mx6sx: Add initial support for Samtec VIN|ING 2000 board

This patch adds initial support for Samtec VIN|ING 2000 board.

Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Marek Vasut <marex@denx.de>

arch/arm/cpu/armv7/mx6/Kconfig

@@ -204,6 +204,12 @@ config TARGET_UDOO_NEO
 	bool "UDOO Neo"
 	select SUPPORT_SPL
 
+config TARGET_SAMTEC_VINING_2000
+	bool "samtec VIN|ING 2000"
+	select MX6SX
+	select DM
+	select DM_THERMAL
+
 config TARGET_WANDBOARD
 	bool "wandboard"
 	select SUPPORT_SPL
@@ -259,6 +265,7 @@ source "board/freescale/mx6ullevk/Kconfig"
 source "board/phytec/pcm058/Kconfig"
 source "board/gateworks/gw_ventana/Kconfig"
 source "board/kosagi/novena/Kconfig"
+source "board/samtec/vining_2000/Kconfig"
 source "board/seco/Kconfig"
 source "board/solidrun/mx6cuboxi/Kconfig"
 source "board/technexion/pico-imx6ul/Kconfig"

board/samtec/vining_2000/Kconfig

@@ -0,0 +1,12 @@
+if TARGET_SAMTEC_VINING_2000
+
+config SYS_BOARD
+	default "vining_2000"
+
+config SYS_VENDOR
+	default "samtec"
+
+config SYS_CONFIG_NAME
+	default "vining_2000"
+
+endif

board/samtec/vining_2000/MAINTAINERS

@@ -0,0 +1,6 @@
+VINING_2000 BOARD
+M:	Ingo Schroeck <open-source@samtec.de>
+S:	Maintained
+F:	board/samtec/vining_2000/
+F:	include/configs/vining_2000.h
+F:	configs/vining_2000_defconfig

board/samtec/vining_2000/Makefile

@@ -0,0 +1,6 @@
+# (C) Copyright 2016 samtec automotive software & electronics gmbh
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := vining_2000.o

board/samtec/vining_2000/imximage.cfg

@@ -0,0 +1,132 @@
+/*
+ * Copyright (C) 2016 samtec automotive software & electronics gmbh
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* image version */
+
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * spi/sd/nand/onenand, qspi/nor
+ */
+
+BOOT_FROM	sd
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *	Addr-type register length (1,2 or 4 bytes)
+ *	Address	  absolute address of the register
+ *	value	  value to be stored in the register
+ */
+
+/* Enable all clocks */
+DATA 4 0x020c4068 0xffffffff
+DATA 4 0x020c406c 0xffffffff
+DATA 4 0x020c4070 0xffffffff
+DATA 4 0x020c4074 0xffffffff
+DATA 4 0x020c4078 0xffffffff
+DATA 4 0x020c407c 0xffffffff
+DATA 4 0x020c4080 0xffffffff
+DATA 4 0x020c4084 0xffffffff
+
+/* IOMUX - DDR IO Type */
+DATA 4 0x020e0618 0x000c0000
+DATA 4 0x020e05fc 0x00000000
+
+/* Clock */
+DATA 4 0x020e032c 0x00000030
+
+/* Address */
+DATA 4 0x020e0300 0x00000028
+DATA 4 0x020e02fc 0x00000028
+DATA 4 0x020e05f4 0x00000028
+
+/* Control */
+DATA 4 0x020e0340 0x00000028
+
+DATA 4 0x020e0320 0x00000000
+DATA 4 0x020e0310 0x00000028
+DATA 4 0x020e0314 0x00000028
+DATA 4 0x020e0614 0x00000028
+
+/* Data Strobe */
+DATA 4 0x020e05f8 0x00020000
+DATA 4 0x020e0330 0x00000028
+DATA 4 0x020e0334 0x00000028
+DATA 4 0x020e0338 0x00000028
+DATA 4 0x020e033c 0x00000028
+
+/* Data */
+DATA 4 0x020e0608 0x00020000
+DATA 4 0x020e060c 0x00000028
+DATA 4 0x020e0610 0x00000028
+DATA 4 0x020e061c 0x00000028
+DATA 4 0x020e0620 0x00000028
+DATA 4 0x020e02ec 0x00000028
+DATA 4 0x020e02f0 0x00000028
+DATA 4 0x020e02f4 0x00000028
+DATA 4 0x020e02f8 0x00000028
+
+/* Calibrations - ZQ */
+DATA 4 0x021b0800 0xa1390003
+
+/* Write leveling */
+DATA 4 0x021b080c 0x00290025
+DATA 4 0x021b0810 0x00210022
+
+/* DQS Read Gate */
+DATA 4 0x021b083c 0x4142013a
+DATA 4 0x021b0840 0x012e0123
+
+/* Read/Write Delay */
+DATA 4 0x021b0848 0x43474949
+DATA 4 0x021b0850 0x38383c38
+
+/* Read data bit delay */
+DATA 4 0x021b081c 0x33333333
+DATA 4 0x021b0820 0x33333333
+DATA 4 0x021b0824 0x33333333
+DATA 4 0x021b0828 0x33333333
+
+/* Complete calibration by forced measurement */
+DATA 4 0x021b08b8 0x00000800
+
+/* MMDC init - DDR3, 64-bit mode, only MMDC0 is initiated */
+DATA 4 0x021b0004 0x0002002d
+DATA 4 0x021b0008 0x00333040
+DATA 4 0x021b000c 0x676b52f2
+DATA 4 0x021b0010 0x926e8b63
+DATA 4 0x021b0014 0x01ff00db
+DATA 4 0x021b0018 0x00011740
+DATA 4 0x021b001c 0x00008000
+DATA 4 0x021b002c 0x000026d2
+DATA 4 0x021b0030 0x006b1023
+DATA 4 0x021b0040 0x0000005f
+DATA 4 0x021b0000 0x84190000
+
+/* Initialize MT41K256M16HA-125 - MR2 */
+DATA 4 0x021b001c 0x02008032
+/* MR3 */
+DATA 4 0x021b001c 0x00008033
+/* MR1 */
+DATA 4 0x021b001c 0x00048031
+/* MR0 */
+DATA 4 0x021b001c 0x15108030
+/* DDR device ZQ calibration */
+DATA 4 0x021b001c 0x04008040
+
+/* Final DDR setup, before operation start */
+DATA 4 0x021b0020 0x00007800
+DATA 4 0x021b0818 0x00022227
+DATA 4 0x021b001c 0x00000000

board/samtec/vining_2000/vining_2000.c

@@ -0,0 +1,517 @@
+/*
+ * Copyright (C) 2016 samtec automotive software & electronics gmbh
+ *
+ * Author: Christoph Fritz <chf.fritz@googlemail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/io.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <linux/sizes.h>
+#include <common.h>
+#include <fsl_esdhc.h>
+#include <mmc.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <power/pmic.h>
+#include <power/pfuze100_pmic.h>
+#include <usb.h>
+#include <usb/ehci-ci.h>
+#include <pwm.h>
+#include <wait_bit.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL  (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP |	\
+	PAD_CTL_PKE | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |	\
+	PAD_CTL_SRE_FAST)
+
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PKE |	\
+	PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_48ohm |		\
+	PAD_CTL_SRE_FAST)
+
+#define ENET_CLK_PAD_CTRL  PAD_CTL_DSE_34ohm
+
+#define ENET_RX_PAD_CTRL  (PAD_CTL_PKE |			\
+	PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_HIGH |		\
+	PAD_CTL_SRE_FAST)
+
+#define I2C_PAD_CTRL  (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP |	\
+	PAD_CTL_PKE | PAD_CTL_ODE | PAD_CTL_SPEED_MED |		\
+	PAD_CTL_DSE_40ohm)
+
+#define USDHC_CLK_PAD_CTRL  (PAD_CTL_HYS | PAD_CTL_SPEED_MED |	\
+	PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST)
+
+#define USDHC_PAD_CTRL  (PAD_CTL_HYS | PAD_CTL_PUS_47K_UP |	\
+	PAD_CTL_PKE |  PAD_CTL_SPEED_MED | PAD_CTL_DSE_80ohm |	\
+	PAD_CTL_SRE_FAST)
+
+#define GPIO_PAD_CTRL  (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP |	\
+	PAD_CTL_PKE)
+
+int dram_init(void)
+{
+	gd->ram_size = imx_ddr_size();
+
+	return 0;
+}
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+	MX6_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+	MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_CLK_PAD_CTRL),
+	MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DATA0__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DATA1__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DATA2__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DATA3__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_LCD1_VSYNC__GPIO3_IO_28 | MUX_PAD_CTRL(GPIO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc4_pads[] = {
+	MX6_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_CLK_PAD_CTRL),
+	MX6_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DATA0__USDHC4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DATA1__USDHC4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DATA2__USDHC4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DATA3__USDHC4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DATA4__USDHC4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DATA5__USDHC4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DATA6__USDHC4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DATA7__USDHC4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const fec1_pads[] = {
+	MX6_PAD_ENET1_MDC__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_MDIO__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII1_RD0__ENET1_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII1_RD1__ENET1_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII1_TD0__ENET1_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII1_TD1__ENET1_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII1_RX_CTL__ENET1_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII1_TX_CTL__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL) |
+		MUX_MODE_SION,
+	/* LAN8720 PHY Reset */
+	MX6_PAD_RGMII1_TD3__GPIO5_IO_9 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const pwm_led_pads[] = {
+	MX6_PAD_RGMII2_RD2__PWM2_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), /* green */
+	MX6_PAD_RGMII2_TD2__PWM6_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), /* red */
+	MX6_PAD_RGMII2_RD3__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), /* blue */
+};
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+#define PHY_RESET IMX_GPIO_NR(5, 9)
+
+int board_eth_init(bd_t *bis)
+{
+	struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+	int ret;
+	unsigned char eth1addr[6];
+
+	/* just to get secound mac address */
+	imx_get_mac_from_fuse(1, eth1addr);
+	if (!getenv("eth1addr") && is_valid_ethaddr(eth1addr))
+		eth_setenv_enetaddr("eth1addr", eth1addr);
+
+	imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
+
+	/*
+	 * Generate phy reference clock via pin IOMUX ENET_REF_CLK1/2 by erasing
+	 * ENET1/2_TX_CLK_DIR gpr1[14:13], so that reference clock is driven by
+	 * ref_enetpll0/1 and enable ENET1/2_TX_CLK output driver.
+	 */
+	clrsetbits_le32(&iomuxc_regs->gpr[1],
+			IOMUX_GPR1_FEC1_CLOCK_MUX2_SEL_MASK |
+			IOMUX_GPR1_FEC2_CLOCK_MUX2_SEL_MASK,
+			IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK |
+			IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK);
+
+	ret = enable_fec_anatop_clock(0, ENET_50MHZ);
+	if (ret)
+		goto eth_fail;
+
+	/* reset phy */
+	gpio_direction_output(PHY_RESET, 0);
+	mdelay(16);
+	gpio_set_value(PHY_RESET, 1);
+	mdelay(1);
+
+	ret = fecmxc_initialize_multi(bis, 0, CONFIG_FEC_MXC_PHYADDR,
+					IMX_FEC_BASE);
+	if (ret)
+		goto eth_fail;
+
+	return ret;
+
+eth_fail:
+	printf("FEC MXC: %s:failed (%i)\n", __func__, ret);
+	gpio_set_value(PHY_RESET, 0);
+	return ret;
+}
+
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+/* I2C1 for PMIC */
+static struct i2c_pads_info i2c_pad_info1 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_GPIO1_IO00__I2C1_SCL | PC,
+		.gpio_mode = MX6_PAD_GPIO1_IO00__GPIO1_IO_0 | PC,
+		.gp = IMX_GPIO_NR(1, 0),
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_GPIO1_IO01__I2C1_SDA | PC,
+		.gpio_mode = MX6_PAD_GPIO1_IO01__GPIO1_IO_1 | PC,
+		.gp = IMX_GPIO_NR(1, 1),
+	},
+};
+
+static struct pmic *pfuze_init(unsigned char i2cbus)
+{
+	struct pmic *p;
+	int ret;
+	u32 reg;
+
+	ret = power_pfuze100_init(i2cbus);
+	if (ret)
+		return NULL;
+
+	p = pmic_get("PFUZE100");
+	ret = pmic_probe(p);
+	if (ret)
+		return NULL;
+
+	pmic_reg_read(p, PFUZE100_DEVICEID, &reg);
+	printf("PMIC:  PFUZE100 ID=0x%02x\n", reg);
+
+	/* Set SW1AB stanby volage to 0.975V */
+	pmic_reg_read(p, PFUZE100_SW1ABSTBY, &reg);
+	reg &= ~SW1x_STBY_MASK;
+	reg |= SW1x_0_975V;
+	pmic_reg_write(p, PFUZE100_SW1ABSTBY, reg);
+
+	/* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
+	pmic_reg_read(p, PFUZE100_SW1ABCONF, &reg);
+	reg &= ~SW1xCONF_DVSSPEED_MASK;
+	reg |= SW1xCONF_DVSSPEED_4US;
+	pmic_reg_write(p, PFUZE100_SW1ABCONF, reg);
+
+	/* Set SW1C standby voltage to 0.975V */
+	pmic_reg_read(p, PFUZE100_SW1CSTBY, &reg);
+	reg &= ~SW1x_STBY_MASK;
+	reg |= SW1x_0_975V;
+	pmic_reg_write(p, PFUZE100_SW1CSTBY, reg);
+
+	/* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */
+	pmic_reg_read(p, PFUZE100_SW1CCONF, &reg);
+	reg &= ~SW1xCONF_DVSSPEED_MASK;
+	reg |= SW1xCONF_DVSSPEED_4US;
+	pmic_reg_write(p, PFUZE100_SW1CCONF, reg);
+
+	return p;
+}
+
+static int pfuze_mode_init(struct pmic *p, u32 mode)
+{
+	unsigned char offset, i, switch_num;
+	u32 id;
+	int ret;
+
+	pmic_reg_read(p, PFUZE100_DEVICEID, &id);
+	id = id & 0xf;
+
+	if (id == 0) {
+		switch_num = 6;
+		offset = PFUZE100_SW1CMODE;
+	} else if (id == 1) {
+		switch_num = 4;
+		offset = PFUZE100_SW2MODE;
+	} else {
+		printf("Not supported, id=%d\n", id);
+		return -EINVAL;
+	}
+
+	ret = pmic_reg_write(p, PFUZE100_SW1ABMODE, mode);
+	if (ret < 0) {
+		printf("Set SW1AB mode error!\n");
+		return ret;
+	}
+
+	for (i = 0; i < switch_num - 1; i++) {
+		ret = pmic_reg_write(p, offset + i * SWITCH_SIZE, mode);
+		if (ret < 0) {
+			printf("Set switch 0x%x mode error!\n",
+			       offset + i * SWITCH_SIZE);
+			return ret;
+		}
+	}
+
+	return ret;
+}
+
+int power_init_board(void)
+{
+	struct pmic *p;
+	int ret;
+
+	p = pfuze_init(I2C_PMIC);
+	if (!p)
+		return -ENODEV;
+
+	ret = pfuze_mode_init(p, APS_PFM);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+#ifdef CONFIG_USB_EHCI_MX6
+static iomux_v3_cfg_t const usb_otg_pads[] = {
+	/* OGT1 */
+	MX6_PAD_GPIO1_IO09__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_GPIO1_IO10__ANATOP_OTG1_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* OTG2 */
+	MX6_PAD_GPIO1_IO12__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)
+};
+
+static void setup_iomux_usb(void)
+{
+	imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
+					 ARRAY_SIZE(usb_otg_pads));
+}
+
+int board_usb_phy_mode(int port)
+{
+	if (port == 1)
+		return USB_INIT_HOST;
+	else
+		return usb_phy_mode(port);
+}
+#endif
+
+#ifdef CONFIG_PWM_IMX
+static int set_pwm_leds(void)
+{
+	int ret;
+
+	imx_iomux_v3_setup_multiple_pads(pwm_led_pads,
+					 ARRAY_SIZE(pwm_led_pads));
+	/* enable backlight PWM 2, green LED */
+	ret = pwm_init(1, 0, 0);
+	if (ret)
+		goto error;
+	/* duty cycle 200ns, period: 8000ns */
+	ret = pwm_config(1, 200, 8000);
+	if (ret)
+		goto error;
+	ret = pwm_enable(1);
+	if (ret)
+		goto error;
+
+	/* enable backlight PWM 1, blue LED */
+	ret = pwm_init(0, 0, 0);
+	if (ret)
+		goto error;
+	/* duty cycle 200ns, period: 8000ns */
+	ret = pwm_config(0, 200, 8000);
+	if (ret)
+		goto error;
+	ret = pwm_enable(0);
+	if (ret)
+		goto error;
+
+	/* enable backlight PWM 6, red LED */
+	ret = pwm_init(5, 0, 0);
+	if (ret)
+		goto error;
+	/* duty cycle 200ns, period: 8000ns */
+	ret = pwm_config(5, 200, 8000);
+	if (ret)
+		goto error;
+	ret = pwm_enable(5);
+
+error:
+	return ret;
+}
+#else
+static int set_pwm_leds(void)
+{
+	return 0;
+}
+#endif
+
+#define ADCx_HC0        0x00
+#define ADCx_HS         0x08
+#define ADCx_HS_C0      BIT(0)
+#define ADCx_R0         0x0c
+#define ADCx_CFG        0x14
+#define ADCx_CFG_SWMODE 0x308
+#define ADCx_GC         0x18
+#define ADCx_GC_CAL     BIT(7)
+
+static int read_adc(u32 *val)
+{
+	int ret;
+	void __iomem *b = map_physmem(ADC1_BASE_ADDR, 0x100, MAP_NOCACHE);
+
+	/* use software mode */
+	writel(ADCx_CFG_SWMODE, b + ADCx_CFG);
+
+	/* start auto calibration */
+	setbits_le32(b + ADCx_GC, ADCx_GC_CAL);
+	ret = wait_for_bit("ADC", b + ADCx_GC, ADCx_GC_CAL, ADCx_GC_CAL, 10, 0);
+	if (ret)
+		goto adc_exit;
+
+	/* start conversion */
+	writel(0, b + ADCx_HC0);
+
+	/* wait for conversion */
+	ret = wait_for_bit("ADC", b + ADCx_HS, ADCx_HS_C0, ADCx_HS_C0, 10, 0);
+	if (ret)
+		goto adc_exit;
+
+	/* read result */
+	*val = readl(b + ADCx_R0);
+
+adc_exit:
+	if (ret)
+		printf("ADC failure (ret=%i)\n", ret);
+	unmap_physmem(b, MAP_NOCACHE);
+	return ret;
+}
+
+#define VAL_UPPER	2498
+#define VAL_LOWER	1550
+
+static int set_pin_state(void)
+{
+	u32 val;
+	int ret;
+
+	ret = read_adc(&val);
+	if (ret)
+		return ret;
+
+	if (val >= VAL_UPPER)
+		setenv("pin_state", "connected");
+	else if (val < VAL_UPPER && val > VAL_LOWER)
+		setenv("pin_state", "open");
+	else
+		setenv("pin_state", "button");
+
+	return ret;
+}
+
+int board_late_init(void)
+{
+	int ret;
+
+	ret = set_pwm_leds();
+	if (ret)
+		return ret;
+
+	ret = set_pin_state();
+
+	return ret;
+}
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+
+	setup_iomux_usb();
+
+	return 0;
+}
+
+static struct fsl_esdhc_cfg usdhc_cfg[2] = {
+	{USDHC4_BASE_ADDR, 0, 8},
+	{USDHC2_BASE_ADDR, 0, 4},
+};
+
+#define USDHC2_CD_GPIO IMX_GPIO_NR(3, 28)
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+
+	if (cfg->esdhc_base == USDHC4_BASE_ADDR)
+		return 1;
+	if (cfg->esdhc_base == USDHC2_BASE_ADDR)
+		return !gpio_get_value(USDHC2_CD_GPIO);
+
+	return -EINVAL;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	int ret;
+
+	/*
+	 * According to the board_mmc_init() the following map is done:
+	 * (U-Boot device node)    (Physical Port)
+	 * mmc0                    USDHC4
+	 * mmc1                    USDHC2
+	 */
+	imx_iomux_v3_setup_multiple_pads(
+		usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
+	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+
+	imx_iomux_v3_setup_multiple_pads(
+		usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+	gpio_direction_input(USDHC2_CD_GPIO);
+	usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+
+	ret = fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+	if (ret) {
+		printf("Warning: failed to initialize USDHC4\n");
+		return ret;
+	}
+
+	ret = fsl_esdhc_initialize(bis, &usdhc_cfg[1]);
+	if (ret) {
+		printf("Warning: failed to initialize USDHC2\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* Address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+#ifdef CONFIG_SYS_I2C_MXC
+	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+#endif
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: VIN|ING 2000\n");
+
+	return 0;
+}

configs/vining_2000_defconfig

@@ -0,0 +1,31 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_TARGET_SAMTEC_VINING_2000=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/samtec/vining_2000/imximage.cfg"
+CONFIG_BOOTDELAY=0
+CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_PCI=y
+CONFIG_USB=y
+CONFIG_USB_STORAGE=y
+CONFIG_OF_LIBFDT=y
+CONFIG_MXC_USB_OTG_HACTIVE=y

include/configs/vining_2000.h

@@ -0,0 +1,123 @@
+/*
+ * Copyright (C) 2016 samtec automotive software & electronics gmbh
+ *
+ * Configuration settings for the Samtec VIN|ING 2000 board.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include "mx6_common.h"
+
+#ifdef CONFIG_SPL
+#include "imx6_spl.h"
+#endif
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(3 * SZ_1M)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE		UART1_BASE
+
+#define BOOT_TARGET_DEVICES(func) \
+	func(MMC, mmc, 0) \
+	func(MMC, mmc, 1) \
+	func(USB, usb, 0) \
+	func(PXE, pxe, na) \
+	func(DHCP, dhcp, na)
+#include <config_distro_bootcmd.h>
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_MEMTEST_START	0x80000000
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x10000)
+
+#define CONFIG_STACKSIZE		SZ_128K
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS		1
+#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* MMC Configuration */
+#define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC4_BASE_ADDR
+
+/* I2C Configs */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
+#define CONFIG_SYS_I2C_SPEED		  100000
+
+/* PMIC */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_PFUZE100
+#define CONFIG_POWER_PFUZE100_I2C_ADDR	0x08
+
+/* Network */
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+
+#define IMX_FEC_BASE			ENET_BASE_ADDR
+#define CONFIG_FEC_MXC_PHYADDR          0x0
+
+#define CONFIG_FEC_XCV_TYPE             RMII
+#define CONFIG_ETHPRIME                 "FEC"
+
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ATHEROS
+
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MX6
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_ASIX
+#define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS   0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+#endif
+
+#define CONFIG_CMD_PCI
+#ifdef CONFIG_CMD_PCI
+#define CONFIG_PCI_SCAN_SHOW
+#define CONFIG_PCIE_IMX
+#define CONFIG_PCIE_IMX_PERST_GPIO	IMX_GPIO_NR(4, 6)
+#endif
+
+#define CONFIG_IMX_THERMAL
+
+#define CONFIG_PWM_IMX
+#define CONFIG_IMX6_PWM_PER_CLK 66000000
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+#define CONFIG_ENV_OFFSET		(8 * SZ_64K)
+#define CONFIG_ENV_SIZE			SZ_8K
+#define CONFIG_ENV_OFFSET_REDUND	(9 * SZ_64K)
+#define CONFIG_ENV_SIZE_REDUND		CONFIG_ENV_SIZE
+#define CONFIG_ENV_IS_IN_MMC
+
+#ifdef CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SUPPORT_EMMC_BOOT
+#define CONFIG_EFI_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SUPPORT_EMMC_RPMB
+#define CONFIG_SYS_MMC_ENV_DEV		0 /* USDHC4 eMMC */
+/* 0=user, 1=boot0, 2=boot1, * 4..7=general0..3. */
+#define CONFIG_SYS_MMC_ENV_PART		1 /* boot0 */
+#endif
+
+#endif				/* __CONFIG_H */