net: eth_designware: select PHYLIB in Kconfig

Select PHYLIB in drivers/net/Kconfig. And remove CONFIG_PHYLIB
from legacy board header files.

This fixed the warnings when both ALTERA_TSE and ETH_DESIGNWARE
are selected.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reported-by: Pavel Machek <pavel@denx.de>
Acked-by: Chin Liang See <clsee@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Tested-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

drivers/net/Kconfig

@@ -88,6 +88,7 @@ config ETH_SANDBOX_RAW
 
 config ETH_DESIGNWARE
 	bool "Synopsys Designware Ethernet MAC"
+	select PHYLIB
 	help
 	  This MAC is present in SoCs from various vendors. It supports
 	  100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to

drivers/net/designware.c

@@ -22,10 +22,6 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-#if !defined(CONFIG_PHYLIB)
-# error "DesignWare Ether MAC requires PHYLIB - missing CONFIG_PHYLIB"
-#endif
-
 static int dw_mdio_read(struct mii_dev *bus, int addr, int devad, int reg)
 {
 	struct eth_mac_regs *mac_p = bus->priv;

include/configs/axs101.h

@@ -95,7 +95,6 @@
 /*
  * Ethernet PHY configuration
  */
-#define CONFIG_PHYLIB
 #define CONFIG_MII
 #define CONFIG_PHY_GIGE
 

include/configs/bf609-ezkit.h

@@ -75,7 +75,6 @@
 #define CONFIG_DW_ALTDESCRIPTOR
 #define CONFIG_CMD_MII
 #define CONFIG_MII
-#define CONFIG_PHYLIB
 
 /* i2c Settings */
 #define CONFIG_SYS_I2C

include/configs/galileo.h

@@ -45,7 +45,6 @@
 /* 10/100M Ethernet support */
 #define CONFIG_DESIGNWARE_ETH
 #define CONFIG_DW_ALTDESCRIPTOR
-#define CONFIG_PHYLIB
 
 /* Environment configuration */
 #define CONFIG_ENV_SECT_SIZE		0x1000

include/configs/socfpga_common.h

@@ -109,7 +109,6 @@
 #define CONFIG_DW_ALTDESCRIPTOR
 #define CONFIG_MII
 #define CONFIG_AUTONEG_TIMEOUT		(15 * CONFIG_SYS_HZ)
-#define CONFIG_PHYLIB
 #define CONFIG_PHY_GIGE
 #endif
 

include/configs/spear-common.h

@@ -17,7 +17,6 @@
 
 /* Ethernet driver configuration */
 #define CONFIG_MII
-#define CONFIG_PHYLIB
 #define CONFIG_PHY_RESET_DELAY			10000		/* in usec */
 #define CONFIG_PHY_GIGE			/* Include GbE speed/duplex detection */
 

include/configs/stv0991.h

@@ -53,7 +53,6 @@
 /* GMAC related configs */
 
 #define CONFIG_MII
-#define CONFIG_PHYLIB
 #define CONFIG_DW_ALTDESCRIPTOR
 #define CONFIG_PHY_MICREL
 

include/configs/sunxi-common.h

@@ -313,7 +313,6 @@ extern int soft_i2c_gpio_scl;
 #define CONFIG_PHY_GIGE			/* GMAC can use gigabit PHY	*/
 #define CONFIG_PHY_ADDR		1
 #define CONFIG_MII			/* MII PHY management		*/
-#define CONFIG_PHYLIB
 #endif
 
 #ifdef CONFIG_USB_EHCI_HCD

include/configs/tb100.h

@@ -42,7 +42,6 @@
 /*
  * Ethernet PHY configuration
  */
-#define CONFIG_PHYLIB
 #define CONFIG_PHY_GIGE
 
 /*

include/configs/x600.h

@@ -77,7 +77,6 @@
 
 /* Ethernet config options */
 #define CONFIG_MII
-#define CONFIG_PHYLIB
 #define CONFIG_PHY_RESET_DELAY			10000		/* in usec */
 #define CONFIG_PHY_ADDR		0	/* PHY address */
 #define CONFIG_PHY_GIGE			/* Include GbE speed/duplex detection */