2 {
+	u-boot,dm-pre-reloc;
+	reg-shift = <2>;
+};
+
+&sdmmc {
+	u-boot,dm-pre-reloc;
+};
+
+&emmc {
+	u-boot,dm-pre-reloc;
+};
+
+&gpio3 {
+	u-boot,dm-pre-reloc;
+};
+
+&gpio8 {
+	u-boot,dm-pre-reloc;
+};

arch/arm/dts/rk3288-evb.dtsi

@@ -0,0 +1,379 @@
+/*
+ * (C) Copyright 2016 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier:     GPL-2.0+ X11
+ */
+
+#include "rk3288.dtsi"
+
+/ {
+	memory {
+		reg = <0 0x80000000>;
+	};
+
+	keys: gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		button@0 {
+			gpio-key,wakeup = <1>;
+			gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+			label = "GPIO Power";
+			linux,code = <116>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pwr_key>;
+		};
+	};
+
+	vcc_sys: vsys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc_flash: flash-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_flash";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_io>;
+	};
+
+	vcc_5v: usb-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcc_host_5v: usb-host-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&host_vbus_drv>;
+		regulator-name = "vcc_host_5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&vcc_5v>;
+	};
+
+	vcc_otg_5v: usb-otg-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&otg_vbus_drv>;
+		regulator-name = "vcc_otg_5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&vcc_5v>;
+	};
+};
+
+&cpu0 {
+	cpu0-supply = <&vdd_cpu>;
+};
+
+&emmc {
+	broken-cd;
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	disable-wp;
+	non-removable;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_pwr>, <&emmc_bus8>;
+	vmmc-supply = <&vcc_io>;
+	vqmmc-supply = <&vcc_flash>;
+	status = "okay";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c5>;
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	vdd_cpu: syr827@40 {
+		compatible = "silergy,syr827";
+		fcs,suspend-voltage-selector = <1>;
+		reg = <0x40>;
+		regulator-name = "vdd_cpu";
+		regulator-min-microvolt = <850000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vdd_gpu: syr828@41 {
+		compatible = "silergy,syr828";
+		fcs,suspend-voltage-selector = <1>;
+		reg = <0x41>;
+		regulator-name = "vdd_gpu";
+		regulator-min-microvolt = <850000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-always-on;
+		vin-supply = <&vcc_sys>;
+	};
+
+	hym8563: hym8563@51 {
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "xin32k";
+		interrupt-parent = <&gpio7>;
+		interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&rtc_int>;
+	};
+
+	act8846: act8846@5a {
+		compatible = "active-semi,act8846";
+		reg = <0x5a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwr_hold>;
+		system-power-controller;
+
+		regulators {
+			vcc_ddr: REG1 {
+				regulator-name = "vcc_ddr";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+			};
+
+			vcc_io: REG2 {
+				regulator-name = "vcc_io";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd_log: REG3 {
+				regulator-name = "vdd_log";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+
+			vcc_20: REG4 {
+				regulator-name = "vcc_20";
+				regulator-min-microvolt = <2000000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-always-on;
+			};
+
+			vccio_sd: REG5 {
+				regulator-name = "vccio_sd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd10_lcd: REG6 {
+				regulator-name = "vdd10_lcd";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			vcca_codec: REG7 {
+				regulator-name = "vcca_codec";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vcc_tp: REG8 {
+				regulator-name = "vcca_33";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vccio_pmu: REG9 {
+				regulator-name = "vccio_pmu";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vdd_10: REG10 {
+				regulator-name = "vdd_10";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			vcc_18: REG11 {
+				regulator-name = "vcc_18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			vcc18_lcd: REG12 {
+				regulator-name = "vcc18_lcd";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&pinctrl {
+	pcfg_output_high: pcfg-output-high {
+		output-high;
+	};
+
+	pcfg_output_low: pcfg-output-low {
+		output-low;
+	};
+
+	act8846 {
+		pwr_hold: pwr-hold {
+			rockchip,pins = <0 9 RK_FUNC_GPIO &pcfg_output_high>;
+		};
+	};
+
+	hym8563 {
+		rtc_int: rtc-int {
+			rockchip,pins = <0 4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	keys {
+		pwr_key: pwr-key {
+			rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	sdmmc {
+		sdmmc_pwr: sdmmc-pwr {
+			rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb_host {
+		host_vbus_drv: host-vbus-drv {
+			rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb_otg {
+		otg_vbus_drv: otg-vbus-drv {
+			rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&saradc {
+	vref-supply = <&vcc_18>;
+	status = "okay";
+};
+
+&sdio0 {
+	broken-cd;
+	bus-width = <4>;
+	disable-wp;
+	non-removable;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio0_bus4>, <&sdio0_cmd>, <&sdio0_clk>;
+	vmmc-supply = <&vcc_18>;
+	status = "disabled";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	card-detect-delay = <200>;
+	disable-wp;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk>, <&sdmmc_cmd>, <&sdmmc_cd>, <&sdmmc_bus4>;
+	vmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_clk>, <&spi0_cs0>, <&spi0_tx>, <&spi0_rx>, <&spi0_cs1>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_xfer>, <&uart0_cts>, <&uart0_rts>;
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&usb_host1 {
+	status = "okay";
+};
+
+&usb_otg {
+	status = "okay";
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};
+
+&wdt {
+	status = "okay";
+};

arch/arm/mach-rockchip/rk3288-board-spl.c

@@ -251,7 +251,8 @@ void spl_board_init(void)
 	}
 #ifdef CONFIG_SPL_MMC_SUPPORT
 	if (!IS_ENABLED(CONFIG_TARGET_ROCK2) &&
-	    !IS_ENABLED(CONFIG_TARGET_FIREFLY_RK3288)) {
+	    !IS_ENABLED(CONFIG_TARGET_FIREFLY_RK3288) &&
+	    !IS_ENABLED(CONFIG_TARGET_EVB_RK3288)) {
 		ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_SDCARD);
 		if (ret) {
 			debug("%s: Failed to set up SD card\n", __func__);

arch/arm/mach-rockchip/rk3288/Kconfig

@@ -8,6 +8,14 @@ config TARGET_FIREFLY_RK3288
 	  also includes on-board eMMC and 1GB of SDRAM. Expansion connectors
 	  provide access to display pins, I2C, SPI, UART and GPIOs.
 
+config TARGET_EVB_RK3288
+	bool "Evb-RK3288"
+	help
+	  EVB-RK3288 is a RK3288-based development board with 2 USB ports,
+	  HDMI, VGA, micro-SD card, audio, WiFi  and Gigabit Ethernet, It
+	  also includes on-board eMMC and 2GB of SDRAM. Expansion connectors
+	  provide access to display pins, I2C, SPI, UART and GPIOs.
+
 config TARGET_CHROMEBOOK_JERRY
 	bool "Google/Rockchip Veyron-Jerry Chromebook"
 	help
@@ -45,4 +53,6 @@ source "board/firefly/firefly-rk3288/Kconfig"
 
 source "board/radxa/rock2/Kconfig"
 
+source "board/evb-rk3288/evb-rk3288/Kconfig"
+
 endif

board/evb-rk3288/evb-rk3288/Kconfig

@@ -0,0 +1,15 @@
+if TARGET_EVB_RK3288
+
+config SYS_BOARD
+	default "evb-rk3288"
+
+config SYS_VENDOR
+	default "evb-rk3288"
+
+config SYS_CONFIG_NAME
+	default "evb-rk3288"
+
+config BOARD_SPECIFIC_OPTIONS # dummy
+	def_bool y
+
+endif

board/evb-rk3288/evb-rk3288/MAINTAINERS

@@ -0,0 +1,6 @@
+EVB-RK3288
+M:	Lin Huang <hl@rock-chips.com>
+S:	Maintained
+F:	board/evb-rk3288/evb-rk3288
+F:	include/configs/evb-rk3288.h
+F:	configs/evb-rk3288_defconfig

board/evb-rk3288/evb-rk3288/Makefile

@@ -0,0 +1,7 @@
+#
+# (C) Copyright 2016 Rockchip Electronics Co., Ltd
+#
+# SPDX-License-Identifier:     GPL-2.0+
+#
+
+obj-y	+= evb-rk3288.o

board/evb-rk3288/evb-rk3288/evb-rk3288.c

@@ -0,0 +1,15 @@
+/*
+ * (C) Copyright 2016 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+#include <common.h>
+#include <spl.h>
+
+void board_boot_order(u32 *spl_boot_list)
+{
+	/* eMMC prior to sdcard. */
+	spl_boot_list[0] = BOOT_DEVICE_MMC2;
+	spl_boot_list[1] = BOOT_DEVICE_MMC1;
+}

configs/evb-rk3288_defconfig

@@ -0,0 +1,67 @@
+CONFIG_ARM=y
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_ROCKCHIP_RK3288=y
+CONFIG_TARGET_EVB_RK3288=y
+CONFIG_SPL_STACK_R_ADDR=0x80000
+CONFIG_DEFAULT_DEVICE_TREE="rk3288-evb"
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x2000
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
+CONFIG_REGMAP=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_SPL_SYSCON=y
+CONFIG_CLK=y
+CONFIG_SPL_CLK=y
+CONFIG_ROCKCHIP_GPIO=y
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_SYSRESET=y
+CONFIG_DM_MMC=y
+CONFIG_ROCKCHIP_DWMMC=y
+CONFIG_PINCTRL=y
+# CONFIG_PINCTRL_FULL is not set
+CONFIG_SPL_PINCTRL=y
+# CONFIG_SPL_PINCTRL_FULL is not set
+CONFIG_ROCKCHIP_PINCTRL=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_ACT8846=y
+CONFIG_DM_REGULATOR=y
+CONFIG_REGULATOR_ACT8846=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_PWM=y
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_RAM=y
+CONFIG_SPL_RAM=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_BASE=0xff690000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550=y
+CONFIG_USE_PRIVATE_LIBGCC=y
+CONFIG_USE_TINY_PRINTF=y
+CONFIG_CMD_DHRYSTONE=y
+CONFIG_ERRNO_STR=y

doc/README.rockchip

@@ -36,11 +36,12 @@ You will need:
 Building
 ========
 
-At present three RK3288 boards are supported:
+At present four RK3288 boards are supported:
 
    - Firefly RK3288 - use firefly-rk3288 configuration
    - Radxa Rock 2 - use rock2 configuration
    - Hisense Chromebook - use chromebook_jerry configuration
+   - EVB RK3288 - use evb-rk3288 configuration
 
 Two RK3036 board are supported:
 

include/configs/evb-rk3288.h

@@ -0,0 +1,26 @@
+/*
+ * (C) Copyright 2016 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define ROCKCHIP_DEVICE_SETTINGS
+#include <configs/rk3288_common.h>
+
+#define CONFIG_SPL_MMC_SUPPORT
+
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 1
+/* SPL @ 32k for ~36k
+ * ENV @ 96k
+ * u-boot @ 128K
+ */
+#define CONFIG_ENV_OFFSET (96 * 1024)
+
+#define CONFIG_SYS_WHITE_ON_BLACK
+#define CONFIG_CONSOLE_SCROLL_LINES		10
+
+#endif