ARM: UniPhier: enable Driver Model and UART on SPL

Enable CONFIG_SPL_DM and CONFIG_SPL_SERIAL_SUPPORT, which provide
Driver Model UART support on SPL.

CONFIG_SYS_SPL_MALLOC_{START,SIZE} should be dropped because simple
malloc is preferred on SPL.  Dlmalloc requires some static variables
on .data section that is not available yet for NOR boot mode etc.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

arch/arm/mach-uniphier/spl.c

@@ -1,6 +1,7 @@
 /*
  * Copyright (C) 2013-2015 Panasonic Corporation
- *   Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ * Copyright (C) 2015      Socionext Inc.
+ *   Author: Masahiro Yamada <yamada.masahiro@socionext.com>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
@@ -52,6 +53,12 @@ void spl_board_init(void)
 
 	led_write(L, 3, , );
 
+#ifdef CONFIG_SPL_SERIAL_SUPPORT
+	preloader_console_init();
+#endif
+
+	led_write(L, 4, , );
+
 	{
 		int res;
 
@@ -61,9 +68,9 @@ void spl_board_init(void)
 				;
 		}
 	}
-	led_write(L, 4, , );
+	led_write(L, 5, , );
 
 	enable_dpll_ssc();
 
-	led_write(L, 5, , );
+	led_write(L, 6, , );
 }

configs/ph1_ld4_defconfig

@@ -2,6 +2,7 @@ CONFIG_ARM=y
 CONFIG_ARCH_UNIPHIER=y
 CONFIG_DM=y
 CONFIG_DM_SERIAL=y
+CONFIG_SPL_DM=y
 CONFIG_DM_I2C=y
 CONFIG_MACH_PH1_LD4=y
 CONFIG_PFC_MICRO_SUPPORT_CARD=y

configs/ph1_pro4_defconfig

@@ -2,6 +2,7 @@ CONFIG_ARM=y
 CONFIG_ARCH_UNIPHIER=y
 CONFIG_DM=y
 CONFIG_DM_SERIAL=y
+CONFIG_SPL_DM=y
 CONFIG_DM_I2C=y
 CONFIG_MACH_PH1_PRO4=y
 CONFIG_PFC_MICRO_SUPPORT_CARD=y

configs/ph1_sld8_defconfig

@@ -2,6 +2,7 @@ CONFIG_ARM=y
 CONFIG_ARCH_UNIPHIER=y
 CONFIG_DM=y
 CONFIG_DM_SERIAL=y
+CONFIG_SPL_DM=y
 CONFIG_DM_I2C=y
 CONFIG_MACH_PH1_SLD8=y
 CONFIG_PFC_MICRO_SUPPORT_CARD=y

include/configs/uniphier.h

@@ -280,9 +280,6 @@
 #define CONFIG_SKIP_LOWLEVEL_INIT
 #endif
 
-#define CONFIG_SYS_SPL_MALLOC_START	(0x0ff00000)
-#define CONFIG_SYS_SPL_MALLOC_SIZE	(0x00004000)
-
 #ifdef CONFIG_SPL_BUILD
 #define CONFIG_SYS_INIT_SP_ADDR		(0x0ff08000)
 #else
@@ -292,6 +289,7 @@
 #define CONFIG_PANIC_HANG
 
 #define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_SERIAL_SUPPORT
 #define CONFIG_SPL_NAND_SUPPORT
 
 #define CONFIG_SPL_LIBCOMMON_SUPPORT	/* for mem_malloc_init */