Merge branch 'master' of git://www.denx.de/git/u-boot-imx

board/freescale/mx6sabresd/mx6sabresd.c

@@ -177,13 +177,27 @@ static iomux_v3_cfg_t const rgb_pads[] = {
 	MX6_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 | MUX_PAD_CTRL(NO_PAD_CTRL),
 	MX6_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 | MUX_PAD_CTRL(NO_PAD_CTRL),
 	MX6_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const bl_pads[] = {
 	MX6_PAD_SD1_DAT3__GPIO1_IO21 | MUX_PAD_CTRL(NO_PAD_CTRL),
 };
 
+static void enable_backlight(void)
+{
+	imx_iomux_v3_setup_multiple_pads(bl_pads, ARRAY_SIZE(bl_pads));
+	gpio_direction_output(DISP0_PWR_EN, 1);
+}
+
 static void enable_rgb(struct display_info_t const *dev)
 {
 	imx_iomux_v3_setup_multiple_pads(rgb_pads, ARRAY_SIZE(rgb_pads));
-	gpio_direction_output(DISP0_PWR_EN, 1);
+	enable_backlight();
+}
+
+static void enable_lvds(struct display_info_t const *dev)
+{
+	enable_backlight();
 }
 
 static struct i2c_pads_info i2c_pad_info1 = {
@@ -370,7 +384,7 @@ struct display_info_t const displays[] = {{
 	.addr	= 0,
 	.pixfmt	= IPU_PIX_FMT_RGB666,
 	.detect	= NULL,
-	.enable	= NULL,
+	.enable	= enable_lvds,
 	.mode	= {
 		.name           = "Hannstar-XGA",
 		.refresh        = 60,

board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c

@@ -66,7 +66,7 @@ DECLARE_GLOBAL_DATA_PTR;
 #define IOX_SDI IMX_GPIO_NR(5, 10)
 #define IOX_STCP IMX_GPIO_NR(5, 7)
 #define IOX_SHCP IMX_GPIO_NR(5, 11)
-#define IOX_OE IMX_GPIO_NR(5, 18)
+#define IOX_OE IMX_GPIO_NR(5, 8)
 
 static iomux_v3_cfg_t const iox_pads[] = {
 	/* IOX_SDI */
@@ -117,7 +117,7 @@ static enum qn_level seq[3][2] = {
 
 static enum qn_func qn_output[8] = {
 	qn_reset, qn_reset, qn_reset, qn_enable, qn_disable, qn_reset,
-	qn_disable, qn_enable
+	qn_disable, qn_disable
 };
 
 static void iox74lv_init(void)
@@ -154,8 +154,6 @@ static void iox74lv_init(void)
 	 * shift register will be output to pins
 	 */
 	gpio_direction_output(IOX_STCP, 1);
-
-	gpio_direction_output(IOX_OE, 1);
 };
 
 #ifdef CONFIG_SYS_I2C_MXC
@@ -305,7 +303,7 @@ static void setup_iomux_uart(void)
 
 #define QSPI_PAD_CTRL1	\
 	(PAD_CTL_SRE_FAST | PAD_CTL_SPEED_MED | \
-	 PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_60ohm)
+	 PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_120ohm)
 
 static iomux_v3_cfg_t const quadspi_pads[] = {
 	MX6_PAD_NAND_WP_B__QSPI_A_SCLK | MUX_PAD_CTRL(QSPI_PAD_CTRL1),

board/freescale/mx7dsabresd/mx7dsabresd.c

@@ -171,7 +171,7 @@ static enum qn_level seq[3][2] = {
 
 static enum qn_func qn_output[8] = {
 	qn_disable, qn_reset, qn_reset, qn_reset, qn_reset, qn_reset, qn_enable,
-	qn_enable
+	qn_disable
 };
 
 static void iox74lv_init(void)

board/warp7/README

@@ -0,0 +1,63 @@
+How to Update U-Boot on Warp7 board
+----------------------------------
+
+Required software on the host PC:
+
+- imx_usb_loader: https://github.com/boundarydevices/imx_usb_loader
+
+- dfu-util: http://dfu-util.sourceforge.net/releases/ (if you are in a
+Debian distribution then you can get it via libdfu-dev package)
+
+- libusb: http://libusb.org/ (if you are in a Debian distribution
+then you can get it via libusb-dev and libusb-1.0-0-dev)
+
+In U-Boot folder, build U-Boot for Warp7:
+
+$ make mrproper
+$ make warp7_config
+$ make
+
+This will generate the U-Boot binary called u-boot.imx.
+
+Put warp7 board in USB download mode: 
+
+Remove the CPU board from the base board then put switch 2 in the upper
+position
+
+Connect a USB to serial adapter between the host PC and warp7
+
+Connect a USB cable between the OTG warp7 port and the host PC
+
+Copy u-boot.imx to the imx_usb_loader folder.
+
+Load u-boot.imx via USB:
+
+$ sudo ./imx_usb u-boot.imx
+
+Then U-Boot should start and its messages will appear in the console program.
+
+Open a terminal program such as minicom
+
+Use the default environment variables:
+
+=> env default -f -a
+=> saveenv
+
+Run the DFU command:
+=> dfu 0 mmc 0
+
+Transfer u-boot.imx that will be flashed into the eMMC:
+
+$ sudo dfu-util -D u-boot.imx -a boot
+
+Then on the U-Boot prompt the following message should be seen after a
+successful upgrade:
+
+#DOWNLOAD ... OK
+Ctrl+C to exit ...
+
+Remove power from the warp7 board.
+
+Put warp7 board into normal boot mode (put the switch 2 in the lower position)
+
+Power up the board and the new updated U-Boot should boot from eMMC

board/warp7/warp7.c

@@ -32,6 +32,10 @@ int dram_init(void)
 	return 0;
 }
 
+static iomux_v3_cfg_t const wdog_pads[] = {
+	MX7D_PAD_GPIO1_IO00__WDOG1_WDOG_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
 static iomux_v3_cfg_t const uart1_pads[] = {
 	MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
 	MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
@@ -100,3 +104,20 @@ int board_usb_phy_mode(int port)
 {
 	return USB_INIT_DEVICE;
 }
+
+int board_late_init(void)
+{
+	struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
+
+	imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
+
+	set_wdog_reset(wdog);
+
+	/*
+	 * Do not assert internal WDOG_RESET_B_DEB(controlled by bit 4),
+	 * since we use PMIC_PWRON to reset the board.
+	 */
+	clrsetbits_le16(&wdog->wcr, 0, 0x10);
+
+	return 0;
+}

include/configs/warp7.h

@@ -16,9 +16,10 @@
 #define CONFIG_MXC_UART_BASE		UART1_IPS_BASE_ADDR
 
 /* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN		(32 * SZ_1M)
+#define CONFIG_SYS_MALLOC_LEN		(35 * SZ_1M)
 
 #define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_LATE_INIT
 
 /* MMC Config*/
 #define CONFIG_SYS_FSL_ESDHC_ADDR       USDHC3_BASE_ADDR
@@ -27,10 +28,7 @@
 #define CONFIG_SYS_MMC_IMG_LOAD_PART	1
 
 #define CONFIG_DFU_ENV_SETTINGS \
-	"dfu_alt_info=image raw 0 0x800000;"\
-		"u-boot raw 0 0x4000;"\
-		"bootimg part 0 1;"\
-		"rootfs part 0 2\0" \
+	"dfu_alt_info=boot raw 0x2 0x400 mmcpart 1\0" \
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	CONFIG_DFU_ENV_SETTINGS \