usb: s3c-otg: Rename remaining macros

The driver is actually for the Designware DWC2 controller.
This patch renames the remaining S3C_* macros to match the
DWC2 naming.

Signed-off-by: Marek Vasut <marex@denx.de>

drivers/usb/gadget/dwc2_udc_otg.c

@@ -190,7 +190,7 @@ static void udc_reinit(struct dwc2_udc *dev)
 	dev->ep0state = WAIT_FOR_SETUP;
 
 	/* basic endpoint records init */
-	for (i = 0; i < S3C_MAX_ENDPOINTS; i++) {
+	for (i = 0; i < DWC2_MAX_ENDPOINTS; i++) {
 		struct dwc2_ep *ep = &dev->ep[i];
 
 		if (i != 0)
@@ -380,7 +380,7 @@ static void stop_activity(struct dwc2_udc *dev,
 	dev->gadget.speed = USB_SPEED_UNKNOWN;
 
 	/* prevent new request submissions, kill any outstanding requests  */
-	for (i = 0; i < S3C_MAX_ENDPOINTS; i++) {
+	for (i = 0; i < DWC2_MAX_ENDPOINTS; i++) {
 		struct dwc2_ep *ep = &dev->ep[i];
 		ep->stopped = 1;
 		nuke(ep, -ESHUTDOWN);
@@ -448,7 +448,7 @@ static void reconfig_usbd(struct dwc2_udc *dev)
 	writel(DEPCTL_EPDIS|DEPCTL_SNAK, &reg->out_endp[EP0_CON].doepctl);
 	writel(DEPCTL_EPDIS|DEPCTL_SNAK, &reg->in_endp[EP0_CON].diepctl);
 
-	for (i = 1; i < S3C_MAX_ENDPOINTS; i++) {
+	for (i = 1; i < DWC2_MAX_ENDPOINTS; i++) {
 		writel(DEPCTL_EPDIS|DEPCTL_SNAK, &reg->out_endp[i].doepctl);
 		writel(DEPCTL_EPDIS|DEPCTL_SNAK, &reg->in_endp[i].diepctl);
 	}
@@ -470,7 +470,7 @@ static void reconfig_usbd(struct dwc2_udc *dev)
 	writel((NPTX_FIFO_SIZE >> 2) << 16 | ((RX_FIFO_SIZE >> 2)) << 0,
 	       &reg->gnptxfsiz);
 
-	for (i = 1; i < S3C_MAX_HW_ENDPOINTS; i++)
+	for (i = 1; i < DWC2_MAX_HW_ENDPOINTS; i++)
 		writel((PTX_FIFO_SIZE >> 2) << 16 |
 		       ((RX_FIFO_SIZE + NPTX_FIFO_SIZE +
 			 PTX_FIFO_SIZE*(i-1)) >> 2) << 0,
@@ -479,13 +479,13 @@ static void reconfig_usbd(struct dwc2_udc *dev)
 	/* Flush the RX FIFO */
 	writel(RX_FIFO_FLUSH, &reg->grstctl);
 	while (readl(&reg->grstctl) & RX_FIFO_FLUSH)
-		debug("%s: waiting for S3C_UDC_OTG_GRSTCTL\n", __func__);
+		debug("%s: waiting for DWC2_UDC_OTG_GRSTCTL\n", __func__);
 
 	/* Flush all the Tx FIFO's */
 	writel(TX_FIFO_FLUSH_ALL, &reg->grstctl);
 	writel(TX_FIFO_FLUSH_ALL | TX_FIFO_FLUSH, &reg->grstctl);
 	while (readl(&reg->grstctl) & TX_FIFO_FLUSH)
-		debug("%s: waiting for S3C_UDC_OTG_GRSTCTL\n", __func__);
+		debug("%s: waiting for DWC2_UDC_OTG_GRSTCTL\n", __func__);
 
 	/* 13. Clear NAK bit of EP0, EP1, EP2*/
 	/* For Slave mode*/
@@ -515,7 +515,7 @@ static void set_max_pktsize(struct dwc2_udc *dev, enum usb_device_speed speed)
 	}
 
 	dev->ep[0].ep.maxpacket = ep0_fifo_size;
-	for (i = 1; i < S3C_MAX_ENDPOINTS; i++)
+	for (i = 1; i < DWC2_MAX_ENDPOINTS; i++)
 		dev->ep[i].ep.maxpacket = ep_fifo_size;
 
 	/* EP0 - Control IN (64 bytes)*/

drivers/usb/gadget/dwc2_udc_otg_priv.h

@@ -24,8 +24,8 @@
 #define EP_FIFO_SIZE		512
 #define EP_FIFO_SIZE2		1024
 /* ep0-control, ep1in-bulk, ep2out-bulk, ep3in-int */
-#define S3C_MAX_ENDPOINTS	4
-#define S3C_MAX_HW_ENDPOINTS	16
+#define DWC2_MAX_ENDPOINTS	4
+#define DWC2_MAX_HW_ENDPOINTS	16
 
 #define WAIT_FOR_SETUP          0
 #define DATA_STATE_XMIT         1
@@ -81,7 +81,7 @@ struct dwc2_udc {
 	struct s3c_plat_otg_data *pdata;
 
 	int ep0state;
-	struct dwc2_ep ep[S3C_MAX_ENDPOINTS];
+	struct dwc2_ep ep[DWC2_MAX_ENDPOINTS];
 
 	unsigned char usb_address;
 

drivers/usb/gadget/dwc2_udc_otg_regs.h

@@ -83,11 +83,11 @@ struct dwc2_usbotg_reg {
 /*===================================================================== */
 /*definitions related to CSR setting */
 
-/* S3C_UDC_OTG_GOTGCTL */
+/* DWC2_UDC_OTG_GOTGCTL */
 #define B_SESSION_VALID		(0x1<<19)
 #define A_SESSION_VALID		(0x1<<18)
 
-/* S3C_UDC_OTG_GAHBCFG */
+/* DWC2_UDC_OTG_GAHBCFG */
 #define PTXFE_HALF			(0<<8)
 #define PTXFE_ZERO			(1<<8)
 #define NPTXFE_HALF			(0<<7)
@@ -102,11 +102,11 @@ struct dwc2_usbotg_reg {
 #define GBL_INT_UNMASK			(1<<0)
 #define GBL_INT_MASK			(0<<0)
 
-/* S3C_UDC_OTG_GRSTCTL */
+/* DWC2_UDC_OTG_GRSTCTL */
 #define AHB_MASTER_IDLE		(1u<<31)
 #define CORE_SOFT_RESET		(0x1<<0)
 
-/* S3C_UDC_OTG_GINTSTS/S3C_UDC_OTG_GINTMSK core interrupt register */
+/* DWC2_UDC_OTG_GINTSTS/DWC2_UDC_OTG_GINTMSK core interrupt register */
 #define INT_RESUME			(1u<<31)
 #define INT_DISCONN			(0x1<<29)
 #define INT_CONN_ID_STS_CNG		(0x1<<28)
@@ -146,22 +146,22 @@ struct dwc2_usbotg_reg {
 #define USB_LOW_6MHZ			(0x2<<1)
 #define USB_FULL_48MHZ			(0x3<<1)
 
-/* S3C_UDC_OTG_GRXSTSP STATUS */
+/* DWC2_UDC_OTG_GRXSTSP STATUS */
 #define OUT_PKT_RECEIVED		(0x2<<17)
 #define OUT_TRANSFER_COMPLELTED	(0x3<<17)
 #define SETUP_TRANSACTION_COMPLETED	(0x4<<17)
 #define SETUP_PKT_RECEIVED		(0x6<<17)
 #define GLOBAL_OUT_NAK			(0x1<<17)
 
-/* S3C_UDC_OTG_DCTL device control register */
+/* DWC2_UDC_OTG_DCTL device control register */
 #define NORMAL_OPERATION		(0x1<<0)
 #define SOFT_DISCONNECT		(0x1<<1)
 
-/* S3C_UDC_OTG_DAINT device all endpoint interrupt register */
+/* DWC2_UDC_OTG_DAINT device all endpoint interrupt register */
 #define DAINT_OUT_BIT			(16)
 #define DAINT_MASK			(0xFFFF)
 
-/* S3C_UDC_OTG_DIEPCTL0/DOEPCTL0 device
+/* DWC2_UDC_OTG_DIEPCTL0/DOEPCTL0 device
    control IN/OUT endpoint 0 control register */
 #define DEPCTL_EPENA			(0x1<<31)
 #define DEPCTL_EPDIS			(0x1<<30)
@@ -191,9 +191,9 @@ struct dwc2_usbotg_reg {
 #define DIEPCTL0_NEXT_EP_BIT		(11)
 
 
-/* S3C_UDC_OTG_DIEPMSK/DOEPMSK device IN/OUT endpoint
+/* DWC2_UDC_OTG_DIEPMSK/DOEPMSK device IN/OUT endpoint
    common interrupt mask register */
-/* S3C_UDC_OTG_DIEPINTn/DOEPINTn device IN/OUT endpoint interrupt register */
+/* DWC2_UDC_OTG_DIEPINTn/DOEPINTn device IN/OUT endpoint interrupt register */
 #define BACK2BACK_SETUP_RECEIVED	(0x1<<6)
 #define INTKNEPMIS			(0x1<<5)
 #define INTKN_TXFEMP			(0x1<<4)

drivers/usb/gadget/dwc2_udc_otg_xfer_dma.c

@@ -652,14 +652,14 @@ static int dwc2_queue(struct usb_ep *_ep, struct usb_request *_req,
 		} else if (ep_is_in(ep)) {
 			gintsts = readl(&reg->gintsts);
 			debug_cond(DEBUG_IN_EP,
-				   "%s: ep_is_in, S3C_UDC_OTG_GINTSTS=0x%x\n",
+				   "%s: ep_is_in, DWC2_UDC_OTG_GINTSTS=0x%x\n",
 				   __func__, gintsts);
 
 			setdma_tx(ep, req);
 		} else {
 			gintsts = readl(&reg->gintsts);
 			debug_cond(DEBUG_OUT_EP != 0,
-				   "%s:ep_is_out, S3C_UDC_OTG_GINTSTS=0x%x\n",
+				   "%s:ep_is_out, DWC2_UDC_OTG_GINTSTS=0x%x\n",
 				   __func__, gintsts);
 
 			setdma_rx(ep, req);